TEMPLE & WEBSTER SBMETVWH User manual

ASSEMBLY INSTRUCTIONS
www.templeandwebster.com.au
SBMETVWH
SBMETVNT
Memo Entertainment Unit

Keep these instructions for future reference
Read these instructions and follow steps carefully to ensure you assemble the product
correctly and avoid damages. Check that all parts and hardware have been provided
before assembling the product. Place all contents on a clean, soft-flat surface to avoid
scratching the product.
CAUTION:
Only Tighten bolts to 80% at first. Once all parts have been assembled, fully tighten all
hardware. To prevent damage to threads, do not use a power tool and do not overtighten
bolts. Use two people to lift and turn the product when assembling. Do not attempt with
only one person and do not roll on to legs. Keep all hardware and small parts away from
children.
We recommend furniture be assembled near where they will be placed, to avoid moving
the product unnecessarily once assembled.
If there is a need to move the furniture, please remove all loose items and have extra
hands to help lift the furniture to the desired location. Dragging the furniture will damage
both the furniture and the floor.
Regularly check and re-tighten (if necessary) all bolts on furniture that you have
assembled yourself.
Wipe clean with a damp cloth. Use only water or a gentle detergent.
Wipe dry with a clean cloth.
Care and Maintenance of your Furniture
2
WARNING:
Do not stand on the Entertainment Unit !

3
WARNING：
- Walls are constructed from different materials, for example, masonry (solid brick) or
plasterboard lined cavity walls (hollow). It is important that you use the appropriate
wall fixings for your wall type. If unsure, please seek professional advice on how to
attach this safety strap to your specific wall.
- Your local hardware store will have the necessary drills and fixings and can offer
advice if needed. If in doubt, engage the services of a qualified tradesperson to install
and anchor the product.
It is STRONGLY RECOMMENDED that you ANCHOR this product.
Toppling furniture can cause serious injuries and death.
This product has been s with a strap. To prevent your furniture from tipping
forward it is strongly recommended that you securely attach this product to a wall or
other solid surface, using the straps provided and appropriate fixings.
IMPORTANT:
Regularly check that anchors are securely maintained.
Use safety drawer locks to prevent children climbing.
Stability of tall items may be affected by thick pile carpet or uneven floors.
Do not place unanchored televisions on furniture.
CAUTION:
For your safety when attaching the anchor fixings, please note the following:
- Check for any electrical wires or plumbing inside the wall before drilling any holes (if
you are unsure, please seek professional advice from a qualified tradesperson)

Tools Required
Parts List
DO NOT USE
Time Required
30 min
(P1). Top panel, x1
(P2). Bottom panel, x1
(P3). Left side panel, x1
(P4). Right side panel, x1
(P5). Divider, x1
(P6). Front support rail, x1
(P7). Back panel, x2
(P8). Base long support rail, x2
(P9). Base short support rail, x3
(P10). Door, x1
(P11). Door, x1
(P12). Door, x1
(P13). Door, x1
4
(P1)
(P2)
(P3)
(P4)
(P5)
(P6)
(P7)
(P7)
(P8)
(P8)
(P9)
(P9)
(P9)
(P10)
(P11)
(P12)
(P13)

T
wall
5
4pcs
8sets
45pcs 45pcs Hinge
Hinge
12 3 4
56 7 8
9 10

1
6
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
2
x 2
X11 X11
Screw 12 x Cam bolts (1) into 2x Base long support rails (P8) using a screwdriver as shown.
Position 2x Base long support rails (P8) to 3x Base short support rails (P9).
Insert 12 x Cam nuts (2) into 3x Base short support rails (P9), use a screwdriver to turn clockwise to lock.
Screw 11 x Cam bolts (1) into Bottom panel (P2) using a screwdriver as shown.
Position the Base frame onto Bottom panel (P2).
Insert 11 x Cam nuts (2) into the base frame, use a screwdriver to turn clockwise to lock.
With help, turn the assembled base over.
12
1
2
(P8)
(P8)
(P8)
(P9)
(P9)
(P9)
12
(P2)
(P2)
(P8)
(P9)
1
2

3
4
7
Screw 6 x Cam bolts (1) into Bottom panel (P2) using a screwdriver as shown.
Insert 6 x Dowels (3) into Bottom panel (P2).
Position Divider (P5) onto Bottom panel (P2).
Insert 2 x Cam nuts (2) into Divider (P5).
Use a screwdriver to turn Cam nuts (2) clockwise to lock.
13
(P2)
13
2
2
(P2)
(P5)

5
6
8
Screw 2 x Cam bolts (1) into Front support rail (P6) using a screwdriver as shown.
Position Front support rail (P6) to Divider (P5).
Insert 2 x Cam nuts (2) into Divider (P5), use a screwdriver to turn clockwise to lock.
Screw 4 x Cam bolts (1) into Left side panel (P3) and Right side panel (P4) using a screwdriver as shown.
12
1
2
(P5)
(P6)
(P6)
1
(P3)
(P4)
1
1

7
8
9
X8
Position Left side panel (P3), Right side panel (P4) onto Bottom panel (P2).
Gently attach Left side panel (P3) and Right side panel (P4) to Front support rail (P6) as shown.
Insert 8 x Cam nuts (2) into Left side panel (P3), Right side panel (P4) and Front support rail (P6).
Use a screwdriver to turn clockwise to lock.
(P6)
(P3)
(P3)
(P4)
(P2)
(P6)
2
(P6)
(P3)
(P4)
2

9
10
10
Insert 2x Back panels (P7) into the grooves of Left side panel (P3), Right side panel (P4), Divider (P5)
and Bottom panel (P2).
Screw 10 x Cam bolts (1) into Top panel (P1) using a screwdriver as shown.
Fix the 2x Wall straps (8) with 2 x Screws (10) and 2 x Washers (9) to the Top panel (P1) as shown.
(P7)
(P7)
(P3)
(P4)
(P5)
(P2)
1 8 910
(P1)
1
8
9
10

11
12
11
Attach 4x Hinges (4) to Door (P10) and (P13) with 8x Screws (6) using a screwdriver as shown.
Attach 4x Hinges (5) to Door (P11) and (P12) with 8x Screws (6) using a screwdriver
Insert 6 x Dowels (3) into Left side panel (P3), Divider (P5) and Right side panel (P4) as shown.
Position Top panel (P1) onto the assembled frame.
Insert 10 x Cam nuts (2) into Left side panel (P3), Right side panel (P4), Divider (P5) and Front support rail (P6).
Use a screwdriver to turn clockwise to lock.
23
(P1)
(P3)
(P5)
(P4)
2
3
(P11) / (P12)
(P10 / (P13)
45 6
6
4
6
5

13
12
IIIIII
IIIIII
IIIIII
If necessary, adjust the Hinges (4) and (5) using a Screwdriver.
Attach the 2 x Doors (P10) and (P13) to Left side panel (P3) and Right side panel (P4) with 16 x Screws (6) using
a screwdriver as shown.
Attach the 2 x Doors (P11) and (P12) to Divider (P5) with 16 x Screws (6) using a screwdriver.
6
(P3)
(P4)
(P5)
(P10)
(P11)
(P13)
6
6

14
13
X8
Fix 8x Back panel holders (7) to assembled unit with 8x Screws using a screwdriver.
15
wall
Move the ETU into position against a wall.
Mark suitable positions for the wall fixings.
Follow instructions to install the wall fixings onto the wall.
Reposition the ETU and fix the Wall straps (8) and 2 x Washers (9) to the wall with wall fixing.
Assembly is complete.
7
7
9