TOORX BRX60 User manual

Ed : 02/17 Rev : 00
INSTRUCTION

3
PARTS LIST
NO. DESCRIPTION Q’TY NO. DESCRIPTION Q’TY
1 MAIN FRAME 1 34 PEDAL L/R 1/1
2 REAR STABILIZER 1 35 CURVE WASHER Φ8*Φ20 4
3 END CAP FOR REAR STABILIZER 2 36 ROUND END CAPS Φ25.4 2
4 CARRIAGE BOLT M10*65 4 37 END CAP FOR WIRE 1
5 FRONT STABILIZER 1 38 POWDER SPACER 1
6
END CAP FOR FRONT STABILIZER
2 39 SELF-TAPPING SCREW ST5*15 4
7 CURVE WASHER Φ10*Φ22 4 40 SELF-TAPPING SCREW ST5*15 8
8 DOMED NUT M8 4 41 CRANK L/R 1/1
9 QUICK RELEASE KNOB 1 42 BB ASSEMBLY 1
10 ALLEN SCREW M8*16 4 43 SEAT POST PLASTIC SLEEVE 1
11 SEAT 1 44 SENSOR BRACKET 1
12 FRONT POST 1 45 SPRING 1
13 TENSION KNOB +CABLE UPPER 1 46 FRENCH NUT 4
14 SENSOR WIRE MIDDLE 1 47 PULLY 1
15 SCREW M5*10 2 48 END CAP FOR CRANK 2
16
SPACER
1 49 SPACER FOR MAGNET 2
17 SQUARE WASHER 1 50 MAGNETIC ASSEMBLY 1
18 COMPUTER 1 51 HEX HEAD BOLT 1
19 HANDLE BAR 1 52 FLYWHEEL 1
20
HAND PULSE WIRE LOWER
2 53 IDLER PULLEY 1
21 CLAMP 1 54 SPRING 1
22 ALLEN SCREW M8*20 2 55 HEX HEAD NUT M8 1
23 T TYPE KNOB 1 56 HEX HEAD BOLT 1
24 SELF-TAPPING SCREW ST4*20 2 57 CHAIN COVER L/R 1/1
25 FLAT WASHER Φ4.2*Φ12*1 2 58 END CAP FOR CHAIN COVER 2
26 HAND PULSE SENSOR 2 59 HEX HEAD BOLT M6*25 1
27 FOAM GRIP FOR HANDLEBAR 2 60 HEX HEAD NUT M6 2
28 SEAT POST 1 61 SLIDING SEAT 1
29 NYLON NUT M8 5 62 CARRIAGE BOLT M8*40 1
30 SPRING WASHER Φ8 3 63 BELT 1
31 FLAT WASHER Φ8*Φ17*1.5 4 64 KNOB 1
32 TENSION CABLE LOWER 1 65 SENSOR WIRE LOWER 1
33 CLAMP COVER 1

4
EXPLODED DIAGRAM
2
3
44
44
5
6
6
1
78
7
7
7
8
8
8
9
10
35
35
12
13
14
15
10
192021
2223
25
24
27
2425
26
2711
32
33
34R
34L
36
36
37
28
3031
29
64
16
17
62
61
41L
3
65
18

5
43
39
40
47
42
2231
29
29
39
39
39
40
40
44
45
51
50
49
49
53
55
56
57L
57R
58
58
59
60
38
46
46
52
54
63
41L
41R
46
46
48
48

6
HARDWARE PARTS LIST
No. Description Drawing Q’ty
4 Carriage Bolt M10*65 4
7 Curve Washer Φ10*Φ22 4
8 Domed Nut M10 4
10 Allen Bolt M8*16 4
23 T type Knob 1
33 Clamp cover 1
35 Curve Washer Φ8*Φ20 4
Allen Key 6mm 1
Box Wrench 1
Above described parts are all the parts you need to assemble this machine. Before
you start to assemble, please check the hardware packing to make sure they are
included.

7
PRE-ASSEMBLY CHECK LIST
PART NO. DESCRIPTION Q’TY
1 Main Frame 1
2 Rear Stabilizer 1
5 Front Stabilizer 1
11 Seat 1
12 Front Post 1
18 Computer 1
19 Handlebar 1
28 Seat Post 1
34 Left & Right Pedal 1/1
User Manual 1
Hardware bag 1
NO.1 NO.5 NO.12
NO.18
NO.19
NO.11
NO.34
NO.28
NO.2
18

