Titan SF1022 Installation manual

6kg SDS PLUS ROTARY HAMMER SF1022&SF26S6
SAFETY AND OPERATING MANUAL

GUARANTEE
This product carries a Screwfix Direct Ltd guarantee of 12 months. If your product
develops a fault within this period, you should,in the first instance contact Screwfix
Direct Ltd on Freephone 0500 41 41 41. If the fault occurs within the first 12 months,
you may return the goods for a full refund or we will repair or replace the goods if
you prefer. When repair is not practical or identical goods are not available, alternative
goods of similar specification and quality will usually be provided but, failing this, you
will be offered a partial or full refund depending on the time period since purchase.
This guarantee specifically excludes losses caused due to:
- Fair wear and tear
- Misuse or abuse
- Lack of routine maintenance
- Failure of consumable items (such as batteries)
- Accidental damage
- Cosmetic damage
- Failure to follow manufacturer’s guidelines
- Loss of use of the goods
- Repairs attempted by anyone, unless authorised by Screwfix Direct Ltd.
This guarantee does not affect your statutory rights. This guarantee is only valid in the UK.
For further technical advice, spare parts or repair service (outside of guarantee) please
contact the customer helpline number on 0845 607 6380.
Congratulations on your purchase of a power tool from Screwfix Direct
Ltd. We want you to continue getting the best performance from it so this
handbook includes information on safety, handling and care. Please retain this
handbook in case you need to refer to any of the information in the future.
Your power tool comes with a 12-month guarantee,so should it develop
a fault within this period contact Screwfix Direct Ltd on Freephone 0500 41
41 41.

6kg SDS PLUS ROTARY HAMMER SF1022&SF26S6
SAFETY INSTRUCTIONS
WARNING! Read all instructions. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
SAVE THESE INSTRUCTIONS
1. Work area.
a. Keep work area clean and well lit. Cluttered and dark areas invite
accidents.
b. Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2. Electrical safety.
a. Power tool plugs must match the outlet. Never modify the plug in
any way. Do not use any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat,oil,sharp edges
or moving parts. Damaged or entangled cords increase the risk of electric
shock.
e. When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f. Use a Residual Circuit Breaker on all 230V Power tools. This can help
minimise the risk of an electrical shock if an earth fault or short circuits occurs.
g. If using a power cable extension ensure that the cable is fully unwound
and that its length is less than 30m. Lengths over 30 m will effect the tools
performance as a result of voltage drop.
3. Personal safety.
a. Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal injury.
b. Use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used
for appropriate conditions will reduce personal injuries.
c. Avoid accidental starting. Ensure the switch is in the off-position
before plugging in. Carrying power tools with your finger on the switch or
plugging in power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool

on. A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your
hair, clothing and gloves away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used. Use
of these devices can reduce dust-related hazards.
4. Power tool use and care.
a. Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the rate for
which it was designed.
b. Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c. Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tools operation. If damaged, have the power tool repaired before
use.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc., in accordance with
these instructions and in the manner intended for the particular type of
power tool, taking into account the working conditions and the work to
be performed. Use of the power tool for operations different from intended could
result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
HEALTH ADVICE
WARNING! When drilling, sanding, sawing or grinding, dust particles will be
produced. In some instances, depending on the materials you are working with,
this dust can be particularly harmful to you (e.g. lead from old gloss paint).
You are advised to consider the risks associated with the materials you are working
with and to reduce the risk of exposure. You should:
-- Work in a well-ventilated area.

