Town & Country Fireplaces TC30 Black Diamond User manual

TC30
BLACK DIAMOND
BURNER KIT
INSTRUCTIONS
PART#
TC30.NG03C
For TC30 Series C
080411-20 TC30.NG03C 5056.42903
IMPORTANT:
THESE INSTRUCTIONS ARE TO REMAIN
WITH THE HOMEOWNER
These instructions are supplementary to the Installation
and Operating Instructions supplied with the replace
and should be kept together. Refer to the Installation
and Operating Instructions for proper gas supply, safety
requirements and operating instructions.

TC30.NGO3C 100308-20
2
Contents of Package
AMANIFOLD ASSEMBLY
(including supply tube)
BBURNER TUBE
CBURNER SHIELD
DMEDIA SPACER, Center
EMEDIA SPACER, Front
FMEDIA SPACER, Rear
GHARDWARE PACKAGE
H5 lbs. GLASS MEDIA
IBURNER TRAY
JPILOT SHIELD
(including pilot and pilot supply tube)
NOTE:
MUST BE USED WITH PORCELAIN PANEL SET PART# TC30.PNLPBKB
A
B
C
D
E
F
G
H
I
J

TC30.NGO3C 100308-20
3
A porcelain panel set must be used
in conjunction with the installation of
the burner assembly. See Installation
and Operating Instructions manual for
details.
1. Remove three screws from the rear of
the rebox. Attach the manifold bracket
to the rear of the rebox with the three
screws previously removed. (Fig. #1)
2. Attach the manifold supply tube and the
pilot supply tube to the bulk head ttings
and tighten. (Fig. #2) Ensure that there
are no leaks.
NOTE: If unit is to be converted to Propane,
see Propane conversion instructions on
page 7 before proceeding.
NOTE: Plug the 4 vacant holes in the
bottom of the rebox with 1/2” screws,
as they are not required to attach this
style of burner.
Black Diamond Burner Installation
Fig #1
Fig #2

RED END TO
RED DOT
WHITE END TO
WHITE DOT
MODULE
BULKHEAD PLATE
2 SCREWS
TC30.NGO3C 100308-20
4
3. Secure the electrical bulkhead plate and
gasket to the rebox.(2 screws)Attach the
ignition and sensor wires to the module.
Red end to the connector marked by
the red dot, white end to the connector
marked by the white dot(Fig. #3 & 4)
Fig #3
Fig #4

PILOT
TC30.NGO3C 100308-20
5
4. Install burner shield by tipping the shield
into the rebox. Route pilot up through
the opening in the burner shield.
(Fig. #5)
5. Attach the burner tray to the burner shield
using two screws at the back of the tray.
(Fig. #6)
Fig #5
Fig #6

TC30.NGO3C 100308-20
6
Fig #7
6. Attach pilot shield to burner tray with two
screws. (Fig. #7)
7. Front and rear media spacers are now
installed. (Fig. #8 & 9)
Fig #8

TC30.NGO3C 100308-20
7
8. Install burner by tilting burner inlet through
tray. Ensure that the orice has entered
the inlet tube. (Fig#10).
Set the air shutter to fully open
for Propane or fully closed for
Natural gas.
Fig #9
Fig #10

TC30.NGO3C 100308-20
8
9. Install the center media spacer and secure
to the tray with two 1 1/2” screws.
(Fig. #11 & 12)
Three holes must line up to set each
screw.
Fig #11
Fig #12

TC30.NGO3C 100308-20
9
10. Apply just enough glass media to cover
the burner assembly. (Fig #13 & 14)
NOTE: Too much glass media over the
burner will cause sooting with the use of
propane gas.
Fig #13
Fig #14