8
ASSEMBLY INSTRUCTION
STEP 1
(a) Attach front stabilizer (5) to main frame (1), tighten with 2 sets of carriage bolt (4), curve
washer (7) and domed nut (8).
(b) Then, attach rear stabilizer (2) to main frame (1), tighten with 2 sets of carriage bolt (4),
curve washer (7) and domed nut (8).
STEP 2
(a) Take front post (12) and connect middle sensor wire (14) with lower sensor wire (65).
(b) Adjust the tension control knob (13) to level 8, then connect it with the lower tension cable
(32). Insert front post (12) into main frame (1) and tighten with 4 sets of allen screw (10)
and curve washer (7).
8
8
1
2
44
13
10
7
10
7
32
13
12
14
3265
14
65

9
HOW TO CONNECT TENSION CONNECTOR
Slide the Cable wire from the
Upper Tension Connector in
between the opening on the
wire holder on the Lower
Tension Connector.
Pull the Upper Tension
Connector backward and slide
the wire through the slot on the
bracket.
Drop down the Connector so
the fitting sits firmly on top of
the bracket.
NOTE: In able to hold the Front Post while connecting the cables and wires，
extra help may be needed.

10
STEP 3
(a) Remove the clamp (21) and allen screw (22) from the front post . Attach handlebar (19) to
front post, Secure by using the clamp (21), allen screw (22), clamp cover (33) and T type
knob (23).
(b) Insert the hand pulse wires (20) through end cap for wire (37) and insert through the hole
in the front post, pull the hand pulse wires (20) through the hole at the top of the front post
and insert end cap for wire(37) into the front post.
(c) Connect the hand pulse wires (20) and middle sensor wire (14) to the back of the
computer (18) . Attach the computer onto the bracket of front post. Secure by using two
screws (15) which are pre-assembled on the back of computer.
STEP 4
Take the Quick release knob (9) off from main frame . Insert seat post (28) into the main
Frame (1), then tighten with knob (9).
Attach seat (11) to seat post, tighten with carriage bolt (62), square washer(17),spacer (16)
and knob (64).
1921
2223
18
20
33
928
11
64
16
17
62

11
STEP 5
The left pedal (34L) and right pedal (34R) which are marked "L" and "R". Connect them to
their appropriate crank arm (41). The right pedal is on the right hand side of the cycle as you
sit on it. Note that the right pedal should be threaded on clockwise and the left pedal on
counter-clockwise.
CHECK ALL BOLTS AND NUTS ARE TIGHTENED
BEFORE USING THE MACHINE
34R
34L
41L

12
COMPUTER INSTRUCTIONS
The monitor can only be power on with using the AA batteries.
FUNCTION BUTTONS
MODE
1. Press the button to select TIME, DISTANCE and CALORIES to preset.
2. Press the button for selection function display value on LCD, or enter after setting.
3. Press the button and hold for 2 seconds to reset all value except Odometer to be zero.
(When the user replace batteries, all the values will reset to ZERO automatically.)
SET
1. To set up the target value of TIME, DISTANCE and CALORIES.
2. Press the button and hold for 2 seconds to speed up the increment.
RESET
1. Press the button to reset function value when setting.
2. Press the button and hold for 2 seconds to reset all value except Odometer to be zero.
(When the user replace batteries, all the values will reset to ZERO automatically.)
FUNCTIONS & OPERATIONS
Time
Accumulates total time from 00:00 up to 99:59. The user may preset target time by
pressing SET & MODE button. Each increment is 1 minute.
Automatically count down from targeting value during exercise.
Calories
Accumulates calories consumption during training from 0 to max. 9999 calories. The user
may also preset the target calorie before training by press SET & MODE button. Each
setting increase is 1 cal till 1000, Each increment will be 10 cal when calories is over 1000.
Automatically count down from targeting value during exercise.
Note : This data is a rough guide which can not be used in medical treatment

13
Odometer
Display the total accumulated distance from 0.0 to 999.9. User also can press mode key to
display the Odometer value.
Pulse
The monitor will display the user's heart rate in beats per minute during training.
Speed
Displays your workout speed value in Kilometer per hour.
Distance
Displays the accumulative distance traveled during each workout up to a maximum of 99.9
MILE.
Note:
1. If the computer displays abnormally, please re-install the battery and try again.
2. Please install 2 pcs of AA 1.5V batteries in the battery case on the back of monitor.
(Whenever batteries are removed, all of the functions values will be reset to zero.)
3. The batteries must be removed from the appliance before it is scrapped and that they are
disposed of safely.
4. While the user starts to do exercise, the display will show out the workout value
automatically. Once stop exercise over 4 minutes, the display will turn off. But the workout
value of odometer will be hold. While user starts exercise again, workout value of
odometer will be accumulated continuously.
5. After the monitor is power on or press MODE key, the LCD will display all functions values
from Time – Calories – Odometer – Pulse – Speed – Distance. Each value will be held for
6 seconds.

GARLANDO SPA
Via Regione Piemonte, 32 - Zona Industriale D1
15068 - Pozzolo Formigaro (AL) - Italy
www.toorx.it - [e-mail]