Town & Country Fireplaces TC42 User manual

Visit www. townandcountryfireplaces.com for the most recent version of this manual
150223-16 SKU# 22150038 100000363-50
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
These instructions are supplementary to the Installation and
Operating Instructions supplied with the replace and should be
kept together. Refer to the Installation and Operating Instructions for
proper gas supply, safety requirements and operating instructions
TC42
HEARTWOOD
BURNER KIT
INSTALLATION
INSTRUCTIONS
SKU#22150038
For TC42 Series D
Fireplaces

100000363-50 2SKU# 22150038_150223-16
Contents of Package
• Burner assembly
(including pilot and manifold)
• Log grate
• TC42 Heartwood logs
• Ember pieces (one bag)
• Coal chunks (one bag)
• Ember wool (one bag)
• Hardware package
Burner Installation
1. Place the keyhole slots in the burner (Figure 2) over the two screws located in the rebox base (Figure 3).
2. Slide the burner back to engage the screws in the small part of the keyhole slot and tighten screws.
3. Remove access cover from side of rebox (Figure 4).
If this fireplace is to be
used on Propane please
convert prior to installtion.
See pages 10 - 12.
Figure 1: Heartwood package contents.
Figure 2: Attaching burner to oor of
replace.
Bolts
Figure 3: Bolts for burner.
Figure 4:
Control center
access cover.

3
SKU#22150038_150223-16 100000363-50
2 SCREWS
Burner/ Grate Installation
4. Attach the manifold gas and
pilot supply tubes to the bulk
head tting and tighten
(Figure 5).
Ensure that all connections are
gas tight.
5. Feed the ignition and sensor
wires through the bulkhead
plate (Figure 6) to the interface.
Figure 5: Gas and pilot supply tubes.
Ignition and sensor wires
Bulkhead plate
Figure 6: Ignition and sensor wires routing.

100000363-50 4SKU# 22150038_150223-16
6. Attach the ignition and sensor
wires to the module (Figure 7).
7. Replace the access cover.
8. Position the slots of the grate
securing brackets over the
holes in the oor shield and
secure with the two screws
(Figure 8).
Ignition wire (red)
Flame sensor
wire (white)
Interface module
Figure 7: Interface module.
Figure 8: Securing the grate.
A panel set must now be installed.
See Installation and Operating
Instructions manual for details.

5
SKU#22150038_150223-16 100000363-50
Ember Material
A large bag of ember wool is
supplied with the Heartwood
burner kit and needs to be
installed on the burner to ensure
optimum performance and ame
appearance. A bag of large coal
chunks and small ember pieces
are also supplied. These must
only be used around the burner
pan to cover up the gas lines and
brackets.
1. Pull apart the ember wool into
ember size pieces (approxi-
mately 1” squares) and gently
place them into the burner pan.
Do not compress, leave them
loose for best performance.
2. Fill the burner pan level with
the top of the pan at rear, and
gradually sloping forward down
to the rebox oor at the front,
covering both burner tubes
(Figure 9).
3. Place remaining ember
material, coal chunks and
small ember material outside
of the burner pan as desired
to cover-up gas lines and
brackets. (Figure 10). Do not
put coal chunks or small
ember pieces inside burner
pan as this will cause
sooting and the burner to
malfunction.
Note: Ember material placement and amount will affect
flame appearance.
More ember material results in lower flame height.
Add or remove as needed until desired flame affect.
Reduce the amount used on Propane models, as too
much will create soot
Ember wool in this area only
Figure 9: Placement of ember wool on the burner pan.
Ember wool, coal
chunks and ember
pieces
Figure 10: Full distribution of ember, coal chunks and ember pieces.ai

100000363-50 6SKU# 22150038_150223-16
Log Set Assembly
Gas plumbing and vent connections
should be completed before
proceeding.
The logs are fragile, and should be
handled with care. Unpack and inspect
log set. There should be a total of
seven logs.
Position the logs as indicated by the
following pictures. The seven main logs
have holes and / or pins. Engage each
pin in the corresponding holes. The
remaining two logs do not have holes
or pins. They rest in position. Locate
as per the diagrams (Figures 11-19)
Note: Improper placement of logs
will cause sooting on internal parts
and glass. The logs may need to
be repositioned slightly to avoid
excessive flame impingement.
Figure 11: Log 1 placement.
Figure 12: Log 2 placement.

7
SKU#22150038_150223-16 100000363-50
Figure 13: Log 3 placement.
Figure 14: Log 4 placement.

100000363-50 8SKU# 22150038_150223-16
Figure 15: Log 5 placement.
Figure 16: Log 6 placement.

9
SKU#22150038_150223-16 100000363-50
Figure 17: Log 7 placement.
Figure 18: Log 8 placement.
Figure 19: Log 9 placement.

100000363-50 10 SKU# 22150038_150223-16
Propane Conversion
If the unit is to be used with propane gas, convert the fireplace from natural gas as follows using the
components supplied with this burner kit.
Note: Factory supplied components must be used to ensure correct input. After conversion conrm proper
manifold pressure.
CAUTION
The gas supply and electrical power must be shut off before proceeding with the conversion.
WARNING
is conversion kit shall be installed by a qualied service agency in accordance with the manufacturer's instructions
and all applicable codes and requirements of the authority having
jurisdiction.
If the information in these instructions is not followed exactly, a re, explosion or production of carbon monoxide
may result causing property damage, personal injury or loss of life.
e qualied service agency is responsible for the proper installation of this kit.
e installation is not proper and complete until the operation of the converted appliance is checked as specied in
the manufacturer's instructions supplied with the kit.
1. Ensure the burner, pilot and gas supply are turned off, and the appliance has cooled.
2. Remove the two screws securing the manifold assembly to the burner (Figure 20).
3. Remove the manifold assembly from the burner (Figure 21).
Figure 20: Unscrewing manifold from the burner. Figure 21: Orice exposed.
Note: e propane conversion kit is not included with the burner kit. e conversion
kit is an option which must be ordered separately.

