Titan TTB883ROU User manual

Original Instructions_MNL_TTB883ROU_(EN)_V01_211229
WARNING! Read the instructions before using the product!
TTB883ROU
EAN: 5059340253664

EN
2
TTB883ROU
Let's
get started...
These instructions are for your safety. Please read through them thoroughly
before use and retain them for future reference.
Getting started... 02
Safety 03
Symbols 14
Your product 15
Technical and legal information 16
Before you start 19
In more detail... 26
Product functions 27
Operation 34
Care and maintenance 36
Trouble shooting 39
Guarantee 40
Declaration of conformity 41

33
Getting started...
TTB883ROU EN
Safety warnings
General power tool safety warnings
WARNING! Read all safety warnings,
instructions, illustrations and specications
provided with this power tool. Failure to
follow all instructions listed below may result in
electric shock, re and/or serious injury.
Save all warnings and instructions for
future reference. The term “power tool” in
the warnings refers to your mains-operated
(corded) power tool or battery operated
(cordless) power tool.”
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
Safety

44
Getting started...
TTB883ROU
EN
Electrical safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords
increase the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
6. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock.
Safety warnings
Safety

55
Getting started...
TTB883ROU EN
Personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
2. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as a dust mask, non- skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
3. Prevent unintentional starting. Ensure the
switch is in the off- position before connecting
to power source and/or battery pack, picking up
or carrying the tool. Carrying power tools with your
finger on the switch or energising power tools that
have the switch on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing away from
moving parts. Loose clothes, jewellery or longhair
can be caught in moving parts.
Safety

66
Getting started...
TTB883ROU
EN
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
8. Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
Power tool use and care
1. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the rate
for which it was designed.
2. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
3. Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
4. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
Safety warnings
Safety

77
Getting started...
TTB883ROU EN
with the power tool or these instructions to
operate the power tool. Power tools are dangerous
in the hands of untrained users.
5. Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tools operation.
If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control
7. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
8. Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
Service
1. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
Safety

88
Getting started...
TTB883ROU
EN
Additional safety warnings for router
1. Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact its own cord. Cutting a “live”
wire may make exposed metal parts of the power tool
“live” and could give the operator an electric shock.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the workpiece by hand or against your body
leaves it unstable and may lead to less of control.
• Always wear a dust mask and ear protection when
using this power tool.
• Use only bits which are designed for this router.
• Use only sharp bits that are not chipped or cracked.
Blunt bits will cause stalling.
• Secure small pieces of wood firmly before working.
Never hold them in your hand.
• Before starting up, check that the bit is firmly
positioned and secured in the collet.
• The maximum indicated rotation speed of the milling
bit must not be exceeded.
• Routing must always be carried out against the
direction of rotation (bit-rotation) of the bit.
Safety warnings
Safety

99
Getting started...
TTB883ROU EN
• The bit must be running at full speed before lowering
into the work-piece.
• When operating the machine, take great care and
always hold the router handles firmly with both
hands. Always keep secure footing when working.
• Beware of the torque reaction of the machine,
particularly if the bit becomes jammed in the
workpiece.This could cause the tool to turn in the
opposite direction to the direction of bit rotation.
• On completion of work, allow the machine to slide
back to its raised position by releasing the handle.
Keep the machine under control until the bit has
stopped rotating.
• Make yourself familiar with your working area and
be alert for possible hazards which you might not
hear due to machine noise.
• Caution: Allow for run down time of bit after turning
router off. Wait for the machine to come to a
complete stop before removing from the work piece.
• Never slow the router down with your hands.
• Do not touch the bit immediately after operation; it
may be extremely hot and could burn you.
•
Never stop the router by applying lateral pressure to the bit.
• Do not force the router. Your router will do a better
job if you take it slowly.
Safety

