Tektronix TDS 620A User manual
Service Manual
TDS 620A, 640A & 644A
Digitizing Oscilloscope
070-8718-04
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
Copyright Tektronix, Inc. 1993. All rights reserved.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
Printed in the U.S.A.
Tektronix, Inc., P.O. Box 1000, Wilsonville, OR 97070–1000
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
WARRANTY
Tektronix warrants that the products that it manufactures and sells will be free from defects in materials and
workmanship for a period of three (3) years from the date of shipment. If a product proves defective during this
warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor,
or will provide a replacement in exchange for the defective product.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration
of the warranty period and make suitable arrangements for the performance of service. Customer shall be
responsible for packaging and shipping the defective product to the service center designated by Tektronix, with
shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a
location within the country in which the Tektronix service center is located. Customer shall be responsible for
paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage
resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product;
b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any
damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been
modified or integrated with other products when the effect of such modification or integration increases the time
or difficulty of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX IN LIEU OF ANY OTHER WARRANTIES, EXPRESS
OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’
RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND
EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.
TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR
THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
$/3("$ +2 )
!)$ ,% ,+1$+10
(01 ,% (&2/$0 3((
(01 ,% !)$0 4(
%$15 2** /5 4(((
-$"(%(" 1(,+0
-$"(%(" 1(,+0 7
$+$/ ) /,#2"1 $0"/(-1(,+ 7
0$/ +1$/% "$ 7
%# &
$ "# &
" %"! # &
&
(&+ ) ".2(0(1(,+ 501$* 7
,/(6,+1 ) 501$* 7
/(&&$/ 501$* 7
".2(0(1(,+ ,+1/,) 7
+7, /# 0$/ 00(01 +"$ 7
! &
%$ #$ &
$ 02/$*$+1 00(01 +"$ 7
%"# " &
#%" &
$ " ## &
1,/ &$ +# 7
(0-) 5 7
&
,*(+ ) / (10 7
// +1$# ' / "1$/(01("0 7
5-(" ) ' / "1$/(01("0 7
% ( (',',+
(',',+
)*,#'! ' (*&,#('
+#'! ,"#+ '-% 2
(* *.##'! 2
,*,!1 (* *.##'! 2
'-% ,*-,-* 2
'-% ('.',#('+ 2
&,#* 1
+0 1
0$&#* 1
$,*('#0 *.# 2
))%+0 '!) )-! 1
'!) &) #!)+!&% )-! 1
# )-! 1
#'#'! ,"* ' (*&,#(' 2
'*% ' (*&,#(' 2
-))%1#'! )*,#'! (/* 2
&.) &) %&)$+!&% 1
')+!% &#+ 1
$&)0 ",' &.) 1
)*,#'! '.#*('&', 2
')+!% $')+,) 1
%+!#+!&% (,!)$%+* 1
))%1#'! ' ',**-),#'! (/* 2
&.) % 1
&.) 1
)$!#'! '+,*-,#('+ 2
'+,%% ),#('+ 2
'*% )*,#'! '+,*-,#('+ 2
*' 1(-, 2
+# *(-*+ 2
&. +& &.) % 1
&. +& * #' 1
&. +& * + ++,* %, 1
&. +& + ,%+!&%* 1
&. +& + &$'#/ ,%+!&%* 1
"(*1 ( )*,#('
#*-#, +*#),#(' 2
(!# ('.',#('+ 2
(-% .*.#/ 2
' *! *)/ )/.
-1$ )0'
-!*-() -$!$/$*)
-$ ! -* 0- . 3
) -' )./-0/$*). 3
*)1 )/$*). 3
'! ./. 3
Verify Internal Adjustment, Self Compensation,
and Diagnostics 4Ć4...................................
0)/$*)' ./. 3
Verify All Input Channels 4Ć7...............................
Verify the Time Base 4Ć8...................................
Verify the Main and Delayed Trigger Systems 4Ć9.............
