Tot Mate TM2181R User manual

channels
channel
1
#0964-3127
3594.TM2181.9/25/18
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.
CAUTION – CHOKING HAZARD
Adult assembly required due to presence
of small parts and sharp edges.
ATTENTION
Please unpack and assemble in an area away from children's activities. Remove all tools
and excess materials from work area after assembly of unit is complete. Dispose of pallet
and packaging materials in an environmentally friendly manner. If any parts are missing
or damaged, please call Stevens for immediate parts replacement (1-800-350-3270).
When ordering parts, give the Model Number and Color of the unit.
by Stevens Industries, Inc.
704 West Main St.
Teutopolis, IL 62467
P: 800.350.3270
P: 217-857-7100 • F: 217-857-7101
www.totmate.com
TM2181R
TM2181R
Book/Toy Storage
076,QYHQWRU\3DUWV/LVW
3DUWV/LVW
3$5747<,7(0
;;
;;
;;
;;


'(6&5,37,21
5DLO)U%D
(QG8
%RWWRP
'LYLGHU
70%DFN&OHDU[[
6FUHZ&RQQ+['F1LPP[PP
2-PERSON ASSEMBLY RECOMMENDED.
IMPORTANT!
Be sure to keep all parts supported
during assembly to avoid damage.
Do not over-tighten screws or it will
damage the pre-drilled holes;
snug fit is adequate.
HARDWARE / TOOLS INCLUDED
Confirmat Bolt (6)
(Screw Conn HxDc Ni 7mmx50mm)
Hex Wrench

TM2181R
STEP-BY-STEP ASSEMBLY
2#0964-3127
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TM2181.9/25/18
Lay Bottom (3) flat on floor, with routed channels
facing up.
STEP
1
Lay one End (2) flat on floor, with side having the
most holes facing up.
STEP
4
Insert dowel on one Rail (1) into lower hole at top
of End (2). Make sure routed channel on Rail (1)
is facing bottom of End (2). Press Rail (1) firmly
into place. Repeat with other Rail (1).
STEP
5
2-PERSON ASSEMBLY RECOMMENDED.
IMPORTANT!
Be sure to keep all parts supported during assembly to avoid damage.
Do not over-tighten screws or it will damage the pre-drilled holes;
snug fit is adequate.
Insert dowels on Divider (4) into holes on Bottom
(3). Press firmly into place.
STEP
2
Secure Bottom (3) to Divider (4) with Confirmat
Bolt (6), using the included Hex Wrench. This
assembly will be used in Step 6.
STEP
3
channels
top edge
channels
Using the assembly from Step 3, insert dowels on
Bottom (3) into remaining holes on End (2). Rails
(1) will fit into notches at top of Divider (4). Press
Bottom (3) firmly into place.
STEP
6

TM2181R
STEP-BY-STEP ASSEMBLY
3
#0964-3127
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TM2181.9/25/18
Remove plastic film from clear acrylic Backs (5).
Slide one Back (5) into channel on one Rail (1)
and corresponding channel on Bottom (3). Slide
other Back (5) into other set of channels. Seat
Backs (5) firmly against End (2).
STEP
7
Position other End (2) on top of assembly, so
dowels on Rails (1) and Bottom (3) align with
holes on End (2). Press firmly into place.
STEP
8
Secure End (2) to Rails (1) and Bottom (3) with
four Confirmat Bolts (6).
STEP
9
Carefully turn unit over, so other End (2) is facing
up.
STEP
10
Repeat Step 9 to secure End (2) to Rails (1) and
Bottom (3).
STEP
11

TM2181R
STEP-BY-STEP ASSEMBLY
4#0964-3127
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TM2181.9/25/18
Secure Rails (1) to Divider (4) with two Confirmat
Bolts (6).
STEP
12
Ensure that all joints and bolts are tight.
STEP
14
This completes the assembly.
Carefully stand unit upright.
STEP
13