TP-Link Tapo T110 User manual

Images may dier from actual products.
Smart Contact Sensor
Quick Start Guide
Before You Start
A Tapo Hub is required. Make sure your Tapo
Hub is successfully added via the Tapo app.
OR
Remove the battery insulation tab to power up
your sensor. The LED should begin to blink.
Note: If the LED is not blinking, refer to the reverse side for
reset instructions.
Meet Your Contact Sensor
Know when doors/windows are opened or closed. Receive instant alerts via the Tapo app. Open the Tapo app, tap the button in the
app, and select your model. Follow the app
instructions to complete setup.
a. Open and close the sensor to test it in
your preferred location.
b. Check the Event Log on the Tapo app to
conrm the open/closed status.
1. Power Up Your Sensor 2. Set Up Your Sensor 3. Test Your Sensor12 3
7106509753 REV1.1.1
Setup Video
Scan QR code or visit
https://www.tp-link.com/support/
setup-video/#smart-sensors
LED Light
Sensor
Magnet
Magnet
Alignment
Mark Battery
Compartment
Reset Button

Images may dier from actual products.
Smart Contact Sensor
Quick Start Guide
Before You Start
A Tapo Hub is required. Make sure your Tapo
Hub is successfully added via the Tapo app.
OR
Remove the battery insulation tab to power up
your sensor. The LED should begin to blink.
Note: If the LED is not blinking, refer to the reverse side for
reset instructions.
Meet Your Contact Sensor
Know when doors/windows are opened or closed. Receive instant alerts via the Tapo app. Open the Tapo app, tap the button in the
app, and select your model. Follow the app
instructions to complete setup.
a. Open and close the sensor to test it in
your preferred location.
b. Check the Event Log on the Tapo app to
conrm the open/closed status.
1. Power Up Your Sensor 2. Set Up Your Sensor 3. Test Your Sensor12 3
7106509753 REV1.1.1
Setup Video
Scan QR code or visit
https://www.tp-link.com/support/
setup-video/#smart-sensors
LED Light
Sensor
Magnet
Magnet
Alignment
Mark Battery
Compartment
Reset Button

Images may dier from actual products.
Smart Contact Sensor
Quick Start Guide
Before You Start
A Tapo Hub is required. Make sure your Tapo
Hub is successfully added via the Tapo app.
OR
Remove the battery insulation tab to power up
your sensor. The LED should begin to blink.
Note: If the LED is not blinking, refer to the reverse side for
reset instructions.
Meet Your Contact Sensor
Know when doors/windows are opened or closed. Receive instant alerts via the Tapo app. Open the Tapo app, tap the button in the
app, and select your model. Follow the app
instructions to complete setup.
a. Open and close the sensor to test it in
your preferred location.
b. Check the Event Log on the Tapo app to
conrm the open/closed status.
1. Power Up Your Sensor 2. Set Up Your Sensor 3. Test Your Sensor12 3
7106509753 REV1.1.1
Setup Video
Scan QR code or visit
https://www.tp-link.com/support/
setup-video/#smart-sensors
LED Light
Sensor
Magnet
Magnet
Alignment
Mark Battery
Compartment
Reset Button

Images may dier from actual products.
Smart Contact Sensor
Quick Start Guide
Before You Start
A Tapo Hub is required. Make sure your Tapo
Hub is successfully added via the Tapo app.
OR
Remove the battery insulation tab to power up
your sensor. The LED should begin to blink.
Note: If the LED is not blinking, refer to the reverse side for
reset instructions.
Meet Your Contact Sensor
Know when doors/windows are opened or closed. Receive instant alerts via the Tapo app. Open the Tapo app, tap the button in the
app, and select your model. Follow the app
instructions to complete setup.
a. Open and close the sensor to test it in
your preferred location.
b. Check the Event Log on the Tapo app to
conrm the open/closed status.
1. Power Up Your Sensor 2. Set Up Your Sensor 3. Test Your Sensor12 3
7106509753 REV1.1.1
Setup Video
Scan QR code or visit
https://www.tp-link.com/support/
setup-video/#smart-sensors
LED Light
Sensor
Magnet
Magnet
Alignment
Mark Battery
Compartment
Reset Button

