TP-Link tapo T310 User manual
Meet Your Temperature and Humidity Sensor
Measure the temperature and humidity of the environment and send you instant
notications when the environment changes. It is suitable for green houses, bedrooms,
nursery, incubators, and wine cellars.
Quick Start Guide
Smart Temperature and
Humidity Sensor
7106509722 REV1.0.0
*Images may dier from actual products.
Open the Tapo app and tap the button.
Select Sensors and then your model.
Follow the app instructions to complete
setup.
2. Set Up Your Sensor
Before You Start
A Tapo Hub is required. Make sure your
Tapo Hub is successfully added via the
Tapo app.
OR
2
Remove the battery insulation tab to power
up your sensor. The LED should blink.
Note: If the LED is not blinking, use a pin to press the Reset
button for 5 seconds to reset your sensor and enter pairing
mode.
1. Power Up Your Sensor1
Take your sensor to the preferred location.
Option 1
Single press the Reset button. Your hub
should make a voice prompt.
3. Test Your Sensor
3
Option 2
Blow on the sensor detector. The
temperature and humidity displayed on
the Tapo app should change.
Reset
Sensor
Detector
LED
Battery Pinhole
Use a pin to press and
remove the cover
Reset Button
Single press: Eective range test
Press for 5s: Reset and enter
pairing mode
+
CR2450
Meet Your Temperature and Humidity Sensor
Measure the temperature and humidity of the environment and send you instant
notications when the environment changes. It is suitable for green houses, bedrooms,
nursery, incubators, and wine cellars.
Quick Start Guide
Smart Temperature and
Humidity Sensor
7106509722 REV1.0.0
*Images may dier from actual products.
Open the Tapo app and tap the button.
Select Sensors and then your model.
Follow the app instructions to complete
setup.
2. Set Up Your Sensor
Before You Start
A Tapo Hub is required. Make sure your
Tapo Hub is successfully added via the
Tapo app.
OR
2
Remove the battery insulation tab to power
up your sensor. The LED should blink.
Note: If the LED is not blinking, use a pin to press the Reset
button for 5 seconds to reset your sensor and enter pairing
mode.
1. Power Up Your Sensor1
Take your sensor to the preferred location.
Option 1
Single press the Reset button. Your hub
should make a voice prompt.
3. Test Your Sensor
3
Option 2
Blow on the sensor detector. The
temperature and humidity displayed on
the Tapo app should change.
Reset
Sensor
Detector
LED
Battery Pinhole
Use a pin to press and
remove the cover
Reset Button
Single press: Eective range test
Press for 5s: Reset and enter
pairing mode
+
CR2450
Meet Your Temperature and Humidity Sensor
Measure the temperature and humidity of the environment and send you instant
notications when the environment changes. It is suitable for green houses, bedrooms,
nursery, incubators, and wine cellars.
Quick Start Guide
Smart Temperature and
Humidity Sensor
7106509722 REV1.0.0
*Images may dier from actual products.
Open the Tapo app and tap the button.
Select Sensors and then your model.
Follow the app instructions to complete
setup.
2. Set Up Your Sensor
Before You Start
A Tapo Hub is required. Make sure your
Tapo Hub is successfully added via the
Tapo app.
OR
2
Remove the battery insulation tab to power
up your sensor. The LED should blink.
Note: If the LED is not blinking, use a pin to press the Reset
button for 5 seconds to reset your sensor and enter pairing
mode.
1. Power Up Your Sensor1
Take your sensor to the preferred location.
Option 1
Single press the Reset button. Your hub
should make a voice prompt.
3. Test Your Sensor
3
Option 2
Blow on the sensor detector. The
temperature and humidity displayed on
the Tapo app should change.
Reset
Sensor
Detector
LED
Battery Pinhole
Use a pin to press and
remove the cover
Reset Button
Single press: Eective range test
Press for 5s: Reset and enter
pairing mode
+
CR2450
Meet Your Temperature and Humidity Sensor
Measure the temperature and humidity of the environment and send you instant
notications when the environment changes. It is suitable for green houses, bedrooms,
nursery, incubators, and wine cellars.
Quick Start Guide
Smart Temperature and
Humidity Sensor
7106509722 REV1.0.0
*Images may dier from actual products.
Open the Tapo app and tap the button.
Select Sensors and then your model.
Follow the app instructions to complete
setup.
2. Set Up Your Sensor
Before You Start
A Tapo Hub is required. Make sure your
Tapo Hub is successfully added via the
Tapo app.
OR
2
Remove the battery insulation tab to power
up your sensor. The LED should blink.
Note: If the LED is not blinking, use a pin to press the Reset
button for 5 seconds to reset your sensor and enter pairing
mode.
1. Power Up Your Sensor1
Take your sensor to the preferred location.
Option 1
Single press the Reset button. Your hub
should make a voice prompt.
3. Test Your Sensor
3
Option 2
Blow on the sensor detector. The
temperature and humidity displayed on
the Tapo app should change.
Reset
Sensor
Detector
LED
Battery Pinhole
Use a pin to press and
remove the cover
Reset Button
Single press: Eective range test
Press for 5s: Reset and enter
pairing mode
+
CR2450
Meet Your Temperature and Humidity Sensor
Measure the temperature and humidity of the environment and send you instant
notications when the environment changes. It is suitable for green houses, bedrooms,
nursery, incubators, and wine cellars.
Quick Start Guide
Smart Temperature and
Humidity Sensor
7106509722 REV1.0.0
*Images may dier from actual products.
Open the Tapo app and tap the button.
Select Sensors and then your model.
Follow the app instructions to complete
setup.
2. Set Up Your Sensor
Before You Start
A Tapo Hub is required. Make sure your
Tapo Hub is successfully added via the
Tapo app.
OR
2
Remove the battery insulation tab to power
up your sensor. The LED should blink.
Note: If the LED is not blinking, use a pin to press the Reset
button for 5 seconds to reset your sensor and enter pairing
mode.
1. Power Up Your Sensor1
Take your sensor to the preferred location.
Option 1
Single press the Reset button. Your hub
should make a voice prompt.
3. Test Your Sensor
3
Option 2
Blow on the sensor detector. The
temperature and humidity displayed on
the Tapo app should change.
Reset
Sensor
Detector
LED
Battery Pinhole
Use a pin to press and
remove the cover
Reset Button
Single press: Eective range test
Press for 5s: Reset and enter
pairing mode
+
CR2450
Other manuals for tapo T310
1
Table of contents
Other TP-Link Accessories manuals
TP-Link
TP-Link KASA HS100 KIT V2 Installation instructions
TP-Link
TP-Link TL-PBG6700 User manual
TP-Link
TP-Link HS105 User manual
TP-Link
TP-Link HS100 User manual
TP-Link
TP-Link Kasa Smart KP105 Series User manual
TP-Link
TP-Link HS105 User manual
TP-Link
TP-Link CS100 User manual
TP-Link
TP-Link Tapo P105 User manual
TP-Link
TP-Link TL-PB10400 User manual
TP-Link
TP-Link TL-PBG