Tot Mate TM2206R User manual

channel
channel
edgebanding
seam
1
#0964-3129
3594.TM2206.10/26/18
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.
CAUTION – CHOKING HAZARD
Adult assembly required due to presence
of small parts and sharp edges.
ATTENTION
Please unpack and assemble in an area away from children's activities. Remove all tools
and excess materials from work area after assembly of unit is complete. Dispose of pallet
and packaging materials in an environmentally friendly manner. If any parts are missing
or damaged, please call Stevens for immediate parts replacement (1-800-350-3270).
When ordering parts, give the Model Number and Color of the unit.
by Stevens Industries, Inc.
704 West Main St.
Teutopolis, IL 62467
P: 800.350.3270
P: 217-857-7100 • F: 217-857-7101
www.totmate.com
TM2206R
School Age Compartment Storage
076,QYHQWRU
\
3DUWV/LVW
3DUWV/LVW
3$5747<,7(0
;;
;;
;;
;;
;;
;;


'(6&5,37,21
(QG8
%DFN
'LYLGHU
7RS
6KHOI
'LYLGHU
6FUHZ&RQQ+['F1LPP[PP
6FUHZ7DSS3K:K=LQF;
TM2206R
Confirmat Bolt (7)
(Screw Conn HxDc Ni 7mmx50mm)
Back Screw (8)
(Screw Tapp PhWh Zinc #8x1.25)
Hex Wrench
HARDWARE / TOOLS INCLUDED
(Phillips screwdriver required but not included.)
2-PERSON ASSEMBLY RECOMMENDED.
IMPORTANT!
Be sure to keep all parts supported
during assembly to avoid damage.
Do not over-tighten screws or it will
damage the pre-drilled holes;
snug fit is adequate.

TM2206R
STEP-BY-STEP ASSEMBLY
2#0964-3129
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TM2206.10/26/18
Locate Shelves (5) and note that there is one set
of three holes on one side and two sets of three
holes on the other side. These are for Dividers (3
& 6).
STEP
1
Align dowels on remaining Divider (6) with holes
on Shelf (5). Make sure all raw edges are facing
same direction. Press firmly into place.
STEP
4
Insert dowels on Divider (3) into exposed holes on
bottom of Shelf (5), making sure all raw edges are
flat on floor. Press firmly into place.
STEP
6
Lay one Shelf (5) flat on floor, with side having
the most holes facing up. Insert dowels on two
Dividers (6) into holes on Shelf (5), making sure
raw edges of all parts are facing same direction.
Press firmly into place.
STEP
2
raw edges
raw edge
With side having the most holes facing down, align
holes on other Shelf (5) with dowels on Dividers
(6). Make sure all raw edges are facing same
direction. Press firmly into place.
STEP
3
raw edge
raw edges
raw edges
Carefully position assembly with raw edges flat on
floor. NOTE: Raw edges face back of unit.
STEP
5
raw (back) edges
raw (back) edges

TM2206R
STEP-BY-STEP ASSEMBLY
3
#0964-3129
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TM2206.10/26/18
Lay one End (1) flat on floor, with side having the
most holes facing up.
STEP
12
Secure Dividers (3 & 6) to Shelves (5) with six
Confirmat Bolts (7), using the included Hex
Wrench.
STEP
7
Align holes on one Top (4) with dowels on
exposed Divider (6). Make sure back edge of Top
(4) and all raw (back) edges are facing toward
floor. Press firmly into place.
STEP
8
channel
back
edge
raw (back) edges
Secure Top (4) to Divider (6) with Confirmat Bolt
(7).
STEP
9
Align holes on other Top (4) with dowels on
Divider (3). Make sure channel aligns with
channel on other Top (4). Press firmly into place.
STEP
10
channels
Secure Top (4) to Divider (3) with Confirmat Bolt
(7). This completes the Shelf/Divider Assembly
referenced in Step 13.
STEP
11

TM2206R
STEP-BY-STEP ASSEMBLY
4#0964-3129
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice. 3594.TM2206.10/26/18
Insert dowels on one end of Shelf/Divider
Assembly into holes on one End (1). Press firmly
into place.
STEP
13
Shelf/Divider
Assembly
Slide Back (2) into channels on Tops (4). Seat
firmly against End (1).
STEP
14
channels
Position other End (1) on top of assembly, so
dowels on Tops (4) and Shelves (5) align with
holes on End (1). Press End (1) firmly into place.
STEP
15
Secure End (1) to Tops (4) and Shelves (5) with
six Confirmat Bolts (7).
STEP
16

TM2206R
STEP-BY-STEP ASSEMBLY
5
#0964-3129
©2018 Stevens Industries, Inc.
Due to continuing product development, Stevens reserves the right to change specifications without notice.3594.TM2206.10/26/18
Carefully position unit with front edges on floor and
back facing up.
STEP
19
Secure Back (2) to Shelves (5) with Back
Screws (8). (Phillips screwdriver not included.)
IMPORTANT! Make sure Back Screws are
centered on raw edge of Shelves and inserted
straight into Shelves. This is necessary to
prevent Back Screws from protruding through
and damaging Shelf surface.
STEP
20
Carefully stand unit upright. Make sure
edgebanding seams on Ends (1) are on bottom of
unit.
STEP
21
Ensure that all joints, bolts and screws are tight.
STEP
22
This completes the assembly.
edgebanding
seam
Carefully turn unit over, so other End (1) is facing
up.
STEP
17
Repeat Step 16 to secure End (1) to Tops (4) and
Shelves (5).
STEP
18