Toyota Fortuner UH9000S User manual

UHF CB Transceiver
UH9000S / UH9060S / UH9080S
Fitting Instructions
Land Cruiser Prado
Fitting Kit Part Number: UNIFK002

Page 2 of 16
Fitting Instructions
UH9000S / UH9060S / UH9080S
UHF CB Transceiver
Front
Antenna
Connector
Speaker
Microphone
UH9000S
Rear
Earth
A
ccessory
Power
+
Fuse
Power
Lead Patch
Harness
Antenna
Connector
Extension
Cable
(Optional)
UH9060S / UH9080S
Earth
A
ccessory
Power
+
Fuse
Remote LCD
Speaker
Microphone
Rear
UHF CB Transceiver
Front
Power
Lead Patch
Harness

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 3 of 16
WARNING
This vehicle is equipped with Supplemental Restraint System (SRS) airbags and seatbelt pretensioners.
Before starting work, wait at least 90 seconds after the ignition switch is turned off and the negative (-) battery terminal
cable is disconnected.
SRS parts are equipped with a backup power source. If work is started within 90 seconds of turning the ignition switch off
and disconnecting the negative (-) battery terminal cable, SRS parts may deploy possibly causing serious injuries.
WARNING
Do not install any parts in a location that may interfere with the operation and deployment of the SRS airbags or seatbelt
pretensioners, including driver, front passenger and knee SRS airbags if tted. Doing so may result in serious injury or
death.
PREPARATION
• Follow all standard workshop and occupational health and safety practices during the installation process.
• Check and note any existing marks or damage to the vehicle.
• Before starting the installation thoroughly read through these installation instructions then follow the tting sequence as described.
• Check that the UHF CB transceiver kit is complete.
• Take all possible precautions to avoid damaging the vehicle’s interior and exterior during the installation. Use protective tape on
parts and tools where necessary.
• To avoid damage to the wiring harness and antenna cable, avoid contact with sharp edges. Cable tie securely every 200 mm.
• Ensure all removed parts are re-tted correctly.
SPECIAL TOOLS
• Trim removal tool
• Protective tape
• Lead wire
PARTS LIST - UHF CB TRANSCEIVER KITS
Model UHF CB Transceiver Kit Fitting Kit Part Number
PRADO 150
UH9000S
UNIFK002UH9060S
UH9080S
PARTS LIST - ANTENNA
Model Antenna Part Number Description
PRADO 150
AT970BKTWIN Antenna Dual Whip Black
AT970WTWIN Antenna Dual Whip White
AT970BK Antenna 1200mm Black
AT970W Antenna 1200mm White
AT890BK Antenna 1000mm Black
AT890W Antenna 1000mm White
AT880TWIN Antenna Dual Whip Stainless Steel

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 4 of 16
REMOVAL
Removal - Engine Bay
1. Open the bonnet.
2. Remove the radiator shroud (13 scrivets).
Push in the centre of the scrivets and pull up the shroud to
remove. Take care to retain all scrivets.
3. Disconnect the (-) negative battery terminal cable.
4. Disconnect the positive (+) terminal cable.
5. Remove the battery retaining bracket and hook.
6. Remove the battery and store safely.
7. Use a at blade screwdriver to unclip (2) the relay box
located at the passenger’s side rewall. Lower the fuse
box to gain access to the rewall grommet.

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 5 of 16
8. Cut the outer tang off the rewall grommet where
indicated.
Note: Refer to the Alternate antenna cable entry point
on page 9 if both grommet entry points are being
used..
Removal - Interior
1. Using a taped at blade screwdriver remove the front
passenger’s side scuff plate (4 clips [ ], 10 claws and 2
guides).
Prise off carefully at retaining clip locations to avoid
damaging the clips and plate.
2. Remove the front passenger’s cowl side trim board
(1 push-in clip and 2 clips [ ])
Prise off carefully at retaining clip locations to avoid
damaging the clips and panel.
3. Remove the front passenger’s side instrument panel under
cover sub-assembly.
Remove (1) screw, unclip (3 [ ]), lower and pull away from
rewall.

