Titan TTB924DBT User manual

Original Instructions_MNL_TTB924DBT_GB_V1_220421
TTB924DBT
350W Drill Press
CAUTION: Read the instructions before using the product.
EN
V10422 / BX220IM
EAN: 5059340397627
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 1MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 1 2022/4/21 2:54 PM2022/4/21 2:54 PM

EN
02
38
39
40
36
34
32
27
In more detail...
Product functions
Operation
Care and maintenance
Troubleshooting
Recycling and disposal
Guarantee
Declaration of conformity
26
02
03
16
20
Getting started...
Safety information
Your product
Before you start
These instructions are for your safety. Please read through them
thoroughly before use and retain them for future reference.
Let’s
get started...
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 2MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 2 2022/4/21 2:54 PM2022/4/21 2:54 PM

TTB924DBT by TITAN
Getting started...
03
EN
Safety information
Safety warnings
General power tool safety warnings
WARNING! Read all safety warnings, instructions,
illustrations and specications provided with this
power tool. Failure to follow all instructions listed
below may result in electric shock, re and/or
serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodied plugs and matching outlets will reduce risk
of electric shock.
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 3MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 3 2022/4/21 2:54 PM2022/4/21 2:54 PM

04
TTB924DBT by TITAN
Getting started...
EN
Safety information
Safety warnings
b) Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Donotexposepowertoolstorainorwetconditions.
Water entering a power tool will increase the risk of
electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 4MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 4 2022/4/21 2:54 PM2022/4/21 2:54 PM

TTB924DBT by TITAN
Getting started...
05
EN
Safety information
c) Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on the
switch or energising power tools that have the switch
on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of
tools allow you to become complacent and ignore
tool safety principles. A careless action can cause
severe injury within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 5MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 5 2022/4/21 2:54 PM2022/4/21 2:54 PM

06
TTB924DBT by TITAN
Getting started...
EN
Safety information
Safety warnings
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
e) Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect
the power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents are
caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and
control of the tool in unexpected situations.
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 6MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 6 2022/4/21 2:54 PM2022/4/21 2:54 PM

TTB924DBT by TITAN
Getting started...
07
EN
Safety information
5) Service
a) Have your power tools serviced by a qualied
repair person using only identical replacement
parts. This will ensure that safety of the power tool is
maintained.
Safety instructions for drill press
a) The drill must be secured. A drill that is not properly
secured may move or tip over and may result in
personal injury.
b) The workpiece must be clamped or secured to the
workpiece support. Do not drill pieces that are too
small to be clamped securely. Holding the workpiece
by hand during operation may result in personal injury.
c) Do not wear gloves. Gloves may be entangled by the
rotating parts or chips leading to personal injury.
d) Keep your hands out of the drilling area while the
tool is running. Contact with rotating parts or chips
may result in personal injury.
e) Make sure the accessory is rotating before feeding
into the workpiece. Otherwise the accessory may
become jammed in the workpiece causing unexpected
movement of the workpiece and personal injury.
f) When the accessory is jammed, stop applying
downward pressure and switch off the tool.
Investigate and take corrective actions to eliminate
the cause of the jam. Jamming can cause unexpected
movement of the workpiece and personal injury.
g) Avoid generating long chips by regularly
interrupting downward pressure. Sharp metal chips
may cause entanglement and personal injuries.
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 7MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 7 2022/4/21 2:54 PM2022/4/21 2:54 PM