Verify the File System (Optional on TDS 620A and 640A) 4Ć11...
-!*-() ./. 3
Prerequisites 4Ć13.........................................
Equipment Required 4Ć14...................................
Test Record 4Ć17..........................................
$")' ,0$.$/$*) 2./ ( # &. 3
Check Accuracy of Offset (Zero Setting) 4Ć21..................
Check DC Gain and Voltage Measurement Accuracy 4Ć23......
Check Analog Bandwidth 4Ć29..............................
Check Delay Between Channels 4Ć33........................
$( . 2./ ( # &. 3
Check Accuracy for LongĆTerm Sample Rate, Delay Time,
and Delta Time Measurements 4Ć37......................
-$"" - 2./ ( # &. 3
Check Accuracy (Time) for PulseĆGlitch or PulseĆWidth
Triggering 4Ć40........................................
Check Accuracy, TriggerĆLevel or Threshold, DC Coupled 4Ć43..
Sensitivity, Edge Trigger, DC Coupled 4Ć46....................
0/+0/ $")' # &. 3
Check Outputs Ċ A X1 (for TDS 620A) or CH 3 (for
TDS 640A or 644A), Main and Delayed Trigger 4Ć51........
Check Probe Compensator Output 4Ć54......................
+/$*) $ * -$"" - # &. 3
Check Video Trigger 4Ć59...................................
%0./( )/ -* 0- .
%0./( )/ -* 0- . 3
,0$- ( )/. !*- -!*-() 3
Personnel 5Ć1............................................
WarmĆ p Period 5Ć1......................................
Access 5Ć2...............................................
System 5Ć2..............................................
" % %$*$*)
%$*$*)
iv
Option l Peripher ls 5Ć2...................................
Test Equipment 5Ć2.......................................
) .
Performing the Adjustments 5Ć3............................
Complete Adjustment 5Ć3..................................
Individu l Adjustments 5Ć3.................................
P rti l Adjustment 5Ć4.....................................
Adjustment After Rep ir 5Ć4................................
Adjustment Dependencies 5Ć4.............................
'+ &#$* '+ ( .
!+)*#$* $)*(+* %$) .
H rdw re Inst ll tion 5Ć6..................................
Softw re Inst ll tion 5Ć7...................................
Softw reĆB sed Adjustments 5Ć7...........................
(% !+)*#$* %( * (% .
Compens te the Probe 5Ć10................................
Me sure Probe B ndwidth 5Ć12.............................
Adjust the Probe Ċ High Frequency Response 5Ć14...........
)&"- ))#"- !+)*#$* .
Brightness nd Contr st Adjustment
(TDS 620A nd 640A - Monochrome - Only) 5Ć18........
Rot tion, Brightness, nd Contr st Adjustment
(TDS 644A - Color - Only) 5Ć21.........................
$*$$
$*$$ $%(#* %$ .
(%+() %* $ ) * %$ .
(,$* $ .
Prec utions 6Ć2..........................................
Susceptibility to ESD 6Ć2..................................
$)&* %$ $ "$ $ .
$(" ( .
$)&* %$ $ "$ $ (%+() .
Inspection Ċ Exterior 6Ć6..................................
Cle ning Procedure Ċ Exterior 6Ć6.........................
Inspection Ċ Interior 6Ć7..................................
Cle ning Procedure Ċ Interior 6Ć8..........................
Lubric tion 6Ć8...........................................
#%," $ $)*""* %$ (%+() .
(&(* %$ / ") .
List of Modules 6Ć10.......................................
Gener l Instructions 6Ć10...................................
Summ ry of Procedures 6Ć10...............................
" % %$)$)(
'+! $*" v
(( '%*' /
'%*'( %' -)'$" %*"( /
FrontĆP nel Knobs 6Ć17....................................
Line Fuse nd Line Cord 6Ć18...............................
EMI G skets 6Ć19..........................................
Re r Cover nd C binet 6Ć20................................