Images may dier from actual products.
Smart Contact Sensor
Quick Start Guide
Before You Start
A Tapo Hub is required. Make sure your Tapo
Hub is successfully added via the Tapo app.
OR
Remove the battery insulation tab to power up
your sensor. The LED should begin to blink.
Note: If the LED is not blinking, refer to the reverse side for
reset instructions.
Meet Your Contact Sensor
Know when doors/windows are opened or closed. Receive instant alerts via the Tapo app. Open the Tapo app, tap the button in the
app, and select your model. Follow the app
instructions to complete setup.
a. Open and close the sensor to test it in
your preferred location.
b. Check the Event Log on the Tapo app to
conrm the open/closed status.
1. Power Up Your Sensor 2. Set Up Your Sensor 3. Test Your Sensor12 3
7106509753 REV1.1.1
Setup Video
Scan QR code or visit
https://www.tp-link.com/support/
setup-video/#smart-sensors
LED Light
Sensor
Magnet
Magnet
Alignment
Mark Battery
Compartment
Reset Button

Images may dier from actual products.
Smart Contact Sensor
Quick Start Guide
Before You Start
A Tapo Hub is required. Make sure your Tapo
Hub is successfully added via the Tapo app.
OR
Remove the battery insulation tab to power up
your sensor. The LED should begin to blink.
Note: If the LED is not blinking, refer to the reverse side for
reset instructions.
Meet Your Contact Sensor
Know when doors/windows are opened or closed. Receive instant alerts via the Tapo app. Open the Tapo app, tap the button in the
app, and select your model. Follow the app
instructions to complete setup.
a. Open and close the sensor to test it in
your preferred location.
b. Check the Event Log on the Tapo app to
conrm the open/closed status.
1. Power Up Your Sensor 2. Set Up Your Sensor 3. Test Your Sensor12 3
7106509753 REV1.1.1
Setup Video
Scan QR code or visit
https://www.tp-link.com/support/
setup-video/#smart-sensors
LED Light
Sensor
Magnet
Magnet
Alignment
Mark Battery
Compartment
Reset Button

Support
For technical support, the user guide and more,
please visit https://www.tapo.com/support/
c. Align the magnet and sensor with no more
than 0.59 inches (15 mm) between them
when the door or window is closed.
Peel the backing from the adhesive and
press the sensor and magnet into place.
b. Choose where you’d like to install the sensor
(but don’t attach it yet). Place the magnet
near the edge of the door or window that
moves.
Notes:
· Leave at least 0.39 inches (10 mm) of space so you can open the
battery compartment.
· Installation height should not be higher than 6.56 ft (2 m).
OPEN
a. Slide to remove the cover of your sensor.
b. Use a pin to press and hold the Reset button
for 5 seconds until the front LED starts
blinking.
If you have mounted your sensor to a door
or a window, remove the cover as shown
below:
How to reset your sensor to enter pairing mode
a. Remove the cover of your sensor and use a
screwdriver to open the battery cover.
b. Replace the battery with a fresh cell.
How to replace the battery
5s
a. Stick the included adhesives on the
sensor and magnet.
x2
x1
4. Mount Your Sensor
4
0cm 1 2
≤ 0.59 inches (15 mm)
Alignment
Lines
≥ 0.39 inches (10 mm)
OPEN
©2022 TP-Link
Do not ingest battery, Chemical Burn Hazard
This product contains a coin / button cell battery. If the coin / button cell
battery is swallowed, it can cause severe internal burns in just 2 hours and can
lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product
and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
Do not use the device where wireless devices are not allowed.
Please read and follow the above safety information when operating the
device. We cannot guarantee that no accidents or damage will occur due to
improper use of the device. Please use this product with care and operate at
your own risk.
CAUTION!
Avoid replacement of a battery with an incorrect type that can defeat a
safeguard.
Avoid disposal of a battery into re or a hot oven, or mechanically crushing or
cutting of a battery, that can result in an explosion.
Do not leave a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of ammable liquid
or gas; Do not leave a battery subjected to extremely low air pressure that may
result in an explosion or the leakage of ammable liquid or gas.
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/53/EU,
2009/125/EC, 2011/65/EU and (EU) 2015/863.
The original EU declaration of conformity may be
found at https://www.tapo.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Radio Equipment
Regulations 2017.
The original UK declaration of conformity may be found at
https://www.tapo.com/support/ukca/
For EU/UK Region:
Operating Frequency / Nominal Operating Frequency / Max Output Power:
863~865MHz / 863.35MHz / 25mW (e.r.p)
863~865MHz / 864.35MHz / 25mW (e.r.p)
868~868.6MHz / 868.35MHz / 25mW (e.r.p)