08
TTB924DBT by TITAN
Safety information
Getting started...
EN
Safety warnings
h) Never remove chips from the drilling area while
the tool is running. To remove chips, move the
accessory away from the workpiece, switch off the
tool and wait for the accessory to stop moving.
Use tools such as a brush or hook to remove
chips. Contact with rotating parts or chips may result
in personal injury.
i) Accessories with speed ratings must be rated at
least equal to the maximum speed marked on the
power tool. Accessories running faster than their
rated speed can break and y apart.
Additional safety warnings for drill press
a) Keep bits clean and sharp. Sharp bits minimize
stalling. Dirty and dull bits may cause misalignment of
the material and possible operator injury.
b) Never use excessive force on the handle.
c) Always ensure the product is securely mounted to a
solid workbench.
d) Never remove the guard.
e) Adjust the table or depth stop to avoid drilling into the
table. Shut off the power, remove the drill bit, and clean
the table before leaving the product.
f) Never perform any operation by moving the head
or table with respect to one another. Do not turn the
motor switch on or start any operation before checking
that the head and table support lock handle is clamped
tight to column and head and table support collars are
correctly positioned.
g) Before engaging the power switch, make sure the belt
guard is down and the chuck is installed properly.
h) Do not perform layout, assembly, or set-up work on
the table while the cutting tool is rotating, switched on,
or connected to a power source.
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 8MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 8 2022/4/21 2:54 PM2022/4/21 2:54 PM

TTB924DBT by TITAN
Getting started...
Safety information
EN
9
i) If the power supply cord is damaged, it must be
replaced only by the manufacturer or by an authorised
service centre to avoid risk.
j) Care should be taken when drilling brass and copper
as drill may jam and break if too much pressure is
applied.
The following information applies to professional
users only but is good practice for all users:
ADDITIONAL SAFETY WARNING FOR
CONSTRUCTION DUST
The updated Control of Substances Hazardous to Health
Regulations 1st October 2012 now also targets to reduce
the risks associated with silica, wood and gypsum dusts.
Construction workers are one of the at- risk groups within
this because of the dust that they breathe: silica dust is
not just a nuisance; it is a real risk to your lungs!
Silica is a natural mineral present in large amounts
in things like sand, sandstone and granite. It is also
commonly found in many construction materials such as
concrete and mortar. The silica is broken into very ne
dust (also known as Respirable Crystalline Silica or RCS)
during many common tasks such as cutting, drilling and
grinding. Breathing in very ne particles of crystalline
silica can lead to the development of:
• Lung cancer
• Silicosis
• Chronic Obstructive Pulmonary Disorder / Chronic
obstructive pulmonary disease (COPD)
And breathing in ne particles of wood dust can lead to
the development of Asthma. The risk of lung disease is
linked to people who regularly breathe construction dust
over a period of time, not on the odd occasion.
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 9MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 9 2022/4/21 2:54 PM2022/4/21 2:54 PM

TTB924DBT by TITAN
Getting started...
EN
10
Safety information
Safety warnings
To protect the lung, the COSHH Regulations sets a limit
on the amount of these dusts that you can breathe (called
a Workplace Exposure Limit or WEL) when averaged
over a normal working day. These limits are not a large
amount of dust: when compared to a penny it is tiny – like
a small pinch of salt:
This limit is the legal maximum; the most you can breathe
after the right controls have been used.
HOW TO REDUCE THE AMOUNT OF DUST?
a) Reduce the amount of cutting by using the best sizes
of building products.
b) Use a less powerful tool e.g. a block cutter instead of
angle grinder.
c) Using a different method of work altogether – e.g.
using a nail gun to direct fasten cable trays instead of
drilling holes rst.
Please always work with approved safety equipment,
such as those dust masks that specially designed to lter
out microscopic particles and use the dust extraction
facility at all time.
For more information please see the HSE website:
http://www.hse.gov.uk/construction or http://www.hse.gov.
uk/pubns/cis69.pdf
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 10MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 10 2022/4/21 2:54 PM2022/4/21 2:54 PM