Front Cover, Trim Ring, Menu Buttons, nd Attenu tor P nel 6Ć23
A12 FrontĆP nel Assembly 6Ć25.............................
Displ yĆFr me Assembly 6Ć28...............................
C binet Modules 6Ć29......................................
'%*'( %' *)'/ ((!( %*"( /
A15 Attenu tor Assembly 6Ć31...............................
F n 6Ć32..................................................
A14 D1 Bus nd An logĆPower nd Digit lĆPower C bles 6Ć33..
A23 SerP r Bo rd Ċ RS232/Centronics H rdcopy Interf ce 6Ć35
A29 Video Trigger Bo rd 6Ć37...............................
A11 Processor/Displ y Bo rd 6Ć42...........................
Top Cover nd Bo rd Br ckets 6Ć44..........................
Re rĆP nel C bles 6Ć45.....................................
A10 Acquisition Bo rd 6Ć46.................................
Floppy Disk 6Ć48..........................................
Re r Ch ssis 6Ć50.........................................
'%*'( %' $$'/ ((!( %*"( /
A16 Low Volt ge Power Supply 6Ć52.........................
A20 or A30 Displ y Assembly nd Supply Fuse 6Ć53...........
Front Subp nel 6Ć58.......................................
M in Ch ssis 6Ć59.........................................
!(((#". %' "$!$ /
'%*"( %%)!$ /
!$%()!( /
!'#,' &)( /
vi
vii
Figure 2Ć1:ăPowerĆCord Plug Identification 2Ć8......................
Figure 2Ć2:ăMap of Display Functions 2Ć14...........................
Figure 4Ć1:ăMap of Display Functions 4Ć3...........................
Figure 4Ć2:ăVerifying Adjustments and SignalĆPath Compensation 4Ć5..
Figure 4Ć3:ăUniversal Test Hookup for Functional Tests 4Ć7............
Figure 4Ć4:ăMeasurement of DC Offset Accuracy at Zero Setting 4Ć23...
Figure 4Ć5:ăInitial Test Hookup 4Ć24.................................
Figure 4Ć6:ăMeasurement of the DC Accuracy for Delta
Measurements 4Ć25...........................................
Figure 4Ć7:ăMeasurement of DC Accuracy at Maximum Offset
and Position 4Ć28..............................................
Figure 4Ć8:ăInitial Test Hookup 4Ć29.................................
Figure 4Ć9:ăMeasurement of Analog Bandwidth 4Ć32..................
Figure 4Ć10:ăInitial Test Hookup 4Ć34................................
Figure 4Ć11:ăMeasurement of Channel Delay 4Ć35....................
Figure 4Ć12:ăInitial Test Hookup 4Ć37................................
Figure 4Ć13:ăMeasurement of Accuracy Ċ LongĆTerm and
Delay Time 4Ć38...............................................
Figure 4Ć14:ăInitial Test Hookup 4Ć40................................
Figure 4Ć15:ăMeasurement of Time Accuracy for Pulse and
Glitch Triggering 4Ć42..........................................
Figure 4Ć16:ăInitial Test Hookup 4Ć43................................
Figure 4Ć17:ăMeasurement of TriggerĆLevel Accuracy 4Ć45.............
Figure 4Ć18:ăInitial Test Hookup 4Ć47................................
Figure 4Ć19:ăMeasurement of Trigger Sensitivity 4Ć48..................
Figure 4Ć20:ăInitial Test Hookup 4Ć51................................
Figure 4Ć21:ăMeasurement of Main Trigger Out Limits 4Ć52.............
Figure 4Ć22:ăInitial Test Hookup 4Ć54................................
Figure 4Ć23:ăMeasurement of Probe Compensator Frequency 4Ć56.....
Figure 4Ć24:ăSubsequent Test Hookup 4Ć57..........................
Figure 4Ć25:ăMeasurement of Probe Compensator Amplitude 4Ć58......