11
SKU#22150038_150223-16 100000363-50
4. With a ½” wrench remove the natural gas orice (Figure 22).
5. Install the propane orice (marked “LE”) (Figure 23).
6. Fully open the primary air shutter.
Figure 22: Removing orice. Figure 23: Orice.
Figure 24: Loosening the pilot head.
7. Reinstall the manifold assembly.
8. With a 7/16” wrench loosen the pilot head on the pilot assembly by a half-turn (Figure 24)
9. Slide the pilot adjustment band over and ensure that the hole in the orice band is showing. Figure 25
shows the pilot band in natural gas position. Figure 26 shows the pilot band in propane position.

100000363-50 12 SKU# 22150038_150223-16
For complete valve installation instructions, refer to the
instruction book included in the SIT conversion kit.
10. Open the air shutter by following the steps in the “Burner Flame Adjustment” on page 13.
11. Complete the gas valve conversion from natural gas to propane gas according to the instructions included
in the SIT propane gas conversion kit.
12. Fill in the conversion label (Figure 27) . Peel off the protective backing and apply the conversion label
directly over the gas specications on the rating label. Rating label can be found on a metal plate stored
on the left hand side of the replace, behind the decorative trim.
Pilot
adjustment
band
Figure 25: Pilot band in natural gas position.
Hole in sliding band
indicates propane
gas conguration
Figure 26: Pilot band in propane gas position.
Cet appareil a été converti en gaz propane
Numéro d'assemblage
j m a
Firme
Adresse
l'entreprise désignée
ci-dessus accepte la
responsabilité que cette
conversion a été
correctement faite.
Kit Number
dd mm yy
Company
Address
The above accepts the
responsibility that this
conversion has been
properly performed.
This appliance was converted to propane gas
5052.52001-B
5052.52001-B
Figure 27: Propane conversion label.

13
SKU#22150038_150223-16 100000363-50
The air shutter on the burner tube controls the primary combustion air to the gas burner and is preset at the
factory for natural gas fuel. Some adjustment may be necessary to obtain desired ame and to eliminate
carbon deposits. Evaluate ame appearance after the replace has reached operating temperature.
Open primary air shutter if the logs, glass, and rebox have carbon accumulation and / or the ames are long,
dark and stringy. The shutter may also be opened to enhance the Ember Material glow and lessen the ame
height. See Figure 28 for an example of a proper looking ame. The ame should be just orange and “lazy”. It
should NEVER be set to create sooting on internal parts and glass.
Caution: Burner area may be hot! Turn off the replace and allow the unit to cool before proceeding.
Burner Flame Adjustment
To Adjust:
1. Open and remove window frame and set aside. See "Window Frame Removal" section found in the
Installation and Operating Instructions manual.
2. Remove the log set and set aside.
3. Locate and loosen the air shutter adjustment screw (Figure 31).
4. Rotate the shutter to increase or decrease the air intake depending on type of gas being used.
5. Tighten adjustment screw and reassemble in log set.
Figure 28: Desirable ame appearance Figure 29: Air shutter location.
1/8” gap
Figure 30: Air shutter in natural gas position.
Air shutter
adjustment
screw
Air shutter
opening
Figure 31: Shutter set for propane.

100000363-50 14 SKU# 22150038_150223-16
Replacement Parts
#1........ BURNER ASSEMBLY ....................................... 22150038
#2........ 9 PCS LOG SET................................................ 80001228
#3........ ORIFICE, NATURAL GAS (#20)......................5022.78-00
#4........ PILOT ASSEMBLY............................................ 80000522
KIT CONTENTS:
(WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION)
ITEM DESCRIPTION PART NO.
#5........ MAIN SUPPLY TUBE (FLEX)........................5019.223-00
#6........ PILOT TUBE (FLEX) ....................................5019.225-00
#7........ PROPANE CONVERSION KIT ...................... 22180008 *
ITEM DESCRIPTION PART NO.
1
2
3
4
7
5
6
8
9
#2 #3
#4
#6
#5
#1
1a
1b
1e
1d
1f
1h
1c 1g
#1........ BURNER ASSEMBLY
1a........GRATE
1b........BURNER INSULATION
1c........BURNER TRAY SUPPORT SHIELD
1d........PILOT SHIELD
1e........TC42.NG01 BURNER WELD
1f.........MANIFOLD
1g........1/2 PIPE TO 1/2 TUBE CONNECTION
1h........PILOT BRACKET
#2........ 9 PCS LOG SET
EMBER MATERIAL (Not shown)
#3........ ORIFICE, NATURAL GAS (#20)
#4........ PILOT ASSEMBLY, CONVERTIBLE
#5........ MAIN SUPPLY TUBE (FLEX)
#6........ PILOT TUBE (FLEX)

15
SKU#22150038_150223-16 100000363-50

For technical support, please contact your retailer.
www.townandcountryfireplaces.net
2975 Allenby Rd., Duncan, BC V9L 6V8
Printed in Canada
© 2016 Copyright Pacic Energy Fireplace Products LTD
Reproduction, adaptation, or translation
without prior written permission is prohibited,
except as allowed under the copyright laws.