TTB924DBT by TITAN
Getting started...
EN
11
Safety information
WARNING! Some dust particles created by power
sanding, sawing, grinding, drilling and other
construction jobs contain chemicals known to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and
other masonry products.
• Arsenic and chromium from chemically treated
timber.
Your risk from these exposures varies, depending
upon how often you do this type of work. To reduce
your exposure to these chemicals:
• Work in a well-ventilated area.
• Work with approved safety equipment, such as
those dust masks that are specially designed to
lter microscopic particles.
VIBRATION
The European Physical Agents (Vibration) Directive
has been brought in to help reduce hand arm vibration
syndrome injuries to power tool users. The directive
requires power tool manufacturers and suppliers to
provide indicative vibration test results to enable users to
make informed decisions as to the period of time a power
tool can be used safely on a daily basis and the choice of
tool.
SEE TECHNICAL SPECIFICATIONS IN THE
INSTRUCTION MANUAL FOR THE VIBRATION
LEVELS OF YOUR TOOL.
The declared vibration emission value should be used
as a minimum level and should be used with the current
guidance on vibration.
Calculating the actual period of use can be difcult and
the HSE website has further information.
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 11MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 11 2022/4/21 2:54 PM2022/4/21 2:54 PM

TTB924DBT by TITAN
Getting started...
EN
12
Safety warnings
The declared vibration emission value has been measured
in accordance with a standardised test and may be used
to compare one tool with another.
The declared vibration emission value may also be used
in a preliminary assessment of exposure.
WARNING! The vibration emission value during
actual use of the power tool can differ from the
declared value depending on the ways in which
the tool is used:
• How the materials are grinded, cut or drilled.
• If the tool is in good condition and well maintained.
• Use correct accessory for the tool and ensure it
is sharp and in good condition.
• The tightness of the gripping handles.
• The tool is being used as intended by its design
and these instructions.
While working with this power tool, hand/arm
vibrations occur. Adopt the correct working practices
in order to reduce the exposure to vibration. This
tool may cause hand-arm vibration syndrome if its
use is not adequately managed.
Safety information
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 12MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 12 2022/4/21 2:54 PM2022/4/21 2:54 PM

TTB924DBT by TITAN
Getting started...
EN
13
WARNING! Identify safety measures to protect
the operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
Note:
• The use of other tools will reduce the users’ total
working period on this tool.
• Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades.
• Maintain this tool in accordance with these
instructions and keep well lubricated (where
appropriate).
• Avoid using tools in temperatures of 10ºC or
less. Plan your work schedule to spread any
high vibration tool use across a number of days.
Health surveillance
All employees should be part of an employer’s health
surveillance scheme to help identity any vibration related
diseases at an early stage, prevent disease progression
and help employees stay in work.
Vibration and noise reduction
To reduce the impact of noise and vibration emission,
limit the time of operation, use low-vibration and
low-noise operating modes as well as wear personal
protective equipment.
Take the following points into account to minimise the
vibration and noise exposure risks:
a) Only use the product as intended by its design and
these instructions.
b) Ensure that the product is in good condition and well
maintained.
Safety information
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 13MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 13 2022/4/21 2:54 PM2022/4/21 2:54 PM

TTB924DBT by TITAN
Getting started...
EN
14
Safety warnings
c) Use correct attachments for the product and ensure
they are in good condition.
d) Keep tight grip on the handles/grip surface.
e) Maintain this product in accordance with these
instructions and keep it well lubricated (where
appropriate).
f) Plan your work schedule to spread any high vibration
tool use across a longer period of time.
g) Prolonged use of the product exposes the user
to vibrations that can cause a range of conditions
collectively known as hand-arm vibration syndrome
(HAVS) e.g. ngers going white; as well as specic
diseases such as carpal tunnel syndrome. To reduce
this risk when using the product, always wear protective
gloves when appropriate for use and keep your hands
warm.
Emergency
Familiarise yourself with the use of this product by
means of this instruction manual. Memorise the
safety directions and follow them to the letter. This
will help to prevent risks and hazards.
a) Always be alert when using this product, so that
you can recognise and handle risks early. Fast
intervention can prevent serious injury and damage to
property.
b) Switch off and disconnect from the power supply
if there are malfunctions. Have the product checked
by a qualied professional and repaired, if necessary,
before you operate it again.
Safety information
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 14MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 14 2022/4/21 2:54 PM2022/4/21 2:54 PM

