Tot Mate TMS302R User manual

1
#0964-3133
3594.TMS302/TM2302/TMS301/TM2304.11/13/18
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.
CAUTION – CHOKING HAZARD
Adult assembly required due to presence
of small parts and sharp edges.
ATTENTION
Please unpack and assemble in an area away from children's activities. Remove all tools
and excess materials from work area after assembly of unit is complete. Dispose of pallet
and packaging materials in an environmentally friendly manner. If any parts are missing
or damaged, please call Stevens for immediate parts replacement (1-800-350-3270).
When ordering parts, give the Model Number and Color of the unit.
by Stevens Industries, Inc.
704 West Main St.
Teutopolis, IL 62467
P: 800.350.3270
P: 217-857-7100 • F: 217-857-7101
www.totmate.com
TMS302R
TM2302R
TMS301R
TM2304R
NOTE: ASSEMBLY INSTRUCTIONS REFERENCE
ILLUSTRATIONS AND PART NUMBERS FOR THE TM2302R.
076,QYHQWRU
\
3DUWV/LVW
3DUWV/LVW
3$5747<,7(0
;;
;;
;;
;;

'(6&5,37,21
7RS%RW
%DFN
6KHOI
(QG8
6FUHZ&RQQ+['F1LPP[PP
TMS302R
Toddler Shelf Storage
076,QYHQWRU
\
3DUWV/LVW
3DUWV/LVW
3$5747<,7(0
;;
;;
;;
;;

'(6&5,37,21
%DFN
7RS%RW
6KHOI
(QG8
6FUHZ&RQQ+['F1LPP[PP
TMS301R
Preschool Shelf Storage
TM2304R
Preschool Shelf Storage
076,QYHQWRU
\
3DUWV/LVW
3DUWV/LVW
3$5747<,7(0
;;
;;
;;
;;


'(6&5,37,21
(QG8
%DFN
6KHOI
7RS
6FUHZ&RQQ+['F1LPP[PP
6FUHZ7DSS3K:K=LQF;
076,QYHQWRU
\
3DUWV/LVW
3DUWV/LVW
3$5747<,7(0
;;
;;
;;
;;


'(6&5,37,21
6KHOI
7RS
(QG8
%DFN
6FUHZ7DSS3K:K=LQF;
6FUHZ&RQQ+['F1LPP[PP
TM2302R
Toddler Shelf Storage

TMS302R – TM2302R – TMS301R – TM2304R
STEP-BY-STEP ASSEMBLY
2#0964-3133
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TMS302/TM2302/TMS301/TM2304.11/13/18
ILLUSTRATIONS AND PART NUMBERS ARE FOR TM2302R.
BASIC ASSEMBLY INSTRUCTIONS ARE THE SAME FOR ALL 4 MODELS.
2-PERSON ASSEMBLY RECOMMENDED.
IMPORTANT!
Be sure to keep all parts supported during assembly to avoid damage.
Do not over-tighten screws or it will damage the pre-drilled holes;
snug fit is adequate.
edgebanding
seam
channel
raw edge
channel
076,QYHQWRU
\
3DUWV/LVW
3DUWV/LVW
TM2302R
3$5747<,7(0
;;
;;
;;
;;


'(6&5,37,21
6KHOI
7RS
(QG8
%DFN
6FUHZ7DSS3K:K=LQF;
6FUHZ&RQQ+['F1LPP[PP
HARDWARE / TOOLS INCLUDED
Confirmat Bolt (6)
(Screw Conn HxDc Ni 7mmx50mm)
Hex Wrench
Back Screw (5)
(Screw Tapp PhWh Zinc #8x1.25)
(Phillips screwdriver required but not included.)

TMS302R – TM2302R – TMS301R – TM2304R
STEP-BY-STEP ASSEMBLY
3
#0964-3133
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TMS302/TM2302/TMS301/TM2304.11/13/18
With End (3) resting on its front edge, insert
dowels on one Top (2) into holes on End (3).
Make sure back edge of Top (2) is facing up and
channel is facing toward interior of unit. Press
firmly into place. Secure Top (2) to End (3) with
two Confirmat Bolts (6).
STEP
2
Repeat Step 2 with other Top (2). Make sure
channel is facing toward interior of unit and
channels on both Tops (2) are aligned.
STEP
3
back edge
channel
channels
Insert dowels on Shelf (1) into remaining holes on
End (3). Make sure raw edge is facing up (toward
back of unit). Press firmly into place. Secure Shelf
(1) to End (3) with Confirmat Bolt (6).
STEP
4
back edge
raw edge
Slide Back (4) into channels on Tops (2). Seat
firmly against End (3). (Note that Backs for
TMS301R/TMS302R do not have any pre-drilled
holes.)
STEP
5
channels
Locate Tops (2) and Ends (3). Note that routed
channels along back edges of Tops (2) will face
interior of unit for installation of Back (4). Also,
note location of edgebanding seam on Ends (3).
IMPORTANT: Edgebanding seams must be
on the bottom of the unit when assembly is
complete.
STEP
1
channels
back edge

TMS302R – TM2302R – TMS301R – TM2304R
STEP-BY-STEP ASSEMBLY
4#0964-3133
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TMS302/TM2302/TMS301/TM2304.11/13/18
Secure End (3) to Tops (2) and Shelf (1) with five
Confirmat Bolts (6).
STEP
7
Secure Back (4) to Shelf (1) with two Back
Screws (5). (Phillips screwdriver not included.)
IMPORTANT! Make sure Back Screws are
centered on edge of Shelf and inserted straight
into Shelf. This is necessary to prevent Back
Screws from protruding through and damaging
Shelf surface. (Note that TMS301R/TMS302R do
not require Back Screws.)
STEP
8
Carefully stand unit upright. Make sure
edgebanding seams on Ends (2) are on bottom of
unit.
STEP
9
Ensure that all joints, bolts and screws are tight.
STEP
10
This completes the assembly.
Position other End (3) at opposite end of unit,
so dowels on Tops (2) and Shelf (1) align with
holes on End (3). Make sure edgebanding seam
is on bottom of unit. Edgebanding seam on both
Ends (3) must be facing same direction. HINT:
Propping up Tops and Shelf will allow End to
be positioned without obstruction.
STEP
6
edgebanding
seam
NOTE: For TMS301R and TMS302R, skip Step 8.