TC30.NGO3C 100308-20
10
WARNING
This conversion kit
shall be installed by a
qualied service agency
in accordance with the
manufacturer's instructions
and all applicable codes and
requirements of the authority
having jurisdiction.
If the information in these
instructions is not followed
exactly, a re, explosion
or production of carbon
monoxide may result
causing property damage,
personal injury or loss of
life.
The qualied service agency
is responsible for the proper
installation of this kit. The
installation is not proper and
complete until the operation
of the converted appliance is
checked as specied in the
manufacturer's instructions
supplied with the kit.
If the unit is to be used on propane
convert as follows using the
components supplied with this
replace:
CAUTION
The gas supply and electrical power
shall be shut off before proceeding
with the conversion.
Note:
Factory supplied components must be used
to ensure correct input. After conversion
conrm proper manifold pressure.
1. Ensure the burner, pilot and gas
supply are turned off, and the
appliance has cooled.
2. Using a 1/2”wrench, undo the natural gas
burner orice, (marked #32). (Fig. #15)
3. Apply a small amount of pipe joint com-
pound to the threads of the propane
burner orice (marked #48) to ensure
a good seal, before screwing it into the
tting.
4. Open primary air shutter fully.
5. With a 7/16”wrench loosen the pilot head
on the pilot assembly (Fig. #16)
Fig #15
Fig #16
Propane Conversion
For use with model:
Pour utilise avec du modèle:
LP GAS/
DU GAZ LP
12.5 in/wc /12.5 po/c.e.
(3.11 kPa)
13.9 in/wc / 13.9 po/c.e.
(3.45 kPa)
11.0 in/wc / 11.0 po/c.e.
(.95 kPa)
# 48 (1.93 mm)
Max.: 35,000 (10.3)
Min.: 27,000 (7.91)
080411 6-TC30 5052.52085
Date: ______________________
By / Par: ___________________
This appliance was converted
to PROPANE GAS with this kit
on this date by the organiza-
tion which accepts the respon-
sibility that this conversion
has been properly made. / Cet
appariel etair converter au gaz
LP par l’emploi de la trousse
de conversion par une organi-
zation qui accepte la responsi-
bilité pour une installation en
bon état.
TC30
Series C
MAIN BURNER
(#48) ORIFICES (5021.3407)
MINIMUM RATE SCREW (5005.011)

HOLE
TC30.NGO3C 100308-20
11
Fig #17
Fig #18
6. Slide the pilot adjustment band over and
ensure that the hole in the orice band is
showing.(Fig.#17 indicates NG position,
Fig. #18 indicates LP position)
7. Remove access panel, 10 screws, and
set aside. (Fig. #23)

TC30.NGO3C 100308-20
12
8. Remove the minimum rate screw located
in the valve. (Fig. #19)
9. Replace the minimum rate screw with the
one provided in the propane conversion
kit supplied with this burner. Ensure that
the screw is fully installed. (Fig. #20)
The minimum rate screw is sealed with
an o-ring. Use a thin bladed screwdriver
to back the screw out to the limit of the
threads.
A groove on the screw body will be
visibe just above the valve body.Insert a
thin tool (knife blade or thin screwdriver
blade) into the groove and gently pry
the screw up.
It helps to rotate the screw while
lifting on it.
Fig #19
Fig #20
Minimum
rate screw
Minimum
rate screw

TC30.NGO3C 100308-20
13
NG LP
10) Pull off the aluminum cap from the top
of the pressure regulator. (Fig. #21)
11) Press down on the center post and rotate
90°. The center post should stay down.
(Fig. #22). Replace the aluminum cap.
Fig #21
Fig #22

TC30.NGO3C 100308-20
14
Fig #23
12) Fill in the date and the name of the
person who performed the conversion
in the white area on the conversion
label. Peel off the protective backing and
apply the conversion label directly over
the gas specications on the rating label.
13) Attach the access panel to the side of
the rebox with the previously removed
screws. (Fig. #23)
Note: Gasket must be installed with
access panel.
For use with model:
Pour utilise avec du modèle:
LP GAS/
DU GAZ LP
12.5 in/wc /12.5 po/c.e.
(3.11 kPa)
13.9 in/wc / 13.9 po/c.e.
(3.45 kPa)
11.0 in/wc / 11.0 po/c.e.
(.95 kPa)
# 48 (1.93 mm)
Max.: 35,000 (10.3)
Min.: 27,000 (7.91) 080411 6-TC30 5052.52085
Date: ______________________
By / Par: ___________________
This appliance was converted
to PROPANE GAS with this kit
on this date by the organiza-
tion which accepts the respon-
sibility that this conversion
has been properly made. / Cet
appariel etair converter au gaz
LP par l’emploi de la trousse
de conversion par une organi-
zation qui accepte la responsi-
bilité pour une installation en
bon état.
TC30
Series C

