Tennsco 1-Wide Welded Base for Lockers without Legs Instruction Manual

PK-2660619
ASSEMBLY INSTRUCTIONS & PARTS MANUAL
1-Wide or 3-Wide Welded Base
for Lockers without Legs
RETAIN INSTRUCTIONS FOR FUTURE REFERENCERETAIN INSTRUCTIONS FOR FUTURE REFERENCE
T ennsco LLC., Dickson, TN 37056-1888 • [phone]
GENERAL SAFETY INFORMATIONGENERAL SAFETY INFORMATION
Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.
For safety, wear a pair of work gloves when assembling or performing any maintenance on units.
LIMITED WARRANTYLIMITED WARRANTY
Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply in
the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during
shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:
a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:
b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO
EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the
goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty
and are returned within the warranty period stated above.

ATTACHMENT OF 1-WIDE WELDED LOCKER BASE
1. Securely mount the locker base to the oor. (Please use your
local codes when mounting your unit. Codes may vary due
to location.)
Two people required for assembly. Approximate assembly time: 5-10 minutes.
2. With help from an associate, lift the unit at an angle and
lock the front part of the unit in to the anges of the base.
3. In order to lock in the anges, allow the front part of
the unit to slip underneath the anges on the base.
Make sure that the unit is lined up with the base, with
no excess sides hanging over the base.
4. Bolt two tech screws through the bottom shelf of
the locker.


When Anchoring a 1-Wide Unit to the Floor:
When Anchoring a 1-Wide Unit
to the Wall or Another Locker:

1. Lay the locker on it’s side. Use a tarp or cloth as a surface to
ensure that the unit is not scratched.
2. Attach the base by sliding the base over the top of the anges
on the bottom part of the unit to lock it into place.
3. Bolt two tech screws
through the bottom shelf
of the locker.
4. With help from an associate, lift the locker
to the initial upright position. Finish by
securing the locker to the wall or to the
next locker.
When Anchoring a 1-Wide Unit
to the Wall or Another Locker:
When Anchoring a 3-Wide Unit to the Floor:
1. Securely mount the locker base to the oor. (Please use your
local codes when mounting your unit. Codes may vary due
to location.)
2. With help from an associate, lift the unit at an angle and
lock the front part of the unit in to the anges of the base.


3. In order to lock in the anges, allow the front part
of the unit to slip underneath the anges on the
base. Make sure that the unit is lined up with the
base, with no excess sides hanging over the base.
4. Bolt two tech screws through the bottom shelf
of the locker.

1. Lay the locker on it’s side. Use a tarp or cloth as a surface to
ensure that the unit is not scratched.
2. Attach the base by sliding the base over the top of the anges
on the bottom part of the unit to lock it into place.
3. Bolt two tech screws
through the bottom shelf
of the locker.
4. With help from an associate,
lift the locker to the initial
upright position. Finish by
securing the locker to the
wall or to the next locker.
When Anchoring a 3-Wide Unit
to the Wall or Another Locker:
49B267