Toro 112-9248 User manual

FormNo.3416-524RevA
PullLinkKitforDPAReelMowerGroomer
Greensmaster®3250-DSeriesTractionUnit
ModelNo.112-9248
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCalifornia
tocausecancer,birthdefects,orreproductiveharm.
Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
Installation
1
PreparingtheMachine
NoPartsRequired
Procedure
1.Parkthemachineonalevelsurface.
2.Engagetheparkingbrake.
3.Shutofftheengineandremovethekey.
2
InstallingtheFrontCarrier
Frames
Partsneededforthisprocedure:
2Rightlinkbracket
2Leftlinkbracket
4Carriagebolt
4Flatwasher
4Locknut
4Bushing
4Longpull-armextension
4Bolt—3/8x1-1/2inches(2006andearliermachines
only)
4Rollershaft(2007andaftermachinesonly)
4Bolt—3/8x2inches(2007andaftermachinesonly)
8Bushing(2007andaftermachinesonly)
2006andEarlierMachines
1.Slidebackthesleeveontheball-jointreceiver
andremovethereceiverfromtheballstud
(Figure1).
©2017—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3416-524*A

g218544
Figure1
1.Rollershaft7.Flatwasher
2.Ballstud8.Spacer
3.Ball-jointreceiver9.Bushing
4.Jamnut10.Pull-linkassembly
5.Pull-linkextension11.Anti-scalproller
6.Bolt
2.Removetheboltsandrollershaftssecuringthe
anti-scalprollersandthepull-linkassembliesto
eachcarrierframe(Figure1).
3.Disassemblethepull-linkassemblies(Figure1).
4.Threadthepreviouslyremovedjamnutonto
eachofthenewlongerpull-armextensions
andontotheexistingpull-linkandbushing
assemblies(Figure2)
g218546
Figure2
1.Rollershaft9.Spacer
2.Ballstud10.Bushing
3.Ball-jointreceiver11.Pull-linkliner
4.Jamnut12.Pull-linkassembly
5.Longpull-linkextension13.Linkbracket
6.Carriagebolt14.Bolt(3/8x1-1/2inches)
7.Locknut15.Anti-scalproller
8.Flatwasher
5.Assemblethenewlongerpull-armextensionsto
theexistingpull-linkassembliesandball-joint
receiverassemblies(Figure2).Donottighten
thejamnutsatthistime.
6.Mounttheappropriatelinkbracket(leftorright)
andapreviouslyremovedanti-scalprollerto
theendofeachfrontcarrierframewithanew
carriageboltandthepreviouslyremovedroller
shaft.PositionthebracketsasshowninFigure
2.
7.Mountapull-linkassemblytotheoutsideofeach
linkbracketwithabolt(3/8x1-1/2inches),at
washer,bushing,thepreviouslyremovedspacer
andatwasher,andanewlocknut(Figure2).
Note:Makesurethatthebushingisinsidethe
pull-linkassembly.
8.Slidebackthesleeveontheball-jointreceivers
andinstallthereceiversontotheballstuds
(Figure2).
9.Mountabasketontothecarrierframe.
10.Adjustthepullarmsuntilthereisa6to10mm
(1/4to3/8inch)clearancebetweenthelipofthe
basketandthereelblades.
2

Note:Makesurethebasketlipsareparallel
withthereelbladesallthewayacrossthereel
blades.
11.Tightenthejamnuts.
2007andLaterMachines
1.Slidebackthesleeveontheball-jointreceiver
andremovethereceiverfromtheballstud
(Figure3)
g218641
Figure3
1.Ballstud7.Bushing
2.Ball-jointreceiver8.Pull-linkassembly
3.Jamnut9.Spacer
4.Pull-linkextension10.Anti-scalproller
5.Locknut11.Rollershaft
6.Flatwasher
2.Removethelocknutsandrollershaftssecuring
theanti-scalprollersandthepull-linkassemblies
toeachcarrierframe(Figure3).
3.Disassemblethepull-linkassemblies(Figure3).
4.Threadapreviouslyremovedjamnutontoeach
ofthenewlongerpull-armextensionsandonto
theexistingpull-linkandbushingassemblies
(Figure4).
g218652
Figure4
1.Rollershaft8.Flatwasher
2.Ballstud9.Bushing
3.Ball-jointreceiver10.Spacer
4.Jamnut11.Pull-linkassembly
5.Longpull-linkextension12.Linkbracket
6.Carriagebolt13.Bolt(3/8x2inches)
7.Locknut14.Anti-scalproller
5.Assemblethenewlongerpull-armextensionsto
theexistingpull-linkassembliesandball-joint
receiverassemblies(Figure4).Donottighten
thejamnutsatthistime.
6.Mounttheappropriatelinkbracket(leftorright)
andapreviouslyremovedanti-scalproller
totheendofeachfrontcarrierframewitha
newcarriageboltandrollershaft.Positionthe
bracketsasshowninFigure4.
7.Mountapull-linkassemblytotheoutsideofeach
linkbracketwithanewbolt(3/8x2inches),
previouslyremovedatwasher,2newbushings,
apreviouslyremovedspacer,atwasherand
locknut.Positionthecomponentsasshownin
Figure4.
Note:Makesurethatthebushingsareinside
thepull-linkassembly.
8.Slidebackthesleeveontheball-jointreceivers
andinstallthereceiversontotheballstuds
(Figure4).
9.Mountabasketontothecarrierframe.
10.Adjustthepullarmsuntilthereisa2to3mm
(1/16to1/8inch)clearancebetweenthelipof
thebasketandthereelblades.
3

Note:Makesurethatthebasketlipsare
parallelwiththereelbladesallthewayacross
thereelblades.
11.Tightenthejamnuts.
3
InstallingtheRearCarrier
Frame
Partsneededforthisprocedure:
2Shortpull-armextension
Procedure
1.Slidebackthesleeveontheball-jointreceiver
andremovethereceiverfromtheballstud
(Figure5).
g218561
Figure5
1.Ballstud3.Jamnut
2.Ball-jointreceiver4.Shortpull-linkextension
2.Loosenthejamnutsandremovethepull-arm
extension(Figure5).Removethejamnutsfrom
thepull-armextension.
3.Installthenewshorterpull-armextensionwith
thepreviouslyremovedjamnuts(Figure5).Do
nottightenthejamnuts.
4.Adjustthepullarmsuntilthereisa6to10mm
(1/4to3/8inch)clearancefor2006andearlier
machines,ora2to3mm(1/16to1/8inch)
clearancefor2007andaftermachines,between
thelipofthebasketandthereelblades.
Note:Makesurethatthebasketlipsare
parallelwiththereelbladesallthewayacross
thereelblades.
5.Tightenthejamnuts.
4