TOORX BRX 100 User manual

Edizione : Revisione : 00
INSTRUCTION
08/16 00

1
Dear Customers,
We want to thank you for having chosen a Magnetic Bike and wish
you a lot of fun and success during training.
Please note and follow the enclosed safety and assembly instructions
carefully.
If you have questions please do not hesitate to contact us.
Table of Content as blew:
1.) Safety Instruction
2.) Exploded Drawing
3.) Parts List
4.) Assembly Instruction
5.) Computer Instruction

4
EXPLODED DRAWING
B
A

5
PART LIST
Part #
Description
Quantity
1
Computer
1
2
Upper computer cable
1
3
Screw
4
4L
Computer plastic cover (Left)
1
4R
Computer plastic cover (Right)
1
5
Screw
8
6
Self-tapping screw
2
7
Saddle
1
8
Tube spacer
1
9
Round-shaped Knob
1
10R
Seat post plastic cover (Left)
1
10L
Seat post plastic cover (Right)
1
11
Screw
2
12
Seat post
1
13
Tube bundle
1
14
Round head grooved pin
1
15
Tension cable
1
16
Lower computer cable
1
17
Sensor set
1
18
Sensor
1
19
Main frame
1
20
Bearing
3
21
Washer
1
22
Waved washer
1
23
C shape washer
1
24
Round head grooved pin
1
25
Slide tube
1
26
Nut
1
27
Tube end cap
2
28L
Chain cover (Left)
1
28R
Chain cover (Right)
1

6
Part #
Description
Quantity
29
Self-tapping screw
6
30L
Crank (Left)
1
30R
Crank (Right)
1
31
Anti-loose hex head bolt
2
32
Crank end cap
2
33L
Pedal (Left)
1
33R
Pedal (Right)
1
34
Screw
8
35
Joint lever
3
36
Hex screw
2
37
Spring washer
2
38
Washer
2
39
Axle for flywheel holder
1
40
Nut
2
41
Hex screw
1
42
Tapered spring
1
43
Manget set
1
44
Washer
1
45
Washer
1
46
Rear end cap
2
47
Rear Stabilizer
1
48
Flat washer
10
49
Allen bolt
4
50
DC line
1
51
Spring washer
10
52
Washer
1
53
Belt wheel
1
54
Belt
1
55
Pedal Axle
1
56
Allen head screw
3
57
Upper protective cover
1
58L
Front end cap Left
1
58R
Front end cap Right
1

7
Part #
Description
Quantity
59
Front Stabilizer
1
60
Motor
1
61
Allen bolt
7
62
Curved washer
2
63
Handlebar post
1
64
Hand pulse pads
2
65
Self-tapping screw
2
66
Handlebar foam
2
67
Hand pulse cable
2
68
End cap
2
69
Handlebar
1
70
Nut
2
71
Idler
1
72
Waved washer
1
73
Idler rack
1
74
Spring
1
75
Spring
2
76
Bearing
1
77
Washer
1
78
Flywheel
1
79
Oneway bearing
1
80
Bearing
1
81
Axle for flywheel
1
82
Small belt wheel
1
83
Bearing
1
84
Nut
2
85
Allen key wrench
1
86
Combination wrench
1
87
Adaptor
1

8
ASSEMBLY INSTRUCTION
STEP 1
Attach the Front Stabilizer (59) onto the Main Frame (19) with Flat washer
(48), Spring washer (51) and M8 Allen bolt (49).Tighten fully.
Attach the Rear Stabilizer (47) onto the Main Frame (19) with Flat washer
(48), Spring washer (51) and M8 Allen bolt (49).Tighten fully.
Note：You can adjust the Rear End Cap to keep the Magnetic Bike stable.

9
STEP 2
Pull out the Upper protective cover (57) from the Main frame (19) and
attach it to the Handlebar post (63) shown as right image
Connect the Upper Computer Cable (2) with Lower Computer Cable (16)
shown as the left top image.
Attach the Handlebar Post (63) onto the Main Frame (19) with M8 Allen
Bolts (61), Spring Washers (51), Flat washer (48) or Curved Washers (62).
Tighten fully. Then slide down the Upper protective cover (57).

10
STEP 3
Assemble the saddle (7) to the adjustable Seat post (12) by the nut shown
as the left image.
Place the Seat Post (12) into the Main Frame (19), set it at the desired
position and lock it by inserting Round head grooved pin (14) in place and
tighten fully.
The setting of the seat post can be adjusted up and down easily as
desired later through turning and pulling the Round head grooved pin (14).
The user could adjust the saddle backward and frontward as well by
adjusting the knob (24). See the right images.

11
STEP 4
Assemble the pedals Left and Right (33L) & (33R) to the crank Left and
Right (30L) & (30R).
Attach the Handlebar (69) onto the Handlebar Post (63) with Tube Spacer
(8) and Round-shaped Knob (9).Tighten fully.
Remember to pull the Hand pulse cable (67) through the hole above
Handlebar holder plate (63) and extent to the upright position, see the right
image.