6kg SDS PLUS ROTARY HAMMER SF1022&SF26S6
-Work with approved safety equipment, such as those dust masks that are specially
designed to filter microscopic particles.
ADDITIONAL SAFETY RULES FOR YOUR SDS HAMMER
This is a powerful hammer. Caution needs to be observed when operating.
1.If the supply cord is damaged have it replaced by a qualified person.
2.Always wear a dust mask.
3.Dress in suitable overalls.
4.Safety boots are recommended at all times especially when using the chisel action.
5.Proper safety gloves are also recommended.
6.When using chisel a dust mask is necessary because of the dust created by the
action.
7.Wear ear protectors. Exposure to noise can cause hearing less.
8.This heavy duty high torque machine should not be used, while standing on a
ladder.
9.Watch out for the initial torque reaction of the drill, especially if the drill or chisel bit
becomes lodged in masonry.
10.Do not use damaged or worn drills.
11.Do not run the machine with any part of the casing missing or damaged.
12.Check walls for hidden electric cable, gas and electric pipe before you start any
drilling task.
13.Chisel bits and drill bits may be flung out of the machine accidentally and cause
serious injury.
14.Before starting to work, always check that the chisel or drill bit is properly locked
in the chuck.
15.Vibrations can injure the hand-arm system. Keep exposure to vibrations as short
as possible.
16.When carrying out work, always hold the drill with both hands and ensure that you
have a stable standing position.
17. Lubricating the gear box.The gear box must be lubricated after approximately 5
hours of use to ensure it works efficiently.A small container of grease is supplied with
the drill.Go to section “Maintenance“ for the details.
18. Always use the appropriate safety equipment that is required for the product. e.g.
Goggles / Safety Spectacles, Ear defenders (essential with tools with a noise rating of
over 85dB(A), Gloves and face masks. In all cases ensure that the safety equipment is
in good condition.
19. Ensure that if a side handle or stabilising handle is provided with the power tool
then these are adjusted into a comfortable position and that both handles are used to
securely grip the power tool when in use.
Double insulation:
The tool is double insulated. This means that all the external metal parts are electrically
insulated from the mains power supply. This is done by placing insulation barriers
between the electrical and mechanical components making it unnecessary for the tool
to be earthed.

SYMBOLS
Read the manual Warning Wear gloves
Wear dust mask,eye & ear protection
Conforms to relevant safety standards

6kg SDS PLUS ROTARY HAMMER SF1022&SF26S6
1. FASTENING SLEEVE
2. DIAL SELECTOR
3. GEAR BOX COVER
4. ON/OFF SWITCH
5. SAFETY BUTTON
6. LEVER SELECTOR
7. VARIABLE SPEED SWITCH
8. MAINS POWER CABLE
9. AUXILIARY HANDLE
10. DUST COVER
11. GEAR BOX COVER SPANNER
12. DEPTH GAUGE
13. GREASE POT
14. KEY CHUCK AND ADAPTER
15. SDS CHISEL BIT, 250mm (1 FLAT CHISEL, 1 POINT CHISEL )

TECHNICAL DATA
Voltage: 230V~50Hz
Input power: 1250W
No load speed: 0-800min-1
Hammer rate: 0-3200min-1
Drilling capacity Wood: 40mm
Steel: 13mm
Masonry: 32mm
Double insulation:
Weight: 5.9kg
NOISE AND VIBRATION DATA
Sound pressure level: 89dB (A)
Sound power level: 106dB (A)
Vibration level: 3.5m/s2
ACCESSORIES
Auxiliary handle 1pc
Grease pot 1pc
Gear box cover spanner 1pc
Depth gauge 1pc
Dust cover 1pc
16. CHUCK KEY
17.SDS DRILL BITS (8, 10, 12, 14, 16mm)
18. DIAMOND CORE (65mm,80mm)
19. DRILL BITS COATED TI(5,6, 8, 10, 12mm)
20. SDS DRILL BITS (6,8, 10, 12, 14, 16,18,20mm)
21. SDS CHISEL BIT, 250mm (1 FLAT CHISEL, 1 POINT CHISEL,1 “U” CHISEL)
Only for SF26S6
Key chuck and adapter 1 p c
SDS drill bits 5pcs
SDS Chisel bit 2pcs
Chuck key 1 p c
Only for SF1022
Diamond core 2pcs
SDS drill bits 8pcs
SDS Chisel bit 3pcs
Drill bits coated Ti 5pcs

