Teltonika UM6225 User manual

USB WiMAX modem
User Manual
Suitable for UM6225 & UM6235

LEGAL NOTICE
Copyright © 2011 TELTONIKA Ltd. All rights reserved. Reproduction, transfer, distribution or storage of
part or all of the contents in this document in any form without the prior written permission of
TELTONIKA Ltd is prohibited. The manufacturer reserves the right to modify the product and manual
for the purpose of technical improvement without prior notice.
Other product and company names mentioned herein may be trademarks or trade names of their respective
owners.
ATTENTION
Before using the device we strongly recommend reading this
user manual first.
Do not rip open the device. Do not touch the device if the
device block is broken.
All wireless devices for data transferring may be susceptible to
interference, which could affect performance.
The device is not water-resistant. Keep it dry.

Table of contents
LEGAL NOTICE....................................................................................................................................................................2
ATTENTION ........................................................................................................................................................................2
TABLE OF CONTENTS..........................................................................................................................................................3
SAFETY INFORMATION.......................................................................................................................................................4
PRODUCT OVERVIEW.........................................................................................................................................................5
INTRODUCTION..........................................................................................................................................................................5
PACKAGE CONTENTS ...................................................................................................................................................................5
SYSTEM REQUIREMENTS ..............................................................................................................................................................5
HARDWARE,LED'S AND CONNECTIONS ..........................................................................................................................................5
WEBUI OVERVIEW .............................................................................................................................................................6
CONNECTING TO THE WEBUI .......................................................................................................................................................6
WEBUI STRUCTURE....................................................................................................................................................................7
STATUS.....................................................................................................................................................................................7
FIREWALL .................................................................................................................................................................................8
Port forwarding ................................................................................................................................................................8
Mac filtering .....................................................................................................................................................................9
IP filtering .......................................................................................................................................................................10
Demilitarization zone .....................................................................................................................................................11
ADMINISTRATION.....................................................................................................................................................................11
Settings...........................................................................................................................................................................11
Firmware ........................................................................................................................................................................12
Password ........................................................................................................................................................................12
ABOUT...................................................................................................................................................................................12
TECHNICAL SPECIFICATION ..............................................................................................................................................13
ELECTRICAL,MECHANICAL &ENVIRONMENTAL..............................................................................................................................13

SAFETY INFORMATION
In this document you will be introduced on how to use a UM6225/UM6235 modem safely.
We suggest you to adhere to the following recommendations in order to avoid personal injuries
and or property damage.
You have to be familiar with the safety requirements before using the device!
To avoid burning and voltage caused traumas, of the personnel working with the device, please
follow these safety requirements.
The PC to which the device is connected, should satisfy LST EN
60950-1 standard. The device can be used on first (Personal
Computer) or second (Notebook) computer safety class.
Do not mount or serve device during a thunderstorm.
To avoid mechanical damages to the device it is recommended to transport it packed in a
damage-proof pack. While using the device, it should be placed so, that its indicating LEDs would
be visible as they inform in which working mode the device is and if it has any working problems.
Protection against overcurrents, short circuiting and earth faults should be provided as a
part of the building installation. To disconnect the device plug it off the USB (Universal Serial Bus)
port.
Signal level of the device depends on the environment in which it is working. In case the
device starts working insufficiently, please refer to qualified personnel in order to repair this
product. We recommend forwarding it to a repair centre or the manufacturer. There are no
exchangeable parts inside the device.