Support
For technical support, the user guide and more,
please visit https://www.tapo.com/support/
c. Align the magnet and sensor with no more
than 0.59 inches (15 mm) between them
when the door or window is closed.
Peel the backing from the adhesive and
press the sensor and magnet into place.
b. Choose where you’d like to install the sensor
(but don’t attach it yet). Place the magnet
near the edge of the door or window that
moves.
Notes:
· Leave at least 0.39 inches (10 mm) of space so you can open the
battery compartment.
· Installation height should not be higher than 6.56 ft (2 m).
OPEN
a. Slide to remove the cover of your sensor.
b. Use a pin to press and hold the Reset button
for 5 seconds until the front LED starts
blinking.
If you have mounted your sensor to a door
or a window, remove the cover as shown
below:
How to reset your sensor to enter pairing mode
a. Remove the cover of your sensor and use a
screwdriver to open the battery cover.
b. Replace the battery with a fresh cell.
How to replace the battery
5s
a. Stick the included adhesives on the
sensor and magnet.
x2
x1
4. Mount Your Sensor
4
0cm 1 2
≤ 0.59 inches (15 mm)
Alignment
Lines
≥ 0.39 inches (10 mm)
OPEN
©2022 TP-Link
Do not ingest battery, Chemical Burn Hazard
This product contains a coin / button cell battery. If the coin / button cell
battery is swallowed, it can cause severe internal burns in just 2 hours and can
lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product
and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
Do not use the device where wireless devices are not allowed.
Please read and follow the above safety information when operating the
device. We cannot guarantee that no accidents or damage will occur due to
improper use of the device. Please use this product with care and operate at
your own risk.
CAUTION!
Avoid replacement of a battery with an incorrect type that can defeat a
safeguard.
Avoid disposal of a battery into re or a hot oven, or mechanically crushing or
cutting of a battery, that can result in an explosion.
Do not leave a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of ammable liquid
or gas; Do not leave a battery subjected to extremely low air pressure that may
result in an explosion or the leakage of ammable liquid or gas.
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/53/EU,
2009/125/EC, 2011/65/EU and (EU) 2015/863.
The original EU declaration of conformity may be
found at https://www.tapo.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Radio Equipment
Regulations 2017.
The original UK declaration of conformity may be found at
https://www.tapo.com/support/ukca/
For EU/UK Region:
Operating Frequency / Nominal Operating Frequency / Max Output Power:
863~865MHz / 863.35MHz / 25mW (e.r.p)
863~865MHz / 864.35MHz / 25mW (e.r.p)
868~868.6MHz / 868.35MHz / 25mW (e.r.p)