1010
Getting started...
TTB883ROU
EN
• Avoid cutting nails and screws. Inspect timber and
remove all nails and screws before cutting.
• In the event of an electrical or mechanical
malfunction, immediately switch off the router and
disconnect the power lead from the mains supply.
• Never use fingers to clear waste material or blockages.
• Turn the router off immediately if the bit gets jammed.
• Ensure the air vents are always unobstructed and
clear. Clean them if necessary with a soft brush.
Blocked air vents may lead to overheating and
damage the product.
• Always keep the power cord behind the tool.
Additional safety warning for construction dust
The updated Control of Substances Hazardous to
Health Regulations 1st October 2012 now also targets
to reduce the risks associated with silica, wood and
gypsum dusts.
Construction workers are one of the at-risk groups
within this because of the dust that they breathe: silica
dust is not just a nuisance; it is a real risk to your lungs!
Silica is a natural mineral present in large amounts
in things like sand, sandstone and granite. It is also
commonly found in many construction materials such
Safety warnings
Safety

1111
Getting started...
TTB883ROU EN
as concrete and mortar. The silica is broken into very
ne dust (also known as Respirable Crystalline Silica
or RCS) during many common tasks such as cutting,
drilling and grinding Breathing in very ne particles of
crystalline silica can lead to the development of: Lung
cancer Silicosis Chronic Obstructive Pulmonary Disorder
Chronic obstructive pulmonary disease (COPD) And
breathing in ne particles of wood dust can lead to the
development of Asthma The risk of lung disease is
linked to people who regularly breathe construction dust
over a period of time, not on the odd occasion.
To protect the lung, the COSHH Regulations sets a
limit on the amount of these dusts that you can breathe
(called a Workplace Exposure Limit or WEL) when
averaged over a normal working day. These limits are
not a large amount of dust: when compared to a penny
it is tiny – like a small pinch of salt:
This limit is the legal maximum; the most you can
breathe after the right controls have been used.
How to reduce the amount of dust?
1. Reduce the amount of cutting by using the best
sizes of building products.
2. Use a less powerful tool e.g. a block cutter instead
of angle grinder.
3. Using a different method of work altogether – e.g.
using a nail gun to direct fasten cable trays instead
of drilling holes first.
Safety

1212
Getting started...
TTB883ROU
EN
Please always work with approved safety equipment,
such as those dust masks that specially designed
to lter out microscopic particles and use the dust
extraction facility at all time.
For more information, please see the HSE website:
http://www.hse. gov.uk/construction or http://www.hse.
gov.uk/pubns/cis69.pdf
WARNING! Some dust created by power
sanding, sawing, grinding, drilling and other
construction activities contains chemicals known
to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• Lead from lead-based paint
• Crystalline silica from bricks and cement and
other masonry products
• Arsenic and chromium from chemically-
treated timber
Your risk from these exposures varies, depending
upon how often you do this type of work. To
reduce your exposure to these chemicals:
• Work in a well-ventilated area.
• Work with approved protective equipment,
such as those dust masks that are specially
designed to lter microscopic particles.
Safety
Safety warnings

1313
Getting started...
TTB883ROU EN
Vibration
The European Physical Agents (Vibration) Directive
has been brought in to help reduce hand arm vibration
syndrome injuries to power tool users. The directive
requires power tool manufacturers and suppliers to
provide indicative vibration test results to enable users
to make informed decisions as to the period of time a
power tool can be used safely on a daily basis and the
choice of tool.
See technical specications in the instruction manual
for the vibration levels of your tool.
The declared vibration emission value should be used
as a minimum level and should be use with the current
guidance on vibration.
Calculating the actual period of use can be difcult and
the HSE website has further information.
While working with this power tool, hand/arm vibrations
occur. Adopt the correct working practices in order to reduce
the exposure to vibration. This tool may cause hand-arm
vibration syndrome if its use is not adequately managed.
Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades. Maintain
this tool in accordance with these instructions and keep
well lubricated (where appropriate).
Avoid using tools in temperatures of 10ºC or less. Plan
your work schedule to spread any high vibration tool
use across a number of days.
Safety