PRODUCT OVERVIEW
Introduction
Teltonika UM6225/UM6235 is a compact USB dongle offering high speed data rate
connectivity to WiMAX networks. It supports the IEEE 802.16e connection standard, thus it is
flexible and can be used in a set of different environments: the office, home, a public place or even
a bus or a car. In addition, our product uses a hostless solution, which makes it run evenly well on
different platforms with all the popular operating systems.
Package contents
UM6225/UM6235
WiMAX modem
Leaflet “Quick Start Guide”
Note: The provisioning information is provided by your service provider, thus the questions
regarding connection problems should be addressed to it.
Note: If any of the components are missing or damaged, please contact the retailer or
reseller from which this product was purchased.
System requirements
USB port
Windows XP, Windows Vista, Windows 7, MAC OS X, or most of the Linux-based operating
systems.
A web browser must have a flash player plug-in (version 10 or higher) to access the WebUI for
network configuration.
Hardware, LED's and connections
Two LED indicators show the state of the device.
Status LED –modem started successfully.
Activity LED –indicates data transfer.
USB modem LED

WebUI OVERVIEW
In this section you will be briefly introduced to our user interface.
Note: we use the tool tip system in our web user interface in order to show additional information.
To see this data hover your mouse cursor above the field. Also, if the frame of the field becomes
red, it usually means that the data in the field is incorrect, in this case look into the red tool tip for
more information.
Connecting to the WebUI
To connect to the configuration web page do the following steps:
1. Type 192.168.0.1 to your favorite internet browser. Skip the step 2 if the password is
disabled (default: disabled).
2. Window asking for authentication will pop up. Enter your username and password (default:
username: user, password: user) and press enter.
3. Status window will appear in a few seconds:
First page of WebUI

WebUI structure
Our modern web user interface provides you with all the tools needed within the four main pages:
Status, Firewall, Administration, About.
Status
Status page
Status page consists of 6 properties that define the current state of the UM6225/UM6235 modem:
1. Uptime –the time since the modem was plugged in.
2. Signal quality –the quality of a signal in percents (and decibels).
<30% poor
>30% <50% decent
>50% <90% good
>90% very good
Note: signal quality depends on the distance between your device and the base
station and other factors: interference with other devices, etc.
3. Signal strength –the strength of a signal in dBm.
4. External IP –IP which was assigned to your device by the base station.
5. MAC address –physical address of the WiMAX connection module.
6. BS MAC address - physical address of the base station.

Firewall
Firewall page lets you configure firewall settings to meet your requirements. It includes port-
forwarding, MAC filtering and IP filtering
Port forwarding
Port forwarding is the process of translating the address and port number of a packet to a new
destination. It is used to permit communications by external hosts with services provided within
local area network.
Follow these steps to add a port-forwarding rule:
1. Enable –check to enable the Port forwarding.
2. Press the +button.
Port forwarding form
3. The following port-forwarding rule creation window will pop-up. Choose a rule type (single
port or port range) and fill the fields in a window to define the rule. Here are the
explanations regarding the field data types:
Predefined rule –select from a list of the most common rules.
Name –the name of the rule that will be visible in the list of your defined rules.
External port from/to –external port range to be redirected to an internal port.
Internal port –port used by the destination device to receive data.
Protocol –the protocol with which the rule operates.
Destination IP –the address of the device to which all the data coming to the selected
external ports is forwarded to.
New port-forwarding rule window
3. Press OK button to accept the rule.
4. After adding all the rules that you needed, press Apply to save the rules to the
configuration.

Mac filtering
MAC filtering is a security access control method used to determine access to the network by
physical address.
Follow these steps to add a MAC filtering rule:
1. Enable –check to enable the MAC filtering.
2. Press the +button.
Mac filtering form
3. The following MAC filtering rule creation window will pop-up.
New MAC filtering rule window
Name –MAC filtering rule name.
MAC address –physical address that you want to block from connecting to
and/or through the modem.
4. Press OK to add the rule.
5. After adding all the rules that you needed, press Apply to save the rules to the
configuration.

IP filtering
IP filtering is a security access control method used to determine access to the network by IP
address.
Follow these steps to add an IP filtering rule:
1. Enable –check to enable the IP filtering.
2. Press the +button.
IP filtering form
3. The following IP filtering creation rule window will pop-up.
New IP filtering rule window
Name –IP filtering rule name.
IP address –IP address that you want to block from connecting to and/or
through the modem.
4. Press OK to add the rule.
5. After adding all the rules that you needed, press Apply to save the rules to the
configuration.

