Tot Mate TM2410R User manual

1
#0964-3136
3594.TM2410.9/25/18
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.
CAUTION – CHOKING HAZARD
Adult assembly required due to presence
of small parts and sharp edges.
ATTENTION
Please unpack and assemble in an area away from children's activities. Remove all tools
and excess materials from work area after assembly of unit is complete. Dispose of pallet
and packaging materials in an environmentally friendly manner. If any parts are missing
or damaged, please call Stevens for immediate parts replacement (1-800-350-3270).
When ordering parts, give the Model Number and Color of the unit.
by Stevens Industries, Inc.
704 West Main St.
Teutopolis, IL 62467
P: 800.350.3270
P: 217-857-7100 • F: 217-857-7101
www.totmate.com
TM2410R
2-PERSON ASSEMBLY RECOMMENDED.
IMPORTANT!
Be sure to keep all parts supported
during assembly to avoid damage.
Do not over-tighten screws or it will
damage the pre-drilled holes;
snug fit is adequate.
IMPORTANT!
Assembly must be securely attached to
building structure with anchoring devices
of appropriate type, size and quantity in
accordance with applicable codes and
accepted installation practices.
TM2410R
Wall Cubbie Storage
channel
channel
HARDWARE / TOOLS INCLUDED
Confirmat Bolt (8)
(Screw Conn HxDc Ni 7mmx50mm)
Hex Wrench
Back Screw (12)
(Screw Tapp PhWh Zinc #8x1.25)
Shelf Clip (9)
(Clip Shelf/Divider 1/4"x224mm)
Coat Hook Screw (11)
(Screw Tapp PhOv NI #10x.75)
Coat Hook (10)
(Hook Advtg Coat Dbl Horz Ni)
076,QYHQWRU
\
3DUWV/LVW
Parts List
3$5747<,7(0
;;
;;
;;
;;
;;
;;
;;





'(6&5,37,21
7RS
(QG8
%RWWRP
%DFN
6WULQJHU
'LYLGHU
6XEVKHOI
6FUHZ&RQQ+['F1LPP[PP
&OLS6KHOI'LYLGHU[PP
+RRN$GYWJ&RDW'EO+RU]1L
6FUHZ7DSS3K2Y1,[
6FUHZ7DSS3K:K=LQF;
(Phillips screwdriver required but not included.)

TM2410R
STEP-BY-STEP ASSEMBLY
2#0964-3136
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TM2410.9/25/18
Identify Top (1) and Bottom (3). Note that the
routed channels on Top (1) and Bottom (3) will
face interior of unit and hold Back (4) in place.
To differentiate the parts, note that Bottom (3)
has five sets of small holes on bottom side for
attachment of Coat Hooks (10).
STEP
1
2-PERSON ASSEMBLY RECOMMENDED.
IMPORTANT!
Be sure to keep all parts supported during assembly to avoid damage.
Do not over-tighten screws or it will damage the pre-drilled holes;
snug fit is adequate.
Lay Bottom (3) on floor, with side having the most
holes facing down. Channel will be facing up.
STEP
2
channel
Insert dowels on Dividers (6) into holes on
Bottom (3), making sure all raw edges are facing
toward channel on Bottom (3). Press firmly into
place.
STEP
3
channel
raw edges
Position Top (1) on top of Dividers (6), so dowels
on Dividers (6) align with holes on Top (1). Make
sure channel on Top (1) is aligned with channel on
Bottom (3). Press firmly into place.
STEP
4
channels
channel
channel

TM2410R
STEP-BY-STEP ASSEMBLY
3
#0964-3136
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TM2410.9/25/18
Insert dowels on one end of Divider Assembly
from Step 6 into holes on End (2). Make sure raw
edges and channels on Divider Assembly are
facing toward back (flat) edge of End (2). Press
firmly into place.
STEP
8
Secure Top (1) to two center Dividers (6) with
two Confirmat Bolts (8), using the included Hex
Wrench.
STEP
5
Carefully turn assembly over, so Bottom (3) is
facing up. Repeat Step 5 to secure Bottom (3) to
two center Dividers (6). This will be referred to as
the Divider Assembly in Step 8.
STEP
6
Lay one End (2) flat on floor, with side having the
most holes facing up.
STEP
7
Divider
Assembly
channel
channel
raw edge
back (flat) edge
Slide Back (4) into channels on Top (1) and
Bottom (3). Seat firmly against End (2). When
seated, make sure holes on Back (4) align with
back edges of the two outside Dividers (6).
STEP
9
channel
channel
holes must align
with back edge of
outside Dividers (6)
when Back (4) is
seated

TM2410R
STEP-BY-STEP ASSEMBLY
4#0964-3136
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TM2410.9/25/18
Insert dowels on Stringers (5) into remaining
holes on End (2). Make sure holes on Stringers
(5) align with thru-holes on End (2). Press firmly
into place.
STEP
10
Secure End (2) to Top (1),Bottom (3) and
Stringers (5) with six Confirmat Bolts (8).
STEP
12
thru-holes
Position other End (2) on top of assembly, so
dowels on Top (1),Bottom (3) and Stringers (5)
align with holes on End (2). Press firmly into place.
STEP
11
Carefully turn unit over, so other End (2) is facing
up. Repeat Step 12 to secure End (2) to Top (1),
Bottom (3) and Stringers (5).
STEP
13

TM2410R
STEP-BY-STEP ASSEMBLY
5
#0964-3136
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TM2410.9/25/18
Attach each Coat Hook (10) to underside of
Bottom (3), using two Coat Hook Screws (11)
each and pre-drilled holes.
STEP
17
Carefully position unit with front edge on floor and
back facing up.
STEP
14
Secure Back (4) to the two outside Dividers (6)
with two Back Screws (12). (Phillips screwdriver
not included.) IMPORTANT! Make sure Back
Screws are centered on raw edge of Dividers
and inserted straight into Dividers. This is
necessary to prevent Back Screws from
protruding through and damaging Divider
surfaces.
STEP
15
Carefully lay unit onto its back.
STEP
16
Insert Shelf Clips (9) into holes on each side of
Dividers (6) and inside of each End (2).
STEP
18

TM2410R
STEP-BY-STEP ASSEMBLY
6#0964-3136
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TM2410.9/25/18
Carefully position unit on its top, with coat hooks
facing up.
STEP
20
Ensure that all joints, bolts and screws are tight.
STEP
21
This completes the assembly.
Slide Shelves (7) into Shelf Clips (9), ensuring
rounded edges are facing front of unit.
STEP
19
rounded
edge