Support
For technical support, the user guide and more,
please visit https://www.tapo.com/support/
c. Align the magnet and sensor with no more
than 0.59 inches (15 mm) between them
when the door or window is closed.
Peel the backing from the adhesive and
press the sensor and magnet into place.
b. Choose where you’d like to install the sensor
(but don’t attach it yet). Place the magnet
near the edge of the door or window that
moves.
Notes:
· Leave at least 0.39 inches (10 mm) of space so you can open the
battery compartment.
· Installation height should not be higher than 6.56 ft (2 m).
OPEN
a. Slide to remove the cover of your sensor.
b. Use a pin to press and hold the Reset button
for 5 seconds until the front LED starts
blinking.
If you have mounted your sensor to a door
or a window, remove the cover as shown
below:
How to reset your sensor to enter pairing mode
a. Remove the cover of your sensor and use a
screwdriver to open the battery cover.
b. Replace the battery with a fresh cell.
How to replace the battery
5s
a. Stick the included adhesives on the
sensor and magnet.
x2
x1
4. Mount Your Sensor
4
0cm 1 2
≤ 0.59 inches (15 mm)
Alignment
Lines
≥ 0.39 inches (10 mm)
OPEN
©2022 TP-Link
Do not ingest battery, Chemical Burn Hazard
This product contains a coin / button cell battery. If the coin / button cell
battery is swallowed, it can cause severe internal burns in just 2 hours and can
lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product
and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
Do not use the device where wireless devices are not allowed.
Please read and follow the above safety information when operating the
device. We cannot guarantee that no accidents or damage will occur due to
improper use of the device. Please use this product with care and operate at
your own risk.
CAUTION!
Avoid replacement of a battery with an incorrect type that can defeat a
safeguard.
Avoid disposal of a battery into re or a hot oven, or mechanically crushing or
cutting of a battery, that can result in an explosion.
Do not leave a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of ammable liquid
or gas; Do not leave a battery subjected to extremely low air pressure that may
result in an explosion or the leakage of ammable liquid or gas.
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/53/EU,
2009/125/EC, 2011/65/EU and (EU) 2015/863.
The original EU declaration of conformity may be
found at https://www.tapo.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Radio Equipment
Regulations 2017.
The original UK declaration of conformity may be found at
https://www.tapo.com/support/ukca/
For EU/UK Region:
Operating Frequency / Nominal Operating Frequency / Max Output Power:
863~865MHz / 863.35MHz / 25mW (e.r.p)
863~865MHz / 864.35MHz / 25mW (e.r.p)
868~868.6MHz / 868.35MHz / 25mW (e.r.p)

Support
For technical support, the user guide and more,
please visit https://www.tapo.com/support/
c. Align the magnet and sensor with no more
than 0.59 inches (15 mm) between them
when the door or window is closed.
Peel the backing from the adhesive and
press the sensor and magnet into place.
b. Choose where you’d like to install the sensor
(but don’t attach it yet). Place the magnet
near the edge of the door or window that
moves.
Notes:
· Leave at least 0.39 inches (10 mm) of space so you can open the
battery compartment.
· Installation height should not be higher than 6.56 ft (2 m).
OPEN
a. Slide to remove the cover of your sensor.
b. Use a pin to press and hold the Reset button
for 5 seconds until the front LED starts
blinking.
If you have mounted your sensor to a door
or a window, remove the cover as shown
below:
How to reset your sensor to enter pairing mode
a. Remove the cover of your sensor and use a
screwdriver to open the battery cover.
b. Replace the battery with a fresh cell.
How to replace the battery
5s
a. Stick the included adhesives on the
sensor and magnet.
x2
x1
4. Mount Your Sensor
4
0cm 1 2
≤ 0.59 inches (15 mm)
Alignment
Lines
≥ 0.39 inches (10 mm)
OPEN
©2022 TP-Link
Do not ingest battery, Chemical Burn Hazard
This product contains a coin / button cell battery. If the coin / button cell
battery is swallowed, it can cause severe internal burns in just 2 hours and can
lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product
and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
Do not use the device where wireless devices are not allowed.
Please read and follow the above safety information when operating the
device. We cannot guarantee that no accidents or damage will occur due to
improper use of the device. Please use this product with care and operate at
your own risk.
CAUTION!
Avoid replacement of a battery with an incorrect type that can defeat a
safeguard.
Avoid disposal of a battery into re or a hot oven, or mechanically crushing or
cutting of a battery, that can result in an explosion.
Do not leave a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of ammable liquid
or gas; Do not leave a battery subjected to extremely low air pressure that may
result in an explosion or the leakage of ammable liquid or gas.
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/53/EU,
2009/125/EC, 2011/65/EU and (EU) 2015/863.
The original EU declaration of conformity may be
found at https://www.tapo.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Radio Equipment
Regulations 2017.
The original UK declaration of conformity may be found at
https://www.tapo.com/support/ukca/
For EU/UK Region:
Operating Frequency / Nominal Operating Frequency / Max Output Power:
863~865MHz / 863.35MHz / 25mW (e.r.p)
863~865MHz / 864.35MHz / 25mW (e.r.p)
868~868.6MHz / 868.35MHz / 25mW (e.r.p)

