TOORX SRX40S User manual

Ed : Rev : Cod :
INSTRUCTION
09/18 GRLDTOORXSRX40S
00

4
EXPLODED-VIEW & PARTS LIST：

5
NO NAME QUANTITY SPEC
1L PEDAL L 1 JD-301（9/16"）L
1R PEDAL R 1 JD-301（9/16"）R
2 END CAP1 4 70*30*1.5
3 CARRIAGE BOLT 4 GB/T 12-1988 M8*42
4 REAR STABILIZER 1 WELDING
5 FLAT WASHER 4 GB/T 95-2002 8
6 DOMED NUT 4 GB/T 802-1988 M8
(H=16mm)
7 SPRING ADJUSTMENT KNOB 2 φ57*62 (M16*1.5)
8 PLASTIC SLEEVE 2 60*30*1.5
9 FLAT WASHER 3 GB/T95-2002 12
10 VERTICAL SEAT POST 1 WELDING
11 END CAP2 2 40*20*1.5
12 SEAT POST 1 WELDING
13 SEAT 1 DD-2681
14 STOPPER 4 φ32*37/(M8X25)
15 FRONT STABILIZER 1 WELDING
16 MAIN FRAME 1 WELDING
17 HANDLEBAR POST 1 WELDING
18 HANDLE BAR 1 WELDING
19 SPRING WASHER 4 GB/T 859-1987 8
20 BOLT 8 GB/T 70.2-2000 M8*15
21 HANDLEBAR COVER 1 115*89*75 (60g)
22 B0TTLE HOLDER 1 117*85*90
23 BRAKE KNOB 1 112*32*7
24 END CAP 3 2 50*25*1.5
25 LOCKING KNOB 1 PE+Q235/φ52*47 (M8x15)
26 FLAT WASHER 1 1 φ32*φ8.2*2
27 ADJUSTMENT KNOB 1 φ38*79
28 FIXING NUT 1 2 GB/T 6177.2-2000 M10*1.25
29 CRANK END CAP 2 φ23*7.5
30 SHEET IRON 1 δ5
31 LOCK NUT 7 GB/T 889.1-2000 M8
32 LITTLE PLASTIC RING 1 14*8*9
33 RIGHT CRANK 1 170*27
34 CRANK COVER 1 φ56*28
35 BEARING 2 6004ZZ

6
NO NAME QUANTITY SPEC
36 LEFT CRANK 1 170*27
37 SENSOR 1 SR-202
38 FIXING NUT 2 2 GB/T 802-1988 M12X1.25
(H=16mm)
39 FIXING BOLT 2 M6*58
40 NUT 2 GB/T 889.1-2000 M6
41 SCREW 1 6 GB/T 845-1985 ST4.2*19
42 SCREW 2 4 GB/T 15856.1-2002 ST4.2X19
43 SCREW 3 5 GB/845-85 ST4.8X13
44 OUTER CHAIN COVER 1 654*263*49 (507g)
45 LITTLE CHAIN COVER 1 108*37*3 (7g)
46 AXIS 1 φ20*162
47 LONG FIXING TUBE 1 φ25*φ20.5*41
48 SHORT FIXING TUBE 1 φ25*φ20.5*9
49 INNER CHAIN COVER 1 451*260*2 (250g)
50 CHAIN 1 P=12.7，106
51 CHAIN WHEEL 1 P=12.7,Z=52T
52 BRAKE 1 2PCS 130mm
53 BOLT 1 GB/T 70.1-2000 M6*20
54 BRAKE PLASTIC 2 82*41*19
55 BOLT 2 GB/T 5780-2000 M8*40
56 WHEEL 2 φ50*23
57 NUT 4 GB/T 41-2000 M8
58 FIXING NUT 2 2 M12X1.25 H=6
59 FIXING TUBE 1 φ16*φ12.1*35
60 BEARING 2 6001ZZ
61 FLYWHEEL 1 φ453*72
62 FLYWHEEL SHAFT 1 φ12*160
63 PLASTIC RING 1 φ20*φ9*3
64 COMPUTER HOLDER 1 δ2.5
65 COMPUTER 1 HS-6065
66 FIXING NUT 2 27*M20*1（5mm）
67 WOOLLY BLOCK 2 78*38*6
68 END CAP 4 1 60*30*1.5
69 LOCK NUT 2 M33*1*4
70 CHAIN WHEEL 1 A7K-16 1/2"*1/8" 16T（1.37"）

7
FIG.1
ASSEMBLY INSTRUCTION:
1.PREPARATION:
A. Before assembling make sure that you will have enough space around the item.
B. Use the present tooling for assembling.
C. Before assembling please check whether all needed parts are available (at the above
of this instruction sheet you will find an explosion drawing with all single parts (marked
with numbers) which this item consists of.
2.ASSEMBLY INSTRUCTION:
:
FIG.2
FIG.2:
Slide the seat post (12) into the vertical
Seat post (10) and, at the desired
position, align holes and fix in place with
the Locking Knob (25) and flat washer
(26). Now fix the Seat (13) to the seat
post (12) as shown. Insert the vertical
Seat Post (10) into the main frame (16)
and line up the holes. Secure the
saddle in position with the Adjustment
Knob (7). The correct height for the seat
can be adjusted after the bike is fully
assembled.
FIG.1:
Attach the Front Stabilizer (pt.15)
to the Main Frame (pt.16) using two
sets of Ø8 Flat Washers (pt.5), M8
Domed Nut (pt.6) and M8*42 Carriage
bolt (3).
Attach the Rear Stabilizer (pt.4) to the
Main Frame (pt.16) using two sets of
Ø8 Flat Washers (pt.5), M8 Domed Nut
(pt.6) and M8*42 Carriage bolt (3).

8
FIG.3
FIG.4
FIG.4:
The Pedals (pt.1 L & pt.1 R) are
marked "L" and "R" - Left and Right.
Connect them to their appropriate
crank arms. The right crank arm is on
the right- hand side of the cycle as you
sit on it.
Note that the Right pedal should be
threaded on clockwise and the Left
pedal anticlockwise.
FIG.3:
Slide the Handlebar Post (pt.17) into the
handlebar post housing on the main
frame. You will have to slacken the
knurled section of the Spring Adjustment
Knob (pt.7) and pull the knob back and
then select and align holes for the desired
height. Release the knob and retighten
the knurled portion.
Remove the bolts and spring washer
from the Handlebar Post (pt.17), then fix
the Handlebar (pt.18) with 4pcs Ø8 the
Spring Washer (pt.19) and M8*15 the Bolt
(pt.20).
ATTENTION: YOU SHOULD FIX
THE HANDLEBAR TIGHTLY
Slide the Computer (pt.65) onto the
Computer Holder (pt.64)
connect the plug (A1&A2),

ADJUSTMENT
*To adjust the seat height, slacken the spring knob on the vertical post
stem on the main frame and pull back the knob. Position the vertical
seat post for the desired height so that holes are aligned, then release
the knob and retighten it.
*To move the seat forward in the direction of the handlebar or
backwards away from it, loosen the adjusting knob and washer and
pull the knob back. Slide horizontal seat post into desired position.
Align holes and then retighten the adjusting knob.
*To adjust the handlebar height, slacken the spring knob and secondary
knob and pull both knobs back. Slide the handlebar post along the
housing on the main frame to the desired height and, with the holes
aligned correctly, tighten the spring adjusting knob and then the
secondary knob.

GARLANDO SPA
Via Regione Piemonte, 32 - Zona Industriale D1
15068 - Pozzolo Formigaro (AL) - Italy
www.toorx.it - [e-mail]