Tormach 33318 Technical manual

Page 1
Tormach Inc.
1071 Uniek Drive, Waunakee, WI 53597
Phone: [phone] / Fax: [phone]
©Tormach® 2014. All rights reserved.
Specicaons subject to change without noce.
TD10244_Lathe_Arm_Install_0216A
Lathe Arm Installation
Product Idencaon: 15L Slant-PRO Lathe Arm Installaon Kit (PN 33318)
Purpose: This document details installaon of the lathe arm assembly on the 15L Slant-PRO Lathe (with or
without the full enclosure installed).
Qty.Lathe Arm Installation Kit
1 Square Tube Arm w/ 4-hole Mounting Clevis
1 Round Monitor Post
1 Monitor Mounting Plate
48 mm Socket Head Cap Screws w/ Lock and Flat
Washers
45 mm Socket Head Cap Screws w/ Lock and Flat
Washers
4Wood Screws (for optional mounting of E-stop to
table)
10 4 mm Flat Head Screws
4Wire Tie Mounts
4Wire Ties
2 E-stop Cable Clips
1Keyboard Table
NOTE: If any of these items are missing, contact Tormach
Customer Service at [phone] for a replacement.
NOTE: Some kits contain both a short and a long Square Tube Arm. The operator may use either, but the
longer tube is recommended when the full enclosure is installed. Some parts in this kit may not be used.
Optional Prodcts PN
USB Bulkhead Port Assembly 31289
17” LCD Monitor 30615
17” Touch Screen Kit 35575
Mini Keyboard 31371
Keyboard Cover 31384
Jog Shuttle 30616

Page 2
Tormach Inc.
1071 Uniek Drive, Waunakee, WI 53597
Phone: [phone] / Fax: [phone]
©Tormach® 2014. All rights reserved.
Specicaons subject to change without noce.
TD10244_Lathe_Arm_Install_0216A
Lathe Arm Installation
1. Power o lathe according to Power O/On Procedure detailed below.
WARNING! Electrical Shock Hazard: Be sure to power down machine before making any electrical
modicaons. Failure to do so may result in personal injury or death.
Power Off/On Procedure
Power Off
1. Push red E-stop button in
2. Click Exit on screen; when prompted click OK to power off
3.Turn Main Disconnect Off (see image at right)
Power On
1.Turn Main Disconnect On (see image at right)
2.After software loads, t urn red E-stop clockwise to release
3. Press green Start button
4. Click Reset on screen
2. Locate the four pre-tapped pilot holes used
to aach the 4-hole Mounng Clevis to the
lathe; aach with four long 8 mm Socket
Head Cap Screws, Nuts, and Washers (see
Figure 1).
NOTE: Before nalizing the mounng locaon,
inspect the inside of the lathe’s controller door to
ensure there are no obstrucons.
IMPORTANT! The Square Tube Arm must be
installed with the cable slots facing the rear of the
lathe, as shown in Figure 1.Figure 1
4-hole Mounting Clevis
Square Tube Arm
Cable
Slots

Page 3
Tormach Inc.
1071 Uniek Drive, Waunakee, WI 53597
Phone: [phone] / Fax: [phone]
©Tormach® 2014. All rights reserved.
Specicaons subject to change without noce.
TD10244_Lathe_Arm_Install_0216A
3. Insert the Round Monitor Post into the Square Tube
Arm and ghten the cross bolt (see Figure 2). The
working height of the post can be adjusted aer
the keyboard and monitor are aached. Note the
orientaon of holes along the inside of the Round
Monitor Post (see Figure 2).
4. If not already installed, use a mallet to tap the End
Plug into the Square Tube Arm (see Figure 3).
Figure 2
Figure 3
End Plug

Page 4
Tormach Inc.
1071 Uniek Drive, Waunakee, WI 53597
Phone: [phone] / Fax: [phone]
©Tormach® 2014. All rights reserved.
Specicaons subject to change without noce.
TD10244_Lathe_Arm_Install_0216A
5. Posion the Round Monitor Post for mounng
of the Keyboard Table as shown in Figure 4
and Figure 5. Tighten the applicable screws
to hold the desired mounng posion.
6. Locate the four E-stop (emergency stop) holes on the underside of the Keyboard Table (see Figure 5).
IMPORTANT! The Keyboard Table must be installed with the four E-stop holes facing down (underside of
table), as shown in Figure 5, Figure 6, and Figure 9. These holes are used for mounng the E-stop box
(included with lathe).
7. Using the four 5 mm Socket Head Screws, aach the Keyboard Table to the Round Monitor Post (see
Figure 5 and Figure 6).
Figure 4
Figure 5
E-stop
Holes
Figure 6

Page 5
Tormach Inc.
1071 Uniek Drive, Waunakee, WI 53597
Phone: [phone] / Fax: [phone]
©Tormach® 2014. All rights reserved.
Specicaons subject to change without noce.
TD10244_Lathe_Arm_Install_0216A
8. Fasten Wire Tie Mounts to the Round Monitor
Post using four 4 mm Flat Head Screws (see
Figure 7).
9. Connect E-stop Cable Clips to the boom of the
Square Tube Arm using two 4 mm Flat Head
Screws (see Figure 8).
10. Aach the monitor (sold separately) to the
monitor post assembly and route cables.
NOTE: Tormach recommends all cable connecons be
wrapped in electrical tape.
11. Adjust monitor height and keyboard angle as
needed.
12. Using the four Wood Screws, mount the remote
E-stop (included with lathe) to the underside of
the keyboard table (see Figure 9).
Figure 7
Figure 8 Figure 9