TOORX BRX95 User manual

Ed: 02/17
INSTRUCTION
Rev: 0000

Pre-assembly Notes
Open the bo es:
Make sure to inventory all the parts that are included in the box. Check the hardware
chart
of a full count of the number of parts included for proper assembly . If any of the parts
are
missing, contact with the dealer.
NO. NAME SPECIFICATION QTY
9 Allen C.K.S. half thread screw M8×50× 0 4
30 Spring washer Φ8 6
31 Flat washer Φ8.5×Φ 0×t1.5 6
3 Allen C.K.S. full thread screw M8× 0 1
33 Curved washer Φ8.5×R 5×t .0 1
2

34 Allen C.K.S. half thread screw M8×63× 0
35 Hex self-locking nut M8 1
36 Philips C.K.S. self-tapping screw ST4×16
37 Philips pan head full thread screw M4×6 4
38 Philips pan head full thread screw M5×10 4
39 Philips pan head full thread screw M4×10 4
GATHER YOUR TOOLS
Before starting the assembly of your unit ，gather the necessary tools.Having all of the
equipment at hand will save time and make the assembly quick and hassle-free.
CLEAR YOUR WORK AREA
Make sure that you have cleared away a large enough space to properly assemble the
unit. Make sure the space is free from anything that may cause injury during assembly.
After the unit is fully assembled, make sure there is a comfortable amount of free area
around the unit for unobstructed operation.
NOTE: Each step number in the assembly instructions tells you what you will be doing.
Read and understand all instructions thoroughly before assembling the treadmill.
Name Specification QTY
L-shape wrench 5×80×80S 1
L-shape wrench 6×40×1 0 1
Cross spanner 15#&17# 1
Cross open spanner 1
3

Product instruction
Technical information
4
Bottle holder
Handle bar
Controller
Motor belt
Pedal
Wheel
Front stabilizer
Rear stabilizer
Saddle
Console

DIMENSION Unfold：1100x530x1400mm
FLYWHEEL One -way, Φ 80/6kg
RESISTANCE
FRAGMENT 3 levels
UP&DOWN 15 .4 mm distance
FRONT&BACK 70mm distance
*WE
RESERVE THE RIGHT TO AMEND THE PRODUCT WITHOUT PRIOR NOTICE.
Step 1: Attach the front stabilizer ( ) to the main frame (1) with flat washer(31), spring
washer(30) and Allen C.K.S. half thread screw( 9).
Step 2: Attach the rear stabilizer (3) to the main frame (1) with flat washer(31), spring
washer(30) and Allen C.K.S. half thread screw( 9).
5
ASSEMBLY INSTRUCTIONS

Step 3:
1.Attach the Upright post decoration strip(46) to the upper upright post(4),take upright
post cover(19) off from the main frame(1) and cover it on the upper upright post.(4)
.Connect Motor communication wire (1 ) and Console communication wire (13).
3. Attach upper upright post(4) to the main frame(1) with Curved washer( 33), spring
washer(30), Allen C.K.S. half thread screw(34) and flat washer(31), spring washer(30),
Allen C.K.S. full thread screw(3 ) and flat washer(31),Allen C.K.S. half thread screw(34),
Hex self-locking nut(35).
4.Attach upright post cover(19) and Upright post decoration strip(46) to the main
frame(1).
5.Attach bottle holder( 0) to upper upright post(4) with Philips pan head full thread
screw(36).
Tip: Put the communication wires and resistance adjust knob wire into the upright
post,and make sure all screws are in the hexagonal hole before tighten all the bolts.
6

31 30 32
35
31
34
19
1
33
30
34
3
13 12
4
46
20
36
Step 4:
Attach the Pedal(L)(5) and Pedal(R)(6) to the Main frame(1),then tighten the bolts.
7

Step 5:
1.Loose the Rotary hand bolt( 1),attach the Saddle post (7) to the
Main frame(1),then tighten the Rotary hand bolt( 1).
5
7
1
21
Step 6:
8

