TEMPLE & WEBSTER Charlie SBC8DMGN User manual

ASSEMBLY INSTRUCTIONS
SBC8DMGN
Charlie 200x100cm glass dining table
Two people required
TEMPLE
WEBSTER
www.templeandwebster.com.au
2021/9/9

Keep these instructions for future reference
Assemble the furniture on a soft level surface to avoid damaging the furniture or
your floor.
Parts of the assembly will be easier with 2 people.
We recommend furniture be assembled near where they will be placed, to avoid
moving the product unnecessarily once assembled.
If there is a need to move the furniture, please remove all loose items and have
extra hands to help lift the furniture to the desired location. Dragging the
furniture will damage both the furniture and the floor.
Regularly check and re-tighten (if necessary) all bolts on furniture that you have
assembled yourself.
2
Care and Maintenance of your Furniture
W
Glass Warning
Keep these instructions for future reference
If the glass is chipped or broken, stop using the product and consult the seller.
WARNING
Do not place very hot or cold items on the glass surfaces unless adequate thick table
mats are used to prevent such items from coming in contact with the glass.
Do not sit or stand upon the glass surfaces.
Do not use the glass as a chopping surface.
Do not strike the glass with hard or pointed items.
When cleaning the glass panels use a damp cloth with washing up liquid or soft soap
if necessary, do not use washing powders or any other substances containing abrasives
since these substances scratch glass.
ipe clean with a damp cloth. Use only water or a gentle detergent.
Wipe dry with a clean cloth.

3
Tools Required Time Required
30 min
DO NOT USE
People Required
Parts List
Glass Top (P1);
Leg (P2) x 4.
(P1)
(P2)
(P2)
(P2)
(P2)

Hardware/Fittings
4
Leg Bracket x 1
(H1)
Bracket Top Cover x 1
(H2)(H3)(H4)
Bracket Bottom Cover x 1 M8x16mm Bolt x 12
M8x10mm Bolt x 16
(H5)
M8x50mm Bolt x 1
(H6)
Spring Washer x 29
(H7)
Washer x 29
(H8)
6mm Allen Key x 1
(H9)
50x50x3mm Felt Pad x 8
(H10)

5
1
2
Loosely attach 4 x Legs (P2) to Leg Bracket (H1) with 12 x Bolts (H4), 12 x Spring Washers (H7) and 12 x Washers
(H8) using Allen Key (H9).
H4 x 12H1 x 1 H7 x 12 H8 x 12 H9 x 1
H10 x 8
Paste 8 x Felt Pads (H10) to the 4 x Legs (P2).
With help, carefully place the leg assembly onto Glass Top (P1).
Loosely attach the Glass Top (P1) to the leg assembly with 16 x Bolts (H5), 16 x Washers (H8)
and 16 x Spring Washers (H7) as shown.
H1
H10
H10
H10
H10
P2
P1
P2
P2
P2
P2
H1
H4
H4
H4
H5
H7
H7
H8
H8
H5
H7
H8
H9
H9
H5 x 16 H7 x 16 H8 x 16 H9 x 1

8
3
4H6 x 1
H6
H7
H8
H9
H2 x 1 H3 x 1 H7 x 1 H8 x 1 H9 x 1
Fully tighten all Bolts (H4) and (H5) with Allen Key (H9).
H9 x 1
Fix the Bracket Top Cover (H2), and the Bracket Bottom Cover (H3) onto the Leg Bracket (H1) with 1 x Bolt (H6),
Spring Washer (H7) and Washer (H8) as shown.
Tighten the bolt with Allen Key (H9).

5
6
Assembly is complete.
With help,carefully turn the table over.
7
Please dispose of all
packaging thoughtfully.