TTB924DBT by TITAN
Getting started...
EN
15
Residual risks
Even if you are operating this product in accordance
with all the safety requirements, potential risks of
injury and damage remain. The following dangers
can arise in connection with the structure and design
of this product:
a) Health defects resulting from vibration emission if the
product is being used over long periods of time or not
adequately managed and properly maintained.
b) Injuries and damage to property due to broken cutting
attachments or the sudden impact of hidden objects
during use.
c) Danger of injury and property damage caused by ying
objects or poor power tool accessories.
WARNING! This product produces an
electromagnetic eld during operation! This eld
may under some circumstances interfere with
active or passive medical implants! To reduce
the risk of serious or fatal injury, we recommend
persons with medical implants to consult their
doctor and the medical implant manufacturer
before operating this product!
Safety information
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 15MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 15 2022/4/21 2:54 PM2022/4/21 2:54 PM

TTB924DBT by TITAN
Getting started...
EN
16
Your product
Your product
12
3
4
5
6
7
8
9
9a
10
11a
11b
11
22
21
12
13
14
15
16
17
19
18
6c
20
20b
20a
1. Pulley cover
a.Locking knob*
2. Belt pulley (x2)
3. Belt
4. Belt tension lock
knob
5. Motor unit
a.Air vents*
6. Machine head
a.Locking bolt* (x2)
b.Spindle neck*
c.Ring hole
d.Spindle*
7. Feed handle (x3)
8. Column
9. Clamp
a.Clamp lever
10. Support
11. Base
a.Mounting bolt (x3)
b.Mounting hole (x2)
12. Power cord with plug
13. Drill table
a.Pointer line*
b.Angle scale (±45)
c.Hex bolt*
14. Chuck guard
a.Clamp*
b.Crosshead bolt*
c.Nut*
d.Cover (x2)
e.Wing nut* (x2)
f. Hex bolt* (x2)
15. Drill chuck
a.Jaws*
16. Spindle feed head
17. Key holder
18. Green On button I
19. Red Off button O
20. Depth scale
a.Scale meter
(0-50mm)
b.Red pointer
c.Nut*
21. Chuck key
22. 4mm hex key
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 16MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 16 2022/4/21 2:54 PM2022/4/21 2:54 PM

TTB924DBT by TITAN
Getting started...
EN
17
Your product
NOTE: Parts marked with * are not shown in this overview. Please
refer to the respective part in the instruction manual.
Technical specications
Drill Press
> Rated voltage, frequency : 230-240 V~, 50 Hz
> Rated input : 350 W S1, 500 W S6 40%
> Rated no load speed n0: 1450 min-1
> Spindle speed : 600-2650 min-1
> Drill capacity : Ø 1.3 - 13 mm
> Drill chuck : B16
> Max. drill depth : 50 mm
> Drill table tilting range : 0° - ±45°
> Drill table dimensions : 160 x 160 mm
> Protection type : IPX0
> Protection class : I
> Weight : approx. 13.6 kg
> Dimensions : approx. 420 x 210 x 600 mm
Sound values
> Sound pressure level LpA :70.8 dB (A)
> Uncertainty KpA 3 dB (A)
> Sound power level LWA :83.8 dB (A)
> Uncertainty KWA :3 dB (A)
Hand arm vibration values
> Hand arm vibration ah,W :< 2.5 m/s²
> Uncertainty K : 1.5 m/s²
The sound values have been determined according to noise test code given in
EN 62841-1 and EN 62841-3-13, using the basic standards EN ISO 11203 and
ISO 3744.
The sound intensity level for the operator may exceed 80 dB(A) and ear protection
measures are necessary.
The declared vibration value and sound values have been measured in
accordance with a standard test method (according to EN 62841-1) and may be
used for comparing one product with another.
The declared vibration total value(s) and the declared noise emission value(s)
may also be used in a preliminary assessment of exposure.
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 17MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 17 2022/4/21 2:54 PM2022/4/21 2:54 PM