Figure 4Ć26:ăJitter Test Hookup 4Ć60................................
Figure 4Ć27:ăJitter Test Displayed aveform 4Ć60.....................
Figure 4Ć28:ăJitter Test hen Completed 4Ć62........................
Figure 4Ć29:ăTriggered Signal Range Test Ċ 300 mV 4Ć63.............
Figure 4Ć30:ăTriggered Signal Range Test Ċ 75 mV 4Ć64..............
Figure 4Ć31:ă60 Hz Rejection Test Hookup 4Ć65.......................
Figure 4Ć32:ă60 Hz Rejection Test Setup Signal 4Ć65..................
Figure 4Ć33:ăSubsequent 60 Hz Rejection Test Hookup 4Ć66...........
viii
Figure 4Ć34:ă60 Hz Rejection Test Result 4Ć67........................
Figure 4Ć35:ăLine Count Accuracy Test Hookup 4Ć68..................
Figure 4Ć36:ăLine Count Accuracy Test Setup Waveform 4Ć68..........
Figure 4Ć37:ăLine Count Accuracy Correct Result Waveform 4Ć69.......
Figure 4Ć38:ăPG502 Setup for Sync Duty Cycle Test 4Ć71..............
Figure 4Ć39:ăSync Duty Cycle Test: OneĆDiv eg Pulse Waveform 4Ć72..
Figure 4Ć40:ăSync Duty Cycle Test: Critically Adjusted Pulse 4Ć73.......
Figure 5Ć1:ăAccessing the Protection Switch 5Ć8.....................
Figure 5Ć2:ăHookup for Probe Compensation 5Ć10....................
Figure 5Ć3:ăPerforming Probe Compensation 5Ć11....................
Figure 5Ć4:ăProper and Improper Probe Compensation 5Ć11...........
Figure 5Ć5:ăExposing the Inner Probe Tip 5Ć12........................
Figure 5Ć6:ăInitial Test Hookup 5Ć12.................................
Figure 5Ć7:ăExposing the Probe Body 5Ć14...........................
Figure 5Ć8:ăInitial Test Hookup 5Ć15.................................
Figure 5Ć9:ăLocations of P6139A Probe Adjustments 5Ć17..............
Figure 5Ć10:ăAdjustments versus FrontĆCorner Response 5Ć17.........
Figure 5Ć11:ăTDS 620A/640A Five and Ten Percent Luminance
Patches 5Ć19..................................................
Figure 5Ć12:ăTDS 644A Five and Ten Percent Luminance Patches 5Ć22..
Figure 6Ć1:ăExternal Modules 6Ć12..................................
Figure 6Ć2:ăOuterĆChassis Modules 6Ć13.............................
Figure 6Ć3:ăInnerĆChassis Modules - TDS 620A or 640A with
A20 Display Assembly 6Ć14.....................................
Figure 6Ć4:ăInnerĆChassis Modules - TDS 644A with A30
Display Assembly 6Ć15.........................................
Figure 6Ć5:ăKnob Removal 6Ć18....................................
Figure 6Ć6:ăLine Fuse and Line Cord Removal 6Ć19...................
Figure 6Ć7:ăRear Cover and Cabinet Removal 6Ć22....................
Figure 6Ć8:ăFront Cover, Trim Ring, Menu Buttons, and Attenuator
Panel Removal (Front Cover not Shown) 6Ć23.....................
Figure 6Ć9:ăA12 FrontĆPanel Assembly Removal 6Ć26..................
Figure 6Ć10:ăDisassembly of FrontĆPanel Assembly 6Ć27...............
Figure 6Ć11:ăCabinet Modules Removal 6Ć30.........................
Figure 6Ć12:ăAttenuator Interconnect Cable Routing and
Jack Locations 6Ć32...........................................
Figure 6Ć13:ăA14 D1 Bus and AnalogĆPower and DigitalĆPower
Cables Removal 6Ć33..........................................
