Tot Mate TML402R User manual

1
#0964-3194
3594.TML402.10/26/18
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.
CAUTION – CHOKING HAZARD
Adult assembly required due to presence
of small parts and sharp edges.
ATTENTION
Please unpack and assemble in an area away from children's activities. Remove all tools
and excess materials from work area after assembly of unit is complete. Dispose of pallet
and packaging materials in an environmentally friendly manner. If any parts are missing
or damaged, please call Stevens for immediate parts replacement (1-800-350-3270).
When ordering parts, give the Model Number and Color of the unit.
by Stevens Industries, Inc.
704 West Main St.
Teutopolis, IL 62467
P: 800.350.3270
P: 217-857-7100 • F: 217-857-7101
www.totmate.com
TML402R
IMPORTANT!
Assembly must be securely attached to
building structure with anchoring devices
of appropriate type, size and quantity in
accordance with applicable codes and
accepted installation practices.
TML402R
3-Section Wall Locker
076,QYHQWRU
\
3DUWV/LVW
3DUWV/LVW
3$5747<,7(0
;;
;;
;;
;;
;;
;;
;;
;;




'(6&5,37,21
(QG/
(QG5
7RS%RW
%DFN
6KHOI0LG
6WULQJHU
'LYLGHU6KRUW
'LYLGHU/RQJ
+RRN$GYWJ&RDW'EO+RU]1L
6FUHZ7DSS3K2Y1,[
6FUHZ&RQQ+[)O=1PP[PP
6FUHZ&RQQ+['F1LPP[PP

TML402R
STEP-BY-STEP ASSEMBLY
2#0964-3194
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TML402.10/26/18
channel
channel
HARDWARE / TOOLS INCLUDED
Confirmat Bolt (12)
(Screw Conn HxDc Ni 7mmx50mm)
Hex Wrench
Flat Head Confirmat Bolt (11)
(Screw Conn HxFl ZN 7mmx50mm)
Coat Hook Screw (10)
(Screw Tapp PhOv NI #10x.75)
Coat Hook (9)
(Hook Advtg Coat Dbl Horz Ni)
(Phillips screwdriver required but not included.)
076,QYHQWRU
\
3DUWV/LVW
3DUWV/LVW
3$5747<,7(0
;;
;;
;;
;;
;;
;;
;;
;;




'(6&5,37,21
(QG/
(QG5
7RS%RW
%DFN
6KHOI0LG
6WULQJHU
'LYLGHU6KRUW
'LYLGHU/RQJ
+RRN$GYWJ&RDW'EO+RU]1L
6FUHZ7DSS3K2Y1,[
6FUHZ&RQQ+[)O=1PP[PP
6FUHZ&RQQ+['F1LPP[PP
2-PERSON ASSEMBLY RECOMMENDED.
IMPORTANT!
Be sure to keep all parts supported during assembly to avoid damage.
Do not over-tighten screws or it will damage the pre-drilled holes;
snug fit is adequate.

TML402R
STEP-BY-STEP ASSEMBLY
3
#0964-3194
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TML402.10/26/18
Lay Shelf (5) flat on floor, with side having the
most holes facing down.
STEP
1
Insert dowels on Short Dividers (7) into holes on
Shelf (5), making sure all raw edges are facing the
same direction (will be toward back of unit). Press
firmly into place.
STEP
2
raw edges
raw edge
Align holes on one Top-Bottom (3) with dowels
on Short Dividers (7). Make sure raw edges on
Short Dividers (7) and Shelf (5) are facing toward
routed channel on Top-Bottom (3). Press Top-
Bottom (3) firmly into place.
STEP
3
channel
raw edges
Secure Top-Bottom (3) to Short Dividers (7) with
two Confirmat Bolts (12), using the included Hex
Wrench.
STEP
4
Carefully turn assembly over, so Shelf (5) is facing
up. Secure Shelf (5) to Short Dividers (7) with
two Flat Head Confirmat Bolts (11). This will be
referred to as the Divider Assembly in Step 7.
STEP
5
Lay Left End (1) flat on floor, with side having the
most holes facing up.
STEP
6
Insert dowels on one end of Divider Assembly
from Step 5 into holes on Left End (1). Make sure
raw edges of Divider Assembly are facing flat
(back) edge of Left End (1), and channel on Top-
Bottom (3) is facing toward bottom of unit. Press
firmly into place.
STEP
7
channel
raw edge
Divider
Assembly
flat (back) edge
bottom edge

TML402R
STEP-BY-STEP ASSEMBLY
4#0964-3194
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TML402.10/26/18
Dividers (7 & 8) each have one hole in raw (back)
edge. Back (4) has four holes on back face. These
holes will be used to join Dividers (7 & 8),Back
(4) and Stringers (6) together in Step 18.
STEP
10
Insert dowels on remaining Top-Bottom (3) into
holes on Left End (1). Make sure channel on Top-
Bottom (3) is facing interior of unit and is aligned
with channel on other Top-Bottom (3). Press
firmly into place.
STEP
8
channels
Slide Back (4) into channels on Top-Bottoms (3).
IMPORTANT: Make sure four holes on Back (4)
align with holes on raw (back) edge of Dividers
(7 & 8). Seat Back (4) firmly against Left End (1).
STEP
11
channels
holes must
align when
back is seated
holes must
align when
back is seated
Insert dowels on Stringers (6) into holes on Left
End (1). Make sure holes on face of Stringers (6)
align with holes on Back (4) (reference Step 11).
Press firmly into place.
STEP
12
Beginning with the holes closest to Left End (1),
insert dowels on each Long Divider (8) first into
holes on Top-Bottom (3), then into corresponding
holes on bottom of Shelf (5). To provide enough
room, Top-Bottom (3) can be moved slightly,
but no more than necessary. Make sure all raw
edges are facing same direction (toward back of
unit). Press all parts firmly into place.
STEP
9
raw (back) edges
NOTE:
Movement of
Top-Bottom (3)
is exaggerated
in illustration,
in order to
better depict
Divider (8)
installation.

TML402R
STEP-BY-STEP ASSEMBLY
5
#0964-3194
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TML402.10/26/18
Position Right End (2) on top of assembly, so
dowels on Top-Bottoms (3), Shelf (5) and
Stringers (6) align with holes on Right End (2).
Press firmly into place.
STEP
13
Secure Right End (2) to Top-Bottoms (3), Shelf
(5) and Stringers (6) with eight Confirmat Bolts
(12).
STEP
14
Carefully turn unit over, so Left End (1) is facing
up.
STEP
15
Repeat Step 14 to secure Left End (1) to Top-
Bottoms (3), Shelf (5) and Stringers (6).
STEP
16
Carefully position assembly with back facing up.
STEP
17
Secure Stringers (6), Back (4) and Dividers (7 &
8) together with four Flat Head Confirmat Bolts
(11).
STEP
18

TML402R
STEP-BY-STEP ASSEMBLY
6#0964-3194
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TML402.10/26/18
Ensure that all joints, bolts and screws are tight.
STEP
23
This completes the assembly.
Secure lower Top-Bottom (3) to Long Dividers
(8) with two Confirmat Bolts (12).
STEP
19
Carefully position unit with back flat on floor.
STEP
20
Carefully stand unit upright.
STEP
22
Attach each Coat Hook (9) to underside of Shelf
(5) using two Coat Hook Screws (10) and pre-
drilled holes. (Phillips screwdriver not included.)
STEP
21