Texas Instruments TUSB3200EVM2 User manual

6ĆChannel TUSB3200EVM2
for the TUSB3200A USB
Streaming Data Controller
January 2003 Digital Audio
User’s Guide
SLAU062A

IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
ordersandshouldverifythatsuchinformationiscurrentandcomplete.AllproductsaresoldsubjecttoTI’sterms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TIdoesnotwarrantorrepresentthatanylicense, eitherexpress orimplied, isgranted underanyTIpatentright,
copyright,maskworkright,orotherTIintellectualpropertyrightrelatingtoanycombination,machine,orprocess
inwhichTIproductsorservicesareused.InformationpublishedbyTIregardingthird–partyproductsorservices
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Mailing Address:
Texas Instruments
Post Office Box 655303
Dallas, Texas 75265
Copyright 2003, Texas Instruments Incorporated

Related Documentation From Texas Instruments
iii
Read This First
Preface
Read This First
About This Manual
This user’s guide describes the setup and operation of the TUSB3200EVM2
platform.
How to Use This Manual
This document contains the following chapters:
- Chapter 1—Equipment
- Chapter 2—Detailed Description of the TUSB3200EVM2
- Appendix A—Schematic Diagrams
Related Documentation From Texas Instruments
TUSB3200A Literature Number SLES018
TLV2362 Literature Number SLOS195A
TPS7233QD Literature Number SLVS102G
CS4228 www.crystal.com for product detail information
FCC Warning
Thisequipmentisintendedforuseinalaboratorytestenvironmentonly.Itgen-
erates,uses,andcanradiateradiofrequencyenergyandhasnotbeentested
for compliance with the limits of computing devices pursuant to subpart J of
part 15 of FCC rules, which are designed to provide reasonable protection
against radio frequency interference. Operation of this equipment in other en-
vironmentsmaycauseinterferencewithradiocommunications,inwhichcase
the user at his own expense will be required to take whatever measures may
be required to correct this interference.

iv

Running Title—Attribute Reference
v
Contents
Contents
1 Equipment 1-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 Hardware 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1.1 EEPROM Evaluation (Internal Mode) 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1.2 In-Circuit Emulator (ICE) Evaluation 1-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Detailed Description of the TUSB3200EVM2 2-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 TUSB3200EVM2 Setup 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Interfaces and Ports 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 Power Supplies 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4 Light Emitting Diode (LED) 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5 Jumpers 2-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6 Complete Analog Stage 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7 EEPROM 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.8 TUSB3200A Development Tool Recommendations 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.9 TUSB3200EVM2 Design Platform Schematic/Layout 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figures
1–1 TUSB3200EVM2 Design Platform Equipment 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tables
1–1 Jumpers Set Up for Internal Mode 1-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2–1 Jumpers and Switches 2-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

vi

1-1
Equipment
Equipment
This user’s guide describes the setup and operation of the TUSB3200EVM2
platform.ThisPCB contains two main activeparts:TUSB3200ASTC(TIUSB
streamingcontroller)andcrystalCS4228codec.ThisPCBisreferredtoasthe
TUSB3200EVM2 from this point on. Familiarity with emulator hardware and
software is required and assumed throughout this user’s guide.
Topic Page
1.1 Hardware 1-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1

Hardware
1-2
1.1 Hardware
Figure 1–1 shows the equipment necessary to perform evaluation of the
TUSB3200EVM2.
Figure 1–1.TUSB3200EVM2 Design Platform Equipment
USB EVM2
The TUSB3200EVM2 hardware platform measures 6.0′′ X 5.5′′ (W ×L).
Throughout this document text inside of parentheses (ex.) represents
reference designators that identify components located on the
TUSB3200EVM2.
The hardware setup for the TUSB3200EVM2 can be accomplished by two
separate methods—EEPROM evaluation and in-circuit emulator (ICE)
evaluation.UseoftheEEPROMinstalledon theboardisrecommendedwhen
performing a quick initial check to verify if the board works properly. The
respective evaluation procedures are detailed in the following section.
1.1.1 EEPROM Evaluation (Internal Mode)
The TUSB3200EVM2 comes with a preprogrammed EEPROM. This
EEPROM is inserted in the 8-pin DIP socket. The jumper configuration for the
internalmode is listed inTable 1–1.Usethefollowingprocedurefor EEPROM
evaluation:
- Set J8 to position 1–2 to bus-power the TUSB3200EVM2; set J8 to 2–3
to put the TUSB3200EVM2 in self-powered mode (a power supply is
required).
- In self-powered mode, a single 9-V dc at 500-mA supply must be
connected to the power terminals 9V and ground (GND) of the
TUSB3200EVM2. Once the board is powered, GPIO, and the LEDs
should turn on, and the power drawn from the supply should not exceed
the USB specification of 500 mA.
- Connect a USB cable from the root hub of the PC to type-B connector J1
on the EVM. This should start the USB enumeration on a host PC.
Enumeration signals that a USB (audio) device has been detected by the