Figure 6Ć14:ăRemove Circuit Board Assembly From Oscilloscope 6Ć35..
Figure 6Ć15:ăRemove Circuit Board From Assembly 6Ć36..............
Figure 6Ć16:ăCircuit Board Installed 6Ć38.............................
Figure 6Ć17:ăProper Routing of the Video Cable 6Ć39..................
Figure 6Ć18:ăCircuit Board Removal 6Ć40............................
Figure 6Ć19:ăA11 Processor/Display Removal 6Ć43....................
ix
Figure 6Ć20:ăBoard Bracket Removal 6Ć44...........................
Figure 6Ć21:ăA10 Acquisition Board Removal 6Ć47....................
Figure 6Ć22:ăFloppy Disk Removal 6Ć49.............................
Figure 6Ć23:ăRear Chassis Removal 6Ć51............................
Figure 6Ć24:ăA16 Low Voltage Power upply Removal 6Ć53............
Figure 6Ć25:ăDisplay Assembly Removal - TD 644A 6Ć55............
Figure 6Ć26:ăDisplay Assembly Removal - TD 620A and 640A 6Ć56...
Figure 6Ć27:ăDisplay Driver Board Removal 6Ć57......................
Figure 6Ć28:ăFront ubpanel Removal 6Ć59..........................
Figure 6Ć29:ăAccessing the Protection witch 6Ć64....................
Figure 6Ć30:ăPrimary Troubleshooting Procedure 6Ć65.................
Figure 6Ć31:ăModule Isolation Troubleshooting Procedure 6Ć67.........
Figure 6Ć32:ăA16 Low Voltage Power upply Module Isolation
Troubleshooting Procedure 6Ć68................................
Figure 6Ć33:ăPower upply Voltage Measurement Locations 6Ć70.......
Figure 6Ć34:ăColor (TD 644A) Display Troubleshooting Procedure 6Ć71.
Figure 6Ć35:ăHorizontal and Vertical ync ignals - Color Display 6Ć72.
Figure 6Ć36:ăA Video ignal with White, Black, and Blanking
Levels - Color Display 6Ć72....................................
Figure 6Ć37:ăMonochrome (TD 620A and 640A) Display
Troubleshooting Procedure 6Ć73................................
Figure 6Ć38:ăHorizontal and Vertical ync ignals - Monochrome
Display 6Ć74..................................................
Figure 6Ć39:ăA Video ignal with White, Black, and Blanking
Levels - Monochrome Display 6Ć74.............................
Figure 6Ć40:ăProcessor/Acquisition Troubleshooting Procedure 6Ć75....
Figure 6Ć41:ăProcessor/Front Panel Troubleshooting Procedure 6Ć76....
Figure 6Ć42:ăAttenuator/Acquisition Troubleshooting Procedure 6Ć77....
Figure 6Ć43:ăA11 DRAM Processor/Display Module (View of
Right ide) 6Ć78...............................................
Figure 6Ć44:ăA11 DRAM Processor/Display Module (View of
Upper Left Corner) 6Ć79........................................
Figure 6Ć45:ăA11 DRAM Processor/Display Module (View of
Lower Left Corner) 6Ć79........................................
Figure 6Ć46:ăA10 Acquisition Module (View of Lower Left Corner) 6Ć80..
Figure 9Ć1:ăBlock Diagram 9Ć2....................................
Figure 9Ć2:ăInterconnections 9Ć4...................................
Figure 10Ć1:ăExternal Modules 10Ć5.................................
Figure 10Ć2:ăOuterĆChassis Modules 10Ć7............................
Figure 10Ć3:ăInnerĆChassis Modules - A30 Display hown 10Ć9........
Figure 10Ć4:ăCables 10Ć11..........................................
Figure 10Ć5:ăFloppy Disk 10Ć13......................................
Figure 10Ć6:ăAccessories 10Ć14......................................
x
xi
TableĂ1Ć1:ăRecord Length versus Divisions per Record, Samples
per Division, and Sec/Div Sequence 1Ć3........................
