TEMPLE & WEBSTER FJNODKWH User manual

2 PERSON RECOMMENDED
A
14 PCS
G
9 PCS
B
6 PCS
C
15 PCS
D
15 PCS
E
17 PCS
F
17 PCS
1
2
3

5
4
Read these instructions and follow steps carefully to ensure you assemble the product correctly and avoid damages. Check
that all parts hardware have been provided before assembling the products. Place all contents on a clean, soft-flat surface to
avoid scratching the product.
CAUTION:
Only tighten bolts to 80% at first. Once all parts have been assembled, fully tighten all hardware. To prevent damage to threads,
do not use a power tool and do not over tighten bolts.
Use two people to lift and turn the product when assembling.
Do not attempt with only one person and do not roll on to legs. Keep all hardware and small parts away from children.
8
8
11
9
10
10
7
6

2
Step 1:
Step 2:
Attach 3 x Cam Bolts (C) to Panel (4) as shown. Tighten with a Phillips Head Screwdriver.
Attach 2 x Cam Bolts (C) to Panel (2) as shown. Tighten with a Phillips Head Screwdriver.
FLIP
4
4
CAUTION:
Only tighten bolts to 80% at first. Once all parts have been assembled, fully tighten all hardware. To prevent damage to threads,
do not use a power tool and do not over tighten bolts.
Use two people to lift and turn the product when assembling.
Do not attempt with only one person and do not roll on to legs. Keep all hardware and small parts away from children.
C
C
C
C
C

2
Attach 4 x Cam Bolts (C) to Panel (10) as shwon.
Insert 4 x Cam Nuts (D) into the holes of Panel (9).
Rotate the cam nuts so the arrows point towards the
incoming cam bolts. Attach Panels (10) into place and
tighten the cam nuts.
x2
Step 3:
Step 4:
Insert 2 x Dowels (A) into Panel (9). Push 4 x Bolts (E) through Panel (2) and insert 4 x Nuts (F)
into Panels (8, 10). Rotate the nuts so the opening point towards the incoming bolts.
Attach Panels (8, 9, 10) to Panel (2) by
tightening with the Phillips Head Screwdriver. Attach 4 x
hole stickers (G) to Panel (2).
C
D
F
F
F
E
E
E
E
E
F
D
D
D
C
√
×
9
9
10
10
10
A
A
10
10
8
8
G
G
G
G
G
D

2
Insert 2 x Dowels (A) into Panel (11) as shwon. Insert 2 x Cam Nuts (D) into the holes
of Panel (11). Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Panel (11) into place and tighten the cam nuts.
Insert 4 x Dowels (A) into
Panesl (9, 11). Push 4 x
Bolts (E) through Panel (4)
and insert 4 x Nuts (F) into Panels (8, 10). Rotate the nuts so the opening point towards the incoming
bolts. Attach Panel (4) to Panels (8, 9, 10) by
tightening with the Phillips Head Screwdriver. Insert 2 x
Cam Nuts (D) into the holes
of Panel (11). Rotate the cam nuts so the arrows point towards the incoming
cam bolts. Push Panel (11) into place and tighten the cam nuts.
Step 5:
Step 6:
E
E
E
E
11
A
D
D
A
F
F
F
D
DF
A
AA
A
4
11
A
D
8
8
9
10
10

2 PERSON RECOMMENDED
Step 7:
Step 8:
3
Push 4 x Bolts (E) through Panel (4) and insert 4 x Nuts (F) into Panels (5, 6). Rotate the nuts so the
opening point towards the incoming bolts. Attach Panel (4) to Panels (5, 6) by
tightening with the Phillips
Head Screwdriver.
Insert 1 x Cam Nut (D) into the holes of Panel (7). Rotate the cam nuts so the arrows
point towards the incoming cam bolts. Push Panel (7) into place and tighten the cam nuts.
Push 5 x Bolts (E) through Panel (3) and insert 5 x Nuts (F) into Panels (5, 6, 7). Rotate the nuts so the
opening point towards the incoming bolts. Attach Panel (3) to Panels (5, 6, 7) by
tightening with the
Phillips Head Screwdriver. Attach 5 x hole stickers (G) to Panel (3) as shown.
E
E
F
E
F
E
E
F
F
E
E
EE
F
F
D
FF
4
G
G
G
G
G
5
76
5
7
6

Step 9:
Step 10:
3
Attach 6 x Cam Bolts (C) to Panel (1). T ighten with the Phillips Head Screwdriver.
Insert 6 x Dowels (A) into Panels (2, 3, 4). Insert 6 x Cam Nuts (D) into the holes of Panels (2, 3, 4).
Rotate the cam nuts so the arrows point towards the incoming cam bolts. Push Panel (1) into place
and tighten the cam nuts. Attach Panel (1) to Panels (2, 3, 4) with 6 x Screws (B).
T ighten with the
Phillips Head Screwdriver.
D
DD
D
C
B
B
B
B
C
C
CC
C
B
B
4
1
1
2
7
8
8
A
A
A
A