Hardware
1-3
Equipment
hostPCandthedeviceisreadytostreamaudioviaaUSB.Aspeakericon
should show up once the enumeration is complete. Double click this icon
to confirm that the USB is the preferred device for audio output; if not,
reconfigure the PC for USB audio output.
Table 1–1.Jumpers Set Up for Internal Mode
Jumper Position
JP1 Open
JP2 Open
JP3 Position 2–3
JP4 Open
JP5 Open
JP6 Open
JP7 Open
JP8 Position 2–3
JP9 Position 2–3
JP10 Position 2–3
JP11 Position 2–3
JP12 Position 2–3
JP13 Position 2–3
JP14 Open
JP15 Close
JP16 Open
JP17 Open
JP18 Open
1.1.2 In-Circuit Emulator (ICE) Evaluation
Use the following procedure for in-circuit emulator evaluation:
- Installtheemulator.RefertotherespectiveICEuser’sguidefortheemula-
tor.
- Attach emulator POD to TUSB3200EVM2 ICE Socket (J3). A 40-pin ex-
tension adapter may be required to allow enough clearance for access to
thebuttons,jumpers, and connectors. Pin 1 isdesignatedbyatriangleon
the opposite side of the J3 reference designator.

1-4

2-1
Detailed Description of the TUSB3200EVM2
Detailed Description of the TUSB3200EVM2
This chapter presents a detailed description of the TUSB3200EVM2.
Topic Page
2.1 TUSB3200EVM2 Setup 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Interfaces and Ports 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 Power Supplies 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4 Light Emitting Diode (LED) 2-2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5 Jumpers 2-3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6 Complete Analog Stage 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7 EEPROM 2-4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.8 TUSB3200A Development Tool Recommendations 2-4. . . . . . . . . . . . . . .
2.9 TUSB3200EVM2 Design Platform Schematic/Layout 2-4. . . . . . . . . . . . .
Chapter 2

TUSB3200EVM2 Setup
2-2
2.1 TUSB3200EVM2 Setup
TheTUSB3200EVM2is designed to allowdevelopmentand evaluation of the
TUSB3200A for multichannel applications. The USB controller (U1) accepts
USB data streams and generates output at the C-port, I2C port, and/or GPIO
port. A full explanation of how to configure the TUSB3200A to control the
streaming data and set up the interface ports and registers is contained in the
TUSB3200A data manual. A standard USB cable is required to connect the
EVM platform to a downstream port. The EVM uses a standard type-B
connector. Set JP8 to position 2–3 to send the MCLKO to the codec. Set JP3
to position 2–3 for normal mode operation; this action disables the external
interrupt signal to the TUSB3200A. Note that an arrow always designates
position1ofanyjumper.TheTUSB3200Amustbesettoexternalmodetouse
the in-circuit emulator. The TUSB3200EVM2 board is shipped in internal
mode.Forinternalmode,JP4isopenandJP15isclosed.Toswitchtoexternal
mode, simply move the jumper from JP15 to JP4.
2.2 Interfaces and Ports
The USB port interface is the only connection required for full operation. The
in-circuit emulator is required for the external emulator pad. All other
connections are used to increase further development and evaluation
functionality. The USB connector has four pins defined as VBUS (pin 1), D+
(pin 2), D–(pin 3), and GND (pin 4).
2.3 Power Supplies
The TUSB3200EVM2 board can be self-powered, or can use USB bus power
(when J8 is set to position 2–3). In the self-powered mode, the
TUSB3200EVM2 PCB requires a single positive 9-V dc supply at 500 mA. An
LM317EMP regulator is used to generate a steady 5-V dc supply. This 5-V dc
supply is connected to an onboard, low-dropout regulator to generate a 3.3-V
dc supply. In the USB bus-powered mode, connect one end of a USB cable
to the EVM board and another end of the cable to a PC root port.
2.4 Light Emitting Diode (LED)
A set of green and yellow LEDs is installed on the TUSB3200EVM2 board for
quickandeasyGPIOevaluation.ThegreenLEDsareconnectedtoport1 bits
0 through 7 of the in-circuit emulator for external mode. The yellow LEDs are
connected to port 1 bits 0 through 7 and port 3 bits 0, 1, and 3–5 of the
TUSB3200A for normal mode. Note that yellow LEDs illuminate in external
mode but are not GPIO functions and should not be treated as such.