Demilitarization zone
In computer networks, a DMZ (demilitarized zone) is a computer host or small network inserted as
a "neutral zone" between a private network and the outside public network.
DMZ page
To set up DMZ, click the Enable checkbox and put in IP address of your destination in the
Destination IP text field.
Administration
Administration page allows you to change the language of the WebUI, disable radio connection,
reboot the modem, save firmware to your computer (in a binary file format) or update it with a
newer version.
Settings
Settings page
Language –select a language from the drop down list.
Radio state –disables or enables radio (WiMAX) connection.
Reboot button –click to reboot this device. You will have to wait for a few seconds until it boots up
again.

Firmware
Firmware page
To save firmware: click Save firmware to file and at the following dialog browse to the directory
you want to place the binary file.
To update firmware: click Select firmware file and at the following dialog window select the
firmware file (note: file must be named firmware.bin). To start updating click: Update firmware.
This process usually takes 5 to 10 minutes.
Note: A firmware backup is only suitable for the device from which it was downloaded. If a
firmware backup is uploaded to another modem, that modem will malfunction.
Password
To set up or change a password check Enable user password and write a new one into two fields
bellow. To disable user password simply uncheck Enable user password checkbox. You must click
Apply if you want to save any of these to configuration.
About
About page
The About page displays the versions of your firmware and software that are currently running on
your device. This helps you decide whether or not you need to update your firmware.
Note: The last part in the OS version string refers to the sector size (64 kilobytes in this case) of the
flash memory. It is important that the firmware you update is made for the same flash sector size
as the flash memory in the device.

TECHNICAL SPECIFICATION
Standard Compliant IEEE 802.16e-2005
Air Interface S-OFDMA
Frequency Band 2.5-2.7GHz (UM6225) or 3.3-3.6GHz (UM6235)
Channel Bandwidth 3 MHz, 3.5 MHz, 5 MHz, 6 MHz, 7 MHz, 8.75 MHz and 10 MHz
Modulation Adaptive QPSK, 16QAM, 64QAM
MIMO MRC, Matrix A + MRC, Matrix B
Beamforming All I/O Beamforming Items
RF Output Power 2x20 dBm @ 2.5-2.7GHz; 2x17dBm @ 3.3-3.6GHz
RX Sensitivity:
QPSK1/2: -99.5 @ 2.5 GHz and 10 MHz BW
16QAM1/2: -94.29 @ 2.5 GHz and 10 MHz BW
QPSK1/2: -99 @ 3.5 GHz and 10 MHz BW
16QAM1/2: -93.8 @ 3.5 GHz and 10 MHz BW
Antenna Gain >2.5 dBi @ 2.6 GHz, >1.2 dBi @ 3.55 GHz
Antenna Type Internal Omni-Directional
Handover Hard / Optimized Handover
QoS Mechanism UGS, Real-Time-VR, Non Real-Time-VR, Best Effort, ERT-VR
Authentication EAP-TLS, EAP-TTLS-MSCHAPv2
Encryption 3 CCM-Mode 128-bit AES
Error Handling HARQ UL and DL, up to Category 7
Throughput 40 Mbps Total DL + UL
OS Support Windows XP/Vista/7, Linux, MAC OS
Installation CD-free, Self Install
LEDs Link Status and Link Activity
Software Hostless Operation
Electrical, Mechanical & Environmental
Dimensions (H x W x D) 93mm x 27mm x 10mm
Weight 21g
Power Supply USB
Power Consumption < 2.5W
Operating Temperature 0º to 50º C
Storage temperature -20º to 70º C
Operating Humidity 10% to 90% Non-condensing
Storage humidity 5% to 95% Non-condensing