TTB924DBT by TITAN
Your product
Getting started...
EN
18
Technical specications
WARNING! The vibration and noise emissions during actual use of the
power tool can differ from the declared values depending on the ways
in which the tool is used especially what kind of workpiece is processed;
and need to identify safety measures to protect the operator that are
based on an estimation of exposure in the actual conditions of use
(taking account of all parts of the operating cycle such as the times
when the tool is switched off and when it is running idle in addition to
the trigger time).
Rating label explanation
TTB924DBT = Model number
TT = TITAN
B = Voltage (230-240 V~)
924 = Sequential Code
DBT = Drill Bench Top
Symbols
On the product, the rating label and within these instructions you will nd among
others the following symbols and abbreviations. Familiarise yourself with them to
reduce hazards like personal injuries and damage to property.
V~ Volt (alternating voltage) Hz Hertz
W Watt mm Millimetre
n0No-load speed g Gram
/min or
min-1
Per minute kg Kilogram
dB(A) Decibel (A-rated) m/s² Metres per seconds squared
S1 Operation mode S1 – continuous operation
This means that you may operate the motor continuously at its power
level (350W).
S6 40% Operating mode S6 - intermittent periodic duty
This means that you may operate the motor continuously at its nominal
power level (500W) for no longer than the time (4 min) stipulated on the
specications label. If you fail to observe this time limit the motor will
overheat. During the no-load running period the motor will cool again to
its starting temperature.
Lock / to tighten or secure. Unlock / to loosen.
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 18MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 18 2022/4/21 2:54 PM2022/4/21 2:54 PM

TTB924DBT by TITAN
Getting started...
Your product
EN
19
Note / Remark. Caution / Warning.
yyWxx Manufacturing date code; year of manufacturing (20yy) and week of
manufacturing (Wxx)
Read the instruction manual. Wear hearing protection.
Wear eye protection. Wear a dust mask.
Wear protective gloves when
handling drill bits and rough
workpieces.
Wear protective, slip-resistant
footwear.
Switch the product off and disconnect it from the power supply
before assembly, cleaning, adjustments, maintenance, storage and
transportation.
Never wear a necktie during operation!
This product shall be operated by one person only!
Always secure the workpiece!
Do not expose the product to rain or wet conditions (moisture).
Wait until all product components have completely stopped before
touching them.
This product is classied as protection class I and must be connected
to a protective ground during operation.
Open ames in the work area, around the product and in the vicinity of
ammable materials are prohibited!
Do not smoke in the work area, around the product and in the vicinity of
ammable materials!
WEEE symbol. Waste electrical products should not be disposed of
with household waste. Please recycle where facilities exist. Check with
your Local Authority or local store for recycling advice.
The product complies with the applicable European directives and an
evaluation method of conformity for these directives was done.
UK Conformity Assessed.
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 19MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 19 2022/4/21 2:54 PM2022/4/21 2:54 PM

TTB924DBT by TITAN
Getting started...
EN
20
Before you start
Unpacking
WARNING! The product is heavy, ask another person for assistance
if required!
1. Unpack all parts and lay them on a at, stable surface.
2. Remove all packing materials and shipping devices if applicable.
3. Make sure the delivery contents are complete and free of any damage. If
you nd that parts are missing or show damage do not use the product but
contact your dealer. Using an incomplete or damaged product represents a
hazard to people and property.
4. Ensure that you have all the accessories and tools needed for assembly and
operation. This also includes suitable personal protective equipment.
WARNING! The product and the packaging are not children’s toys!
Children must not play with plastic bags, sheets and small parts! There
is a danger of choking and suffocation!
The drill press comes partially assembled for packaging purposes. The following
items are included with your drill press (Fig. A).
Fig. A
MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 20MNL_TTB924DBT_350W Drill Press_GB_EU_V1_220421.indd 20 2022/4/21 2:54 PM2022/4/21 2:54 PM