Jumpers
2-3
Detailed Description of the TUSB3200EVM2
2.5 Jumpers
Table 2–1 provides jumper configurations for different modes of operation.
Table 2–1.Jumpers and Switches
Jumper/
Switch Description
JP1 Position 1–2 on: Ground CRESET; JP1.1 CRESET
JP2 Position 1–2 on: Ground CDATI; JP2.1 CDATI
JP3 Position 1–2:external interrupt enabled; Position 2–3:no external interrupt
JP4 Position 1–2 on:external mode; Position 1–2 off: internal mode
JP5 Position 1–2 on: Ground CDATO; JP5.1 CDATO
JP6 Position 1–2 on: Ground CSCHNE; JP6.1 CSCHNE
JP7 Position 1–2 on: Ground CSCLK; JP7.1 CSCLK
JP8 Position 1–2: MCLK to JP16.1; Position 2–3: MCLKO to CS4228
JP9 Position 1–2: CRESET to JP1.1; Position 2–3: CRESET to CS4228
JP10 Position 1–2: CDATI to JB2.1; Position 2–3: CDATI to CS4228
JP11 Position 1–2: CDATO to JP5.1; Position 2–3: CDATO to CS4228
JP12 Position 1–2: CSYNC to JP14.1; Position 2–3: CSYNC to CS4228
JP13 Position 1–2: CSCLK to JP7.1; Position 2–3: CSCLK to CS4228
JP14 Position 1–2: Ground CSYNC; JP14.1 CSYNC
JP15 Position 1–2 on: internal mode; Position 1–2 off: external mode
JP16 Position 1–2 on: Ground MCLKO; JP16.1 MCLKO
JP17 Do not jumper position 1–2; JP17.1 SDA
JP18 Do not jumper position 1–2; JP18.1 SCL
S1A GPIO P3.3 general-purpose momentary
button internal MCU mode
S2A GPIO P3.4 general-purpose momentary
button internal MCU mode
S3A GPIO P3.5 general-purpose momentary
button internal MCU mode
S1B GPIO P3.3 general-purpose momentary
button external MCU mode
S2B GPIO P3.4 general-purpose momentary
button external MCU mode
S3B GPIO P3.5 general-purpose momentary
button external MCU mode
J8 Position 1–2: Self-powered mode; Position 2–3: Bus-powered mode
Reset Reset EVM platform and in-circuit emulator (external mode)

Complete Analog Stage
2-4
2.6 Complete Analog Stage
A complete analog output stage is provided on the TUSB3200EVM2 platform
to eliminate the need for back-end development for evaluation purposes. The
analog stage includes a crystal CS4228 codec and line output amplifiers with
second-orderlow-passfiltersforall six channels. A line input and a lineoutput
are also provided.
2.7 EEPROM
The EEPROM is used to set up the TUSB3200EVM2. The EEPROM is
recommended to be 8K bytes to match the RAM memory size. Firmware for
the TUSB3200EVM2 must be loaded for correct operation. An 8-pin DIP
socket allows easy installation and removal of the EEPROM. TUSB3200A
automaticallydownloadsthedatafromtheEEPROM into memory and begins
executing code once the board is powered up and connected to the host via
the USB.
2.8 TUSB3200A Development Tool Recommendations
CheckthefollowingwebsitesforTUSB3200Adevelopmenttoolrecommenda-
tions:
8051/8052 Emulators
http://www.nohau.com EMUL51-PC/E128–16 and POD–C32–HF–42
http://www.signum.com USP–51E and POD51FX
http://www.phyton.com PICE–51 and P051–RX/FA and A051–D40
8051/8052 Code Development Tools
http://www.keil.com/c51/default.htm PK51 or DK51 or CA51 (price varies
with package)
2.9 TUSB3200EVM2 Design Platform Schematic/Layout
An electronic copy of the TUSB3200EVM2 schematic is available on the
TUSB3200EVM2 CD.