6kg SDS PLUS ROTARY HAMMER SF1022&SF26S6
OPERATION INSTRUCTIONS
Familiarize yourself with the rotary hammer
before use.
Warning:Make sure the hammer is
isolated from the mains supply before
fitting accessories. Before undertaking any
maintenance or operations on the rotary
hammer isolate the plug from the 13 amp
socket.
1. FITTING THE AUXILIARY HANDLE
Attach the handle as shown in Fig2 depending on
being left handed or right handed.
To ensure the handle does not slip forward locate
the “lugs“ on top of handle into the grooves at
the front end of SDS drill.
2. FITTING SDS TOOLS OR CHUCK
The hammer is equipped with an SDS-plus
attachment system. The chuck/SDS tools have
slots in the shank. These locate with tabs in the
rotary hammer. Hold the rotary hammer with
one hand facing away from you. See Fig3.Grip
and pull back the fastening sleeve and insert the
chuck/SDS tool.Push inwards until a resistance is
felt. It may be necessary to spin the chuck/SDS
tool until the shaft drops completely into place.
Once you are satisfied it has seated release the
black fastening sleeve. This should lock the chuck
into position.
3.REMOVE SDS TOOL OR CHUCK
Pull back fastening sleeve, hold and remove tool/
chuck. See Fig3.
Note: The SDS tools or chuck will be gripped
firmly by its shank and will not be able to be
removed.
See Fig3. If the chuck/SDS tool is not located
repeat the installation operation again.
4.OPERATING THE SAFETY ON/OFF SWITCH
Your switch is locked off to prevent accidental
starting. Depress switch lock button then on/off
switch and release lock button (see Fig4). Your
switch is now on, to switch off just release the
on/off switch.
5.VARIABLE SPEED SWITCH
Fig 4
Fig 5
Fig 2
Fig 3
Tighten loosen
Grooves
Lugs

The speed increases as you turn the switch
towards the higher number and decreases on the
lower number. (See Fig 5)
6. USING THE KEY CHUCK
The hammer comes supplied with a 1.5-13mm
chuck, which is used for smaller drill bits. After
deciding if hammer or normal drilling is required
proceed with following instructions. Inserting
a drill bit into chuck. Before installing drill bit,
remove mains plug from mains supply.
Place chuck key into chuck, turn key anti-clockwise
to undo/loosen chuck insert drill/tool and firmly
tighten chuck by turning key clockwise. Remove
key and put in Blow Mould Case.(See Fig 6)
7.HAMMER DRILL FUNCTION
1. Adjust the dial selector to position“
“ to
provide rotation of the chuck (see Fig7)
2. Adjust the lever selector to position“
“ to
provide the hammer action (see Fig8)
3. You are now set up for hammer drilling into
masonry.
8.DRILLING FUNCTION
1. Adjust the dial selector to position “
“ to
provide rotation of the chuck (see Fig9)
2. Adjust the lever selector to position “ “ to stop
the hammer action (see Fig10)
3. You are now set up for drilling function.
WARNING!
Only use 13mm key chuck for drilling
function mode, never use to hammer
action.
9.HAMMER FUNCTION
1. Adjust the dial selector to position “
“ to stop
rotation of the chuck (see Fig11)
2. Adjust the lever selector to position “
“ to
provide the hammer action (see Fig12)
3. You are now set up for chisel work using
hammer action.
WARNING!
If the hammer/drill dial selector will not
drop into place slightly rotate the chuck
to re align the gear box.Before operating select
required mode by aligning symbol on the dial
Fig 8
Fig 9
Fig 6
Fig 7
Lock Button
loosen the chuck

6kg SDS PLUS ROTARY HAMMER SF1022&SF26S6
selector with the arrow on the drill body. There is a
safety lock on the dial selector. When a mode has
been successfully selected the dial selector will
“click” into position.Always make sure it “clicks”
to confirm mode selection.Simply depress the
lock button to move from one mode to another.
10.USING THE DEPTH GAUGE
1. Rotate the handle anti-clockwise, insert depth
gauge into the handle (see Fig13).
2. Adjust the depth gauge to desired depth.
3. Rotate the handle clockwise to tighten the
depth gauge.
11.SAFETY WHEN USING THE ROTARY HAMMER
This is a powerful tool. Caution needs to be
observed when operating. Dress in suitable
overalls. Safety boots are recommended at all
times especially when using the chisel actions.
Proper safety gloves proper safety ear defenders
gloves glasses are also recommended.When
using chisel mode, a dust mask is necessary
because of the cement dust created by the
action.
NOTE: DO NOT USE THE HAMMER WHEN
STANDING ON A LADDER.
12.GEARBOX MAINTENANCE
Always check there is sufficient grease in the
grease box before usage. Check every 5 hrs of
usage. Open the grease box lid at the top of the
drill using the pin spanner provided. Then top
up the grease box (capacity 20gms max) using
the grease provided with your tool. The grease
specification is general purpose lithium based.
(See Fig14)
13.REPLACING CARBON BRUSHES
WARNING!
The carbon brushes and commutator in
your hammer drill have been engineered for may
hours of dependable service.
To maintain peak efficiency of the motor, we
recommend regular inspection of the brushes.
Replace when they wear down to length of about
6mm or less.
To replace the brushes, remove the motor cover,
Fig 12
Fig 13
Fig 10
Fig 11