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 6 of 16
4. Remove the passenger’s side front console box insert
(2 clips [ ], 1 guide).
Prise off carefully at retaining clip locations to avoid
damaging the clips and insert.
5. Remove the driver’s side front console box insert
(2 clips [ ], 1 guide).
Prise off carefully at retaining clip locations to avoid
damaging the clips and insert.
6. Place protective tape along both sides of the centre
console. Using a trim removal tool carefully prise down
from the top of the rear console end panel sub-assembly to
unclip and expose the rear power socket wiring
(4 clips [ ]).

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 7 of 16
INSTALLATION
Antenna
1. Remove the sleeve, spacer washer, lock washer and nut
from the antenna.
2. Pass the antenna cable through the antenna mounting
hole.
3. Secure the antenna to the mount using the sleeve, spacer
washer, lock washer and nut. Tighten securely.
Antenna Cable
1. Pass the antenna cable through the radiator grille opening
in the location as shown.
2. Route the cable through the radiator support panel
opening as shown.

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 8 of 16
3. Follow the existing wiring harness passing the antenna
cable through the (2) existing wiring harness clips.
4. At the completion of the installation, cable tie the antenna
harness to the existing wiring harness where indicated [ ].
5. Route the antenna cable between the fuse and relay
box and the inner quarter panel, through the existing clip
and below the fuel lter assembly (if tted) and mounting
bracket.
6. At the completion of the installation, cable tie the antenna
cable to the existing wiring harness where indicated [ ].
7. Follow the existing wiring harness to the rewall grommet.
8. At the completion of the installation, cable tie the antenna
cable to the existing wiring harness where indicated [ ].
9. Pass a lead wire through the cut rewall grommet opening
to the passenger’s side footwell.
Attach the antenna cable to the lead wire.

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 9 of 16
Alternate antenna cable entry point
9. Remove the grommet from the rewall:
a. Drill a 5 mm hole through the centre.
b. Ret the grommet to the rewall opening.
c. Pass a lead wire through the cut rewall grommet
opening to the passenger’s side footwell.
d. Attach the antenna cable to the lead wire.
10. Carefully pull the lead wire and antenna cable through
from the passenger’s side footwell.
IMPORTANT
Use silicon spray to allow the antenna cable to pass
through the grommet more easily.
11. At the completion of the installation process seal the
antenna cable grommet entry point with an automotive
grade sealant and secure with a cable tie.
UH9000S
12. Disconnect the lead wire and route the antenna cable
below the footwell carpet line, behind the centre console
towards the driver’s side footwell.
13. Pull the antenna cable through to the driver’s footwell.

Fitting Instructions
UH9000S / UH9060S / UH9080S
Page 10 of 16
UH9060S / 9080S
14. Disconnect the lead wire and pull the antenna cable into
the passenger’s side footwell.
Power Lead Patch Harness - UH9000S
1. Route the power lead patch harness from the driver’s side
footwell, behind the bottom edge of the console box
assembly to the rear power socket connector.
2. Disconnect the rear power socket connector and dehouse
the (2) connector pins from the rear power socket
connector [1].
3. House the (2) removed pins in the free power lead patch
harness connector [2].
4. House the (2) free power lead patch harness pins into the
existing rear power socket connector [3].
5. Connect the existing rear power socket connector to the
rear power socket [4].
IMPORTANT
6. Refer to the following diagram for wiring details
PRADO
1
Power
socket
Existing vehicle
harness
Existing vehicle power
socket connector
Existing vehicle power
socket connector Power
socket
4
To UHF CB
transceiver
Power lead
patch harness
Existing vehicle power
socket connector
To UHF CB
transceiver
3
Existing vehicle
harness Power lead
patch harness
2
Existing vehicle
harness Power lead
patch harness To UHF CB
transceiver
1
2
1
2
1
2