TableĂ1Ć2:ăNominal Traits Ċ Signal Acquisition System 1Ć9...........
TableĂ1Ć3:ăNominal Traits Ċ Time Base System 1Ć10..................
TableĂ1Ć4:ăNominal Traits Ċ Triggering System 1Ć10..................
TableĂ1Ć5:ăNominal Traits Ċ Display System 1Ć11....................
TableĂ1Ć6:ăNominal Traits Ċ G IB Interface, Output orts, and
ower Fuse 1Ć11..............................................
TableĂ1Ć7:ăNominal Traits Ċ Mechanical 1Ć12........................
TableĂ1Ć8:ăWarranted Characteristics Ċ Signal Acquisition System 1Ć13.
TableĂ1Ć9:ăWarranted Characteristics Ċ Time Base System 1Ć14........
TableĂ1Ć10:ăWarranted Characteristics Ċ Triggering System 1Ć15......
TableĂ1Ć11:ăWarranted Characteristics Ċ Output orts, robe
Compensator, and ower Requirements 1Ć15....................
TableĂ1Ć12:ăWarranted Characteristics Ċ Environmental 1Ć16..........
TableĂ1Ć13:ăTypical Characteristics Ċ Signal Acquisition System 1Ć19...
TableĂ1Ć14:ăTypical Characteristics Ċ Time Base System 1Ć20.........
TableĂ1Ć15:ăTypical Characteristics Ċ Triggering System 1Ć20..........
TableĂ1Ć16:ăTypical Characteristics Ċ Data Handling and Reliability 1Ć22
TableĂ2Ć1:ă owerĆCord Conductor Identification 2Ć8..................
TableĂ2Ć2:ăEffects of Corrupted Data 2Ć10............................
TableĂ4Ć1:ăTest Equipment 4Ć14....................................
TableĂ4Ć2:ăDC Offset Accuracy (Zero Setting) 4Ć22....................
TableĂ4Ć3:ăDC Accuracy 4Ć27.......................................
TableĂ4Ć4:ăAnalog Bandwidth 4Ć30.................................
TableĂ5Ć1:ăCalibration Tests 5Ć3....................................
TableĂ5Ć2:ăAdjustments Required for Module Replaced 5Ć4...........
TableĂ5Ć3:ăAdjustments and Dependencies 5Ć4.....................
TableĂ5Ć4:ăTest Equipment, Fixtures, and Supplies 5Ć5...............
TableĂ5Ć5:ăG IB Board Configuration1 5Ć7..........................
TableĂ6Ć1:ăRelative Susceptibility to StaticĆDischarge Damage 6Ć3.....
TableĂ6Ć2:ăExternal Inspection Check List 6Ć6.......................
TableĂ6Ć3:ăInternal Inspection Check List 6Ć7........................
TableĂ6Ć4:ăTools Required for Module Removal 6Ć11...................
TableĂ6Ć5:ăNormal Supply Voltages (Measured on J26 and J27
on the A11 DRAM rocessor/Display Module) 6Ć69................
TableĂ6Ć6:ăNoĆLoad Supply Voltages (Measured on J5 and J6
on the A17 Main LV ower Supply Module) 6Ć69...................
TableĂ7Ć1:ăInternational ower Cords 7Ć1...........................
xii
xiii
& ' " !' '" %)* '& &'+ #%('"!& + % #%")
"% +"(% #%"''"! ! '" #%)!' '" ' ',! &"&"#&
& &'+ !"% '"! ##& '" "#%'"%& ! &%) #%&"!!
& '*" '% & ##% ! !(&
H&'' !'& !'+ "!'"!& "% #%'& '' "( %&(' !
'" ' $(# !' "% "'% #%"#%'+
H&'' !'& !'+ "!'"!& "% #%'& '' "( %&(' !
#%&"! !(%+ "% "&& "
& '*" '% & ##% "! $(# !'