1,Attach the saddle adjustment set (60) to the saddle post (7) and place it onto correct
position .Lock them with bushing ( 3) and rotary knob ( ) .
, Put the saddle (8) onto the saddle adjustment set (60) and lock it tightly .
3, Attach the saddle cover(L)( 4) and saddle cover(L)( 5) to the saddle post(7),and use
Philips pan head full thread screw(37) to tighten them.
68
25
37
37
24
7
21 23
22
60
Step 7:
1. Handle pulse connection wire （16 ）through the Upright post(4),and attach the
9

Handlebars(9) to Upright post(4),tighten with rotary knob( 6).
. Attach Console fixed piece(10) to the Upright post(4),tighten with Philips C.K.S. full
head screw(38).
Tip: Make sure all screws are in the hexagonal hole before tighten all the bolts.
7
4
38
38
10
9
26
16
Step 8:
10

1. C o n n e c t t h e Console communication wire( 1 3 ) a n d Console connection
wire(18),connect the Handle pulse connection wire(16) and Console outset(17).
. Attach the Console(11) to the Console fixed piece(10),tighten with Philips C.K.S. full
head screw(40).
3. Attach the Handlebar cover(L)( 7) a nd Handlebar cover(R)( 8) through the
Handlebars(9) to the Upright post(4),tighten with Philips C.K.S. full head screw(39).
Tip: Make sure all screws are in the hexagonal hole before tighten all the bolts.
811
10
9
40
27
39
28 39
18
17
16
13
Workout tips:
1,User need to put the feet completely inside the pedal, and to adjust the resistance of
magnet control according to user.
,Since the machine with double flywheels and it will have huge moment of inertia, when
the user stop before high speed, the user should minimize the resistance and lower the
speed, to avoid hurt the user’s leg by the moment of inertia of left and right pedal
3,The machine should be put on flat floor and have enough space for workout
Half-drawing for assembly
11

29
30
31
29
30
31
29
30
31
31 30 32
31
34
19
33
30
34
5
6
7
25
37
37
24
23
22
26
38
38
9
40
10
11
39
27
28
39
17
13
2
3
21
16
1
18
13 12
4
46
20
36
8
60
35
12

Part list
NO. NAME SPECIFICATION QTY
1Main frame 1
Front stabilizer 1
3Rear stabilizer 1
4Upright post 1
5Pedal(L) 1
6Pedal(R) 1
7Saddle post 1
8Saddle 1
9Handlebars 1
10 Console fixed piece 1
11 Console 1
1 Magnetic sensor wire 1
13 Console communication wire 1
14 Resistance adjust knob wire 1
15 Resistance adjust knob 1
16 Handle pulse connection wire
17 Console outset
18 Console connection wire 1
19 Upright post cover 1
0 Bottle holder 1
1 Rotary hand bolt Φ56×M16×P1.5 1
13

Handlebar rotary knob Φ60×31×M10× 0 1
3 Bushing Φ10.5×Φ14×10 1
4 Saddle cover(L) 1
5 Saddle cover(R) 1
6 Rotary knob Φ54×8 ×M8×30 1
7 Handlebar cover(L) 1
8 Handlebar cover(R) 1
9 Allen C.K.S. half thread screw M8×50× 0 4
30 Spring washer Φ8 6
31 Flat washer Φ8.5×Φ 0×t1.5 6
3 Allen C.K.S. full thread screw M8× 0 1
33 Curved washer Φ8.5×R 5×t .0 1
34 Allen C.K.S. half thread screw M8×63× 0
35 Hex self-locking nut M8 1
36 Philips C.K.S. self-tapping screw ST4×16
37 Philips pan head full thread screw M4×6 4
38 Philips pan head full thread screw M5×10 4
39 Philips pan head full thread screw M4×10 4
40 Philips pan head full thread screw M5×10 4
46 Upright post decoration strip 1
60 Saddle adjustment set 1
14

Drawig for assembly
15

16
59
15
14
13
91
65
51
85
32
35
64
51
66
63
35
73
75
76
62
62
63
63
67
69
68
70
72
52
74
84
31
57
58 35
32
31
47
48
48
2
50
49
47
51 31
30
29 30
29
31
86
29
30
31
29
30
31
3
31 30 32
4
33
30
34
38
38
40
10
11
39
27
28
39
17
46
19
81
44 81
81
88
89
43
43
44
61
67
36
36
36
36
41
67
83
71
83
71
42
6
5
7
25
37
23
22
24
80
79
87 87
37
77
60
8
35
51
54
53
56
78
1
9
21
81
18
12
82
55
36
45
36
92
20
36
26
90
94
93
31
34
35
16

