Toro 133-0609 User manual

FormNo.3404-252RevA
ROPSBeaconKit
Workman®MDorHDSeriesUtilityVehicle
ModelNo.133-0609
InstallationInstructions
WARNING
CALIFORNIA
Proposition65Warning
ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato
causecancer,birthdefects,orreproductiveharm.
Safety
SafetyandInstructionalDecals
Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential
danger.Replaceanydecalthatisdamagedorlost.
120-0771
1.Beacon
121-1702
1.Beacon—10A
©2016—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.T oro.com.OriginalInstructions(EN)
PrintedintheUSA
AllRightsReserved*3404-252*A

Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescriptionQty.Use
1Nopartsrequired–Preparethemachine.
Wireharness1
2Cabletie8Routethewireharness.
Beaconbracket1
U-bolt2
Flangenut(3/8inch)4
Beaconsocket1
3
Beaconassembly1
Installthebeaconassembly.
Rockerswitch1
4Beacon-lightdecal1Installtherockerswitch.
Fuse(10A)1
5Fusedecal1
Connectthewireharnesstothe
ground-blockterminalandinstallthe
fuse.
6Nopartsrequired–Connectthebattery.
7Nopartsrequired–Testthebeaconfunction.
1
PreparingtheMachine
NoPartsRequired
Procedure
1.Parkthemachineonalevelsurface,settheparking
brake,shutofftheengine,andremovethekey.
2.Disconnectthenegativebatterycable;refertoyour
Operator’sManual.
3.Openthehood.
2
RoutingtheWireHarness
Partsneededforthisprocedure:
1Wireharness
8Cabletie
2

ForMDUtilityVehicles
RoutethewireharnessasshowninFigure1andsecurethewireharnesstothemachinewithcabletiesasnecessary.
Figure1
3

ForHDUtilityVehicles
RoutethewireharnessasshowninFigure2andsecurethewireharnesstothemachinewithcabletiesasnecessary.
Figure2
4

3
InstallingtheBeacon
Assembly
Partsneededforthisprocedure:
1Beaconbracket
2U-bolt
4Flangenut(3/8inch)
1Beaconsocket
1Beaconassembly
Procedure
1.Looselysecurethebeaconbrackettothesideofthe
ROPSpostwiththe2U-boltsand4angenuts(3/8
inch)asshowninFigure3.
Figure3
1.U-bolt4.Flangenut(3/8inch)
2.Beacon5.Beaconbracket
3.Beaconsocket
2.Mountthebeaconsockettothebeaconbracketwith
theincludedjamnut(Figure3).
3.Plugthebeaconintothesocketandtightenthewing
nut(Figure3).
4
InstallingtheRockerSwitch
Partsneededforthisprocedure:
1Rockerswitch
1Beacon-lightdecal
Procedure
1.Removetheplasticplugfromtheleftsideofthedash
(Figure4).
Figure4
1.Plasticplug
2.Inserttherockerswitchintotheopeningandapply
thebeacon-lightdecaltotheleftoftherockerswitch
(Figure5).
Figure5
1.Beacon-lightdecal2.Rockerswitch
3.Connectthefemaleconnectorattachedtothewire
harnesstotherocker-switchblades(Figure6).
5

Figure6
1.Rocker-switchblades2.Femaleconnector
5
ConnectingtheWireHarness
totheGround-BlockTerminal
andInstallingtheFuse
Partsneededforthisprocedure:
1Fuse(10A)
1Fusedecal
Procedure
1.Insertthefuse(10A)intothefuseblockandapplythe
fusedecalbeneaththefuseblock(Figure7).
Figure7
1.Fuseblock3.Fuse(10A)
2.Fusedecal
2.Connectthewire-harness-terminalringtothe
ground-blockterminal(Figure8).
Figure8
1.Wire-harness-terminalring2.Ground-blockterminal
6
ConnectingtheBattery
NoPartsRequired
Procedure
Connectthenegativebatterycable;refertoyourOperator’s
Manual.
7
TestingtheBeacon
NoPartsRequired
Procedure
PushtherockerswitchuptoturnthebeacontotheON
position.
PushtherockerswitchdowntoturnthebeacontotheOFF
position.
6

Notes:
7