H !'& #%&"! !(%+ ,% !"' '+ &&
& "! %& ' %! "% ,% '" #%"#%'+ !(! ' $(#-
!' '&
H !'& #%&"! !(%+ ,% '+ && &
"! %& ' %!
& &+ " ##%& ! !(&
''-!&') )&
& &+ "& ##% "! $(# !'
"'
%"'')
%"(! %'
'% !
% '"
!(
xiv
&%) " ' ""*! #%('"!& '" !&(% ,"(% #%&"! &', !
'" #%)!' '" '% ' "% $(# !'
"!!' '" '
" !"' #%"% !'%! &%) "% (&' !' " '& #%"(' (!&& !"'%
#%&"! # " %!%! %&' ! %&(&''"! & #%&!'
!%"(& )"'& +&' ' &)% #"!'& ! '& #%"(' " )" #%&"!
!(%, " !"' '"( +#"& "!!'"!& "% " #"!!'& * #"*% & "!
&"!!' #"*% "% % ")! #%"'') #!& &"%! "% %#!
" #"!!'&
& !'! '" "#%' %" #"*% &"(%
'' * !"' ##, "% '! '*! ' &(##, "!('"%& "%
'*! '% &(##, "!('"% ! %"(! #%"'') %"(! "!!.
'"! '%"( ' %"(!! "!('"% ! ' #"*% "% & &&!' "% &
&,&' "#%'"!
!
% %"(! '%"( ' #"*% "% "
)" '% &" #( ' #"*% "% !'" #%"#%, *% %#'
*% %' %"(! & ! )% , $( &%) #%&"! " '&
"% ! "!!'"!& '" ' !#(' "% "('#(' '% !& " '
'"(' ' #%"'') %"(! "!!'"! #%'& " '
% #"'!' &" -%& & !(& !"& ! "!'%"& '' ,
##% '" !&('"%&
& "!, ' #"*% "% ! "!!'"% &# "% ,"(% #%"(' & "!,
#"*% "% '' & ! "" "!'"!
" )" % -% (& "!, ' (& &# ! ' #%'& &' "% ,"(%
#%"(' ! * & !' ! ',# )"' %'! ! (%%!' %'!
!% "%
# " xv
! # #
# !
! ! $ # !
"
"
! #
#
xvi
This manual suits for next models
2
Table of contents
Other Tektronix Test Equipment manuals
Tektronix
Tektronix 7623A User manual
Tektronix
Tektronix TDS3000C Series User manual
Tektronix
Tektronix SC 502 User manual
Tektronix
Tektronix 067-0883-99 User manual
Tektronix
Tektronix TBS1000C Series User manual
Tektronix
Tektronix TDS 310 User manual
Tektronix
Tektronix TMT4 Use and care manual
Tektronix
Tektronix TDS2000C series User manual
Tektronix
Tektronix TBS2000 Series Operating and maintenance manual
Tektronix
Tektronix TBS2102 User manual
Tektronix
Tektronix 214 User manual
Tektronix
Tektronix DPO4000 Series User manual
Tektronix
Tektronix TDS3012C User manual
Tektronix
Tektronix 2205 User manual
Tektronix
Tektronix A621 User manual
Tektronix
Tektronix 2245A User manual
Tektronix
Tektronix P6960 User manual
Tektronix
Tektronix TDS3000B Series User manual
Tektronix
Tektronix TDS200 Series Operating and maintenance manual
Tektronix
Tektronix TDS2012 User manual
Popular Test Equipment manuals by other brands
Amptec Research
Amptec Research 640N Operation & maintenance manual
Cirris
Cirris CH+ Getting started guide
Velleman
Velleman HPG1MK2 User manual and information manual
KHN Solutions
KHN Solutions BacTrack owner's manual
Steril-Aire
Steril-Aire Enhanced UVC Kit Installation and operation instructions
Martindale Electric
Martindale Electric PD690SX instruction manual
