Toro Maxi Sneaker 370 User manual

Operator’s Manual
Hydra Borer
Maxi Sneaker 370 Vibratory Plow
Model
25532E
25532T
3462-340A Original Instructions (EN) *3462-340*A

Chapter 1
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.
Safety Decal Location
G434640
Decal147-5746
Decal Part: 147-5746
decal147-5746
Rotating shaft hazard; keep away
from moving parts.
Safety and Instructional Decals Page 1–1 3462-340 A

Decal Part: 147-5747
decal147-5747
Decal Part: 147-5748
decal147-5748
Push the lever forward to rotate the
drill clockwise; Pull the lever rearward to
rotate the drill counterclockwise.
3462-340A Page 1–2 Safety and Instructional Decals: Safety Decal Location

Chapter 2
Installation
1Installing the Hydra Borer Motor
Parts Required
1 Motor
1 Adapter
1 Retainer adapter
1 Lock washer
1 Bolt (1/2 x 1-1/4 inches)
2 90-degree elbow connector
1 Motor bracket
8 Bolt (1/2 x 1-3/4 inches)
8 Flat washer (1/2 inch)
8 Locknut (1/2 inch)
1 U-Joint assembly
1 U-Joint adapter
1 Bolt (3/8 inch x 2-1/2 inches)
1 Nut (3/8 inc)
Installation Page 2–1 3462-340 A

G433933
1. Grease the shaft of the motor and place the
adapter onto the motor
2. Install the adapter and retainer adapter
on the motor.
3. Place the lock washer on the bolt and
apply thread-locking adhesive to the bolt.
4. Secure the bolt to the adapters and torque to
160 to 165 N⋅m (118 to 122 ft-lb).
G433934
5. Install 90-degree elbow connectors into the
ports on the motor
G434022
6. Secure the motor to the motor bracket using 4
bolts (1/2 x 1-3/4 inches), 4 flat washers (1/2
inch), and 4 locknuts (1/2 inch).
7. Torque the bolts to 91 to 113 N⋅m (67 to 83 ft-
lb).
3462-340A Page 2–2 Installation: Installing the Hydra Borer Motor

G434070
8. Secure the motor assembly to the machine
using 4 bolts (1/2 x 1-3/4 inch), 4 flat washers
(1/2 inch), and 4 locknuts (1/2 inch)
G434071
9. Install the U-Joint assembly and adapter to the
motor assembly using a bolt (3/8 x 2-1/2
inches) and a nut (3/8 inch).
2Installing the Hydraulic Valve
Parts Required
1 Valve
1 Knob
2 Nuts (M10)
1 Lever
1 Valve bracket
3 Bolt (M8)
3 Nut (M8)
1 90-degree connector
2 45-degree connector
2 Straight connector
Installation: Installing the Hydraulic Valve Page 2–3 3462-340 A

G434083
1. Install the handle lever to the hydraulic valve
using 2 nuts (M10) and the knob.
G434082
2. Install the 90-degree connector , 2 45-
degree connector , and 2 straight connector
to the valve .
G434084
3. Install the valve assembly to the bracket using
3 bolts (M8) and 3 nuts (M8).
G434085
4. Remove the panel on the left side of the
machine. Secure the valve assembly to the
machine using the bolts, but do not fully tighten
them.
3462-340A Page 2–4 Installation: Installing the Hydraulic Valve

3Installing the Hoses
Installing the Motor and Plow Hoses
Parts Required
1 54-inch hydraulic hose
1 53-inch hydraulic hose
1 P-Clamp
1 Bolt (5/16 x 1 inch)
1 Nut (5/16 inch)
Figure 1 Routing Overview
G434138
G434135
1. Connect the 54-inch hose to the top
connector on the motor.
2. Connect the 53-inch hose to the lower
connector on the motor.
3. Secure the hoses to the inside of the frame
with the P-clamp .
4. Remove the left hood.
Installation: Installing the Hoses Page 2–5 3462-340 A

Installing the Motor and Plow Hoses (continued)
G434136
5. Route the hoses up through the machine
toward the valve.
G434137
6. Connect the 54-inch hose to the lower straight
connector on the valve.
7. Connect the 53-inch hose to the 90-degree
connector on the valve.
G434195
8. Disconnect the hose from the 90-degree
connector on the tandem pump and connect it
to the 45-degree connector on the hydra borer
valve.
3462-340A Page 2–6 Installation: Installing the Hoses

Installing the Hoses without a Trencher
Parts Required
1 Medium hardline
1 18-inch hose
1 90-degree union connector
G434258
1. Install the medium hardline to the 45-degree
connector on the hydraulic valve.
G434287
2. Connect the 90-degree union connector to
the 18-inch hose.
3. Connect the 18-inch hose from the tandem
pump to the straight connector on the hydraulic
valve.
4. Fully tighten the hydraulic valve assembly
mounting hardware; torque the nuts to 23 to
29 N⋅m (17 to 21 ft-lb).
Installation: Installing the Hoses Page 2–7 3462-340 A