TC30.NGO3C 100308-20
15
1. Remove the plug from the pressure test
port. The plug is located between the
right side lintel and rebox side.
(Fig. #24)
2. Thread the extension test tting into the
open test port. (Fig. #25)
3. Attach a pressure gauge onto the
tting.
4. When testing is complete remove the
extension test tting and replace the plug.
Thread sealant will be required to ensure
a gas tight connection.
Note:To test the gas pressure, turn off the gas supply before removing the plug from
the supply pressure test port or manifold pressure test port.
Verify gas pressures with the replace lit and on the highest setting.
Correct gas pressure requirement:
Supply Pressure Natural Gas Propane
Min. Pressure 5.0" WC 12.5" WC
(For purpose of input adjustment)
Max. Pressure 13.9" WC 13.9" WC
Manifold Pressure
Maximum 3.8" WC 11" WC
Minimum 2.1" WC 5.5" WC
Fig #24
Fig #25
SUPPLY
PRESSURE
MANIFOLD
PRESSURE
Fig #25a
Gas Pressure Check

TC30.NGO3C 100308-20
16
The ame should be just orange
and “lazy”.
It should NEVER be set to create
sooting on internal parts and window
glass.
The air shutter on the burner tube controls the primary combustion air to the gas burner
and is preset at the factory for natural gas fuel. Some adjustment may be necessary to
obtain desired ame and to eliminate carbon deposits. Evaluate ame appearance after
the replace has reached operating temperature. See Fig. #28 for proper ame pattern.
Open primary air shutter if the glass media, glass, and rebox have carbon accumulation
and/or the ames are long, dark and stringy. The shutter may also be opened to lessen
the ame height.
Fig #28
Burner Flame Adjustment

TC30.NGO3C 100308-20
17
ITEM............ DESCRIPTION .................................................................... PART NO.
#1................. TC30 BLACK DIAMOND BURNER KIT ............................ TC30.NG03C2
#2................. BURNER TUBE ...................................................................TC36. 5011835
#3................. PILOT ASSEMBLY, CONVERTIBLE ................................... TCRP.5005025
#4................. PILOT SUPPLY TUBE ......................................................... 5019.225
#5................. ORIFICE, NG (#32).............................................................. 5021.332A
#6................. MANIFOLD SUPPLY TUBE................................................. 5019.223
#7................. GLASS MEDIA ................................................................... 5012.01
#8................. PROPANE CONVERSION KIT............................................ TC30.LPCE01
#1.....TC30 BLACK DIAMOND BURNER KIT
1a
MEDIA SPACER, REAR
1b MEDIA SPACER, CENTER
1c MEDIA SPACER, FRONT
1d BURNER TRAY
1e BURNER SHIELD
1f PILOT SHIELD
1g MANIFOLD ASSEMBLY
1h MANIFOLD BRACKET
1i SHIELD LEG
2 BURNER TUBE
3 PILOT ASSEMBLY, CONVERTIBLE
4 PILOT SUPPLY TUBE
5 ORIFICE
6 MANIFOLD SUPPLY TUBE
7 GLASS MEDIA
8 PROPANE CONVERSION KIT
...(Not shown)
#2.....BURNER TUBE
#3.....PILOT ASSEMBLY, CONVERTIBLE
#4.....PILOT SUPPLY TUBE
#5.....ORIFICE, NG (#32)
#6 MANIFOLD SUPPLY TUBE
#7.....GLASS MEDIA
#8.....PROPANE CONVERSION KIT
...(Not Shown)
KIT CONTENTS:
(WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION)
*
*NOT SHOWN
#1
#2
#3
#5
#4
1d
1a
1b
1c
1e 1f
1h
1i
1g
#6
#7
Replacement Parts

TC30.NGO3C 100308-20
18

TC30.NGO3C 100308-20
19

Technical support: 1-250-748-1184
Web site: www.townandcountryreplaces.net
2975 Allenby Rd., Duncan, BC V9L 6V8
Printed in Canada