1414
Getting started...
TTB883ROU
EN
NOTE: The use of other tools will reduce the users’ total
working period on this tool.
Health surveillance
All employees should be part of an employer’s health
surveillance scheme to help identify any vibration
related diseases at an early stage, prevent disease
progression and help employees stay in work.
Symbols
On the product, the rating label and within these instructions
you will nd among others the following symbols and
abbreviations. Familiarise yourself with them to reduce
hazards like personal injuries and damage to property.
Read the instruction manual
Wear eye protection
Wear hearing protection.
Wear a dust mask.
Wear protective gloves.
Wear protective, slip resistant footwear.
Switch the product off and disconnect it from
the power supply before assembly, cleaning,
adjustments, maintenance, storage and
transportation.
Symbols

1515
Getting started...
TTB883ROU EN
Class II equipment
yyWxx Manufacturing date code: Year of manufacturing
(20yy) and week of manufacturing (Wxx)
The product complies with the applicable
European directives and an evaluation
method of conformity for these directives
was done.
UK Comformity Assessed
Symbols

1616
Getting started...
TTB883ROU
EN
Your product
2
13
10
8a
8
7
9
4
6a
6b
6c
12
3
5
11
14
1
6
20
Your product

1717
Getting started...
TTB883ROU EN
1. On/off switch
2. Lock-off button
3. Speed adjuster
4. Plunge lock lever
5. Spindle lock button
6. Socket
6a.Collet nut
6b.Collet (6.35mm and 8mm
for UK; 6mm and 8mm for
other countries)
6c.Spindle
7. Depth step buffer
8. Depth stop
8a.Depth stop arrow
9. Fine adjustment
9a. Fine adjustment knob
9b.Scale wheel
10.Locking screw
11.Screw for edge guide
12.Base plate
13.Handle
14.Transparent cover
15.Edge guide
16. Wrench
17.Centering pin
18.Fixing screw (x4)
19.Fixing nut (x2)
20.Dust extraction adaptor
(with xing nut)
21.Guide bush
15 16
17 18 6b19 20 21 9a
9b

1818
Getting started...
TTB883ROU
EN
Technical specications
Router
Rated voltage, frequency: 220 -240 V~, 50 Hz
Rated power input: 1200 W
Rated no load speed n0:11000 - 30000 /min
Collet size: 6.35 / 8 mm
Max cutting depth: 55mm
Weight: 3.2 kg
NOISE DATA
A weighted sound pressure: LpA= 89.5 dB(A)
A weighted sound power: LwA= 100.5 dB(A)
Uncertainty: K = 3 dB(A)
The noise for the operator may exceed 80 dB(A) and ear
protection measures are necessary.
VIBRATION DATA
Hand arm vibration: ah = 6.3 m/s²
Uncertainty: K= 1.5 m/s2
The declared vibration total values and the declared noise
emission values have been measured in accordance with a
standard test method (EN62841-1/EN62841-2-17) and may be
used for comparing one tool with another; they may also be used
in a preliminary assessment of exposure.
WARNING! The vibration and noise emissions
during actual use of the power tool can differ
from the declared values depending on the
ways in which the tool is used especially what
kind of workpiece is processed; and need to
identify safety measures to protect the operator
that are based on an estimation of exposure
in the actual conditions of use (taking account
of all parts of the operating cycle such as the
times when the tool is switched off and when it
is running idle in addition to the trigger time).
Technical and legal
information

1919
Getting started...
TTB883ROU EN
RATING LABEL EXPLANATION
TTB883ROU = MODEL NUMBER
TT= TITAN
B=240V AC
883= Version Number
ROU = Router
Before you start

2020
Getting started...
TTB883ROU
EN
Unpack
Unpack all parts and lay them on a flat, stable surface.
Remove all packing materials and shipping devices if
applicable.
Make sure the delivery contents are complete and free
of any damage. If you find that parts are missing or show
damage do not use the product but contact your dealer.
Using an incomplete or damaged product represents a
hazard to people and property.
Ensure that you have all the accessories and tools needed
for assembly and operation. This also includes suitable
personal protective equipment.
WARNING! The product and the packaging
are not children's toys! Children must not play
with plastic bag, sheets and small parts! There
is a danger of choking and suffocation!
You will need
(items not supplied)
Suitable personal protective equipment
Router bits
(items supplied)
Guide bush
Dust extraction adaptor
Parallel guide
Collets
Wrench
Centering pin
Before you start