Support
For technical support, the user guide and more,
please visit https://www.tapo.com/support/
c. Align the magnet and sensor with no more
than 0.59 inches (15 mm) between them
when the door or window is closed.
Peel the backing from the adhesive and
press the sensor and magnet into place.
b. Choose where you’d like to install the sensor
(but don’t attach it yet). Place the magnet
near the edge of the door or window that
moves.
Notes:
· Leave at least 0.39 inches (10 mm) of space so you can open the
battery compartment.
· Installation height should not be higher than 6.56 ft (2 m).
OPEN
a. Slide to remove the cover of your sensor.
b. Use a pin to press and hold the Reset button
for 5 seconds until the front LED starts
blinking.
If you have mounted your sensor to a door
or a window, remove the cover as shown
below:
How to reset your sensor to enter pairing mode
a. Remove the cover of your sensor and use a
screwdriver to open the battery cover.
b. Replace the battery with a fresh cell.
How to replace the battery
5s
a. Stick the included adhesives on the
sensor and magnet.
x2
x1
4. Mount Your Sensor
4
0cm 1 2
≤ 0.59 inches (15 mm)
Alignment
Lines
≥ 0.39 inches (10 mm)
OPEN
©2022 TP-Link
Do not ingest battery, Chemical Burn Hazard
This product contains a coin / button cell battery. If the coin / button cell
battery is swallowed, it can cause severe internal burns in just 2 hours and can
lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product
and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need
service, please contact us.
Do not use the device where wireless devices are not allowed.
Please read and follow the above safety information when operating the
device. We cannot guarantee that no accidents or damage will occur due to
improper use of the device. Please use this product with care and operate at
your own risk.
CAUTION!
Avoid replacement of a battery with an incorrect type that can defeat a
safeguard.
Avoid disposal of a battery into re or a hot oven, or mechanically crushing or
cutting of a battery, that can result in an explosion.
Do not leave a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of ammable liquid
or gas; Do not leave a battery subjected to extremely low air pressure that may
result in an explosion or the leakage of ammable liquid or gas.
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/53/EU,
2009/125/EC, 2011/65/EU and (EU) 2015/863.
The original EU declaration of conformity may be
found at https://www.tapo.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Radio Equipment
Regulations 2017.
The original UK declaration of conformity may be found at
https://www.tapo.com/support/ukca/
For EU/UK Region:
Operating Frequency / Nominal Operating Frequency / Max Output Power:
863~865MHz / 863.35MHz / 25mW (e.r.p)
863~865MHz / 864.35MHz / 25mW (e.r.p)
868~868.6MHz / 868.35MHz / 25mW (e.r.p)