(see Fig15)
Pull out the worn carbon brushes by pushing
aside the spring clips, insert the new ones and
secure the cover. (see Fig16)
14.CHISEL AND DRILL BITS
Inspect regularly chisel and drill bits for damage
and sharpness. If in doubt obtain new chisels and
bits from a qualified dealer.
MAINTENANCE
1 There are no user serviceable parts in your
power tool except for brushes.
2 Never use water or chemical cleaners to clean
your power tool. Wipe clean with a dry cloth.
3 Always store your power tool in a dry place.
4 Keep the motor ventilation slots clean.
5 If you see some sparks flashing in the ventilation
slots, this is normal and will not damage your
power tool.
HANDY HINTS
Always use sharp good quality drill bits and
chisels. The performance of the drill is dependant
on the quality of the bits used.
- Reduce the pressure on the drill bit when it is
about to break through. This will prevent the drill
from jamming.
- When drilling a large hole, first drill a pilot hole
using a smaller drill bit.
- Always apply pressure to your drill bit in a
straight line, and if possible at right angles to the
workpiece.
- When drilling holes into walls, floors etc., always
make sure that there are no live electrical wires,
or pipe work in the path of the bit.
- Always operate your drill using both the handle
and the front handle.
- Never change the operating mode whilst the
drill is running.
- When using the product in the hammer only
mode, or when chiselling masonry, make sure
that you wear safety glasses and protective
gloves.
- Do not apply excessive pressure to the tool
when chiselling. Expressive force
does not speed up the work.
Fig 14
Fig 15
Tighten
loosen
Fig 16

6kg SDS PLUS ROTARY HAMMER SF1022&SF26S6
ENVIRONMENTAL PROTECTION
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with
your Local Authority or retailer for recycling
advice.

13 AMP
FUSE
BROWN
L (LIVE)
BLUE
N (NEUTRAL)
OUTER
SLEEVE CABLE GRIP
PLUG REPLACEMENT
The fuse in the main plug of your power tool
should always be replaced with one of identical
rating.
Check the voltage given on your power tool
matches the supply voltage.
The power tool is supplied with a fitted plug,
however if you should need to fit a new plug
follows the instruction below.
IMPORTANT
The wire in the mains lead are coloured in
accordance with the following code:
Blue ---Neutral
Brown ---Live
The wire that is coloured blue must be connected
to the terminal that is marked with the letter N.
The wire that is coloured brown must be
connected to the terminal that is marked with the
letter L.
A 13AMP (BS1363 or BS1363/A) plug must be
used and a 13 AMP fuse must be fitted.

6kg SDS PLUS ROTARY HAMMER SF1022&SF26S6
Declaration of Conformity
We, Importer
Screwfix Direct Ltd
Mead Avenue
Houndstone Business Park
Yeovil
BA 22 8RT
Declare that the product
6kg SDS Plus Rotary Hammer Drill
SF26S6&SF1022
Complies with the essential health and safety requirements of the following directives:
89/336/EEC, 93/68/EEC. –EMC Directive.
73/23/EEC, 93/68/EEC. –Low Voltage Directive.
98/37/EC. –Machinery Directive.
Standards and technical specifications referred to:
EN 60745-1:2003/+A1:2003
EN 60745-2-6:2003
EN 55014-1:2000/+A1:2001/+A2:2002
EN 55014-2:1997/+A1:2001
EN 61000-3-2:2000
EN 61000-3-3:1995/+A1:2001
Authorised Signatory
Date: 15/09/05
Signature:
Name: Peter Harries
Screwfix Direct Ltd
Quality Manager
2005