Toro 136-4360 User manual

FormNo.3413-386RevA
SkidPlateKit
Groundsmaster®4000or4100SeriesRotaryMower
ModelNo.136-4360
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
Installation
1
PreparingtheMachine
NoPartsRequired
Procedure
1.Parkthemachineonalevelsurface.
2.Lowerthecuttingunits.
3.Engagetheparkingbrake.
4.Shutofftheengineandremovethekey.
5.Useajacktoraisethemachine.
Note:Therearejackingpointslocatedatthefront
andrearofthemachine;refertotheOperator’sManual
foryourmachine.
DANGER
Mechanicalorhydraulicjacksmayfailtosupport
machineandcauseaseriousinjury.
•Usejackstandswhensupportingmachine.
•Donotusehydraulicjacks.
2
InstallingtheSkidPlates
Partsneededforthisprocedure:
2Outer-rearskidplate
1Rearskidplate
2Frontskidplate
4Lockwasher
4Hex-socketscrew
4Spring-coilwasher
4Bolt(M10x30mm)
4Bolt(3/8-16x4inches)
4Flangenut
InstallingtheRearSkidPlates
1.Removetheexistinghardware(4boltsand4washers)
fromthemountplateasshowninFigure1.
©2017—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.OriginalInstructions(EN)
PrintedintheUSA.
AllRightsReserved*3413-386*A

g204660
Figure1
1.Bolt—existinghardware2.Washer—existing
hardware
2.Use4bolts(M10x30mm)and4spring-coilwashersto
securetherearskidplatetothemountplate(Figure2).
g204659
Figure2
1.Bolt(M10x30mm)3.Rearskidplate
2.Spring-coilwasher
3.Remove2boltsfromtheaxlecapsonbothsidesofthe
machine(Figure3).
g207711
Figure3
RightSideShown
1.Bolt3.Axle
2.Axlecap
4.Use2hex-socketscrewsand2lockwasherstosecure
theouter-rearskidplatestotheaxlecapsonbothsides
ofthemachine(Figure4).
g204658
Figure4
RightSideShown
1.Hex-socketscrew3.Outer-rearskidplate
2.Lockwasher4.Axlecap
2

InstallingtheFrontSkidPlates
1.Removetheexistinghardware(2boltsand2nuts)fromthemanifoldontheleftsideofthemachine(Figure5)
g205111
Figure5
LeftSideShown
1.Bolt—existinghardware5.Bolt(3/8-16x4inches)
2.Manifold6.Frontskidplate
3.Hubbracket7.Flangenut
4.Nut—existinghardware
2.Aligntheholesinafrontskidplatewiththeholesinthemanifold(Figure5).
3.Use2bolts(3/8-16x4inches)and2angenutstosecurethefrontskidplatetothehubbracket(Figure5).
3

4.Repeatsteps1through3toinstalltheotherfrontskidplatetotherightsideofthemachine(Figure6).
g205112
Figure6
RightSideShown
1.Bolt—existinghardware5.Bolt(3/8-16x4inches)
2.Manifold6.Frontskidplate
3.Hubbracket7.Flangenut
4.Nut—existinghardware
4