Part list
NO. NAME SPECIFICATION QTY
1Main frame 1
Front stabilizer 1
3Rear stabilizer 1
4Upright post 1
5Pedal(L) 1
6Pedal(R) 1
7Saddle post 1
8Saddle 1
9Handlebars 1
10 Console fixed piece 1
11 Console 1
1 Motor communication wire 1
13 Console communication wire 1
14 Power communication wire 1
15 Magnetic sensor 1
16 Handle pulse connection wire
17 Console outset
18 Console connection wire 1
19 Upright post cover 1
0 Bottle holder 1
1 Rotary hand bolt Φ56×M16×P1.5 1
17

Handlebar rotary knob Φ60×31×M10× 0 1
3 Bushing Φ10.5×Φ14×10 1
4 Saddle cover(L) 1
5 Saddle cover(R) 1
6 rotary knob Φ54×8 ×M8×30 1
7 Handlebar cover(L) 1
8 Handlebar cover(R) 1
9 Allen C.K.S. half thread screw M8×50× 0 4
30 Spring washer Φ8 6
31 Flat washer Φ8.5×Φ 0×t1.5 7
3 Allen C.K.S. full thread screw M8× 0 6
33 Curved washer Φ8.5×R 5×t .0 1
34 Allen C.K.S. half thread screw M8×63× 0
35 Hex self-locking nut M8 8
36 Philips C.K.S. self-tapping screw ST4×16 1
37 Philips pan head full thread screw M4×6 4
38 Philips pan head full thread screw M5×10 4
39 Philips pan head full thread screw M4×10 4
40 Philips pan head full thread screw M5×10 4
41 Crank(L) 1
4 Crank® 1
43 Crank cover
44 Philips C.K.S. self-tapping screw ST4×1 4
18

45 Magnetic motor 1
46 Upright post decoration strip 1
47 End cap 4
48 Feet pad Φ47×10.5×M10× 0 4
49 Hex nut Φ8×33×M6×15
50 Wheels Φ55× 5.8
51 Allen C.K.S. full thread screw M6×15 5
5 Deep groove ball bearing 6 03- RS 1
53 Hex nut M5
54 Allen C.K.S. full thread screw M5×80 1
55 Philips C.K.S. self-tapping screw ST4×1 1
56 Saddle post bushing 1
57 Crank axle Φ17×154.3 1
58 Belt pulley Φ 63×19 1
59 Power adapter 1
60 Saddle adjustment set 1
61 Circlip shaft Φ17
6 Circlip shaft Φ1
63 Circlip shaft Φ10 3
64 Tension pulley Φ38× 1
65 Tension spring 1
66 Brake tension spring 1
67 Deep groove ball bearing 6003- RS 3
19

68 Magnetic control fixed axle Φ1 ×50 1
69 Deep groove ball bearing 6300- RS 1
70 Flat washer Φ34×Φ 5×t1.0 1
71 Crank cover
7 Unidirectional needle bearing Φ35×Φ17×16 1
73 Small belt pulley set Φ30×64 1
74 Deep groove ball bearing 6000- RS 1
75 Flywheel axle Φ10×109.5 1
76 Flywheel Φ 80/6kg 1
77 Square end cap 0×40×t1.5 1
78 Handle pulse set
79 Philips C.K.S. self-tapping screw ST4× 0
80 Round end cap Φ 5×t1.5
81 Philips C.K.S. self-tapping screw ST4× 5 7
8 Fixed magnet set 1
83 Allen C.K.S. full thread screw 5/16-18UNC-1"
84 Tension pulley 1
85 Magnetic control fixed axle 1
86 Motor belt 440PJ6 1
87 Foam grip Φ ×t3.0×680
88 Cover（L） 1
89 Cover（R） 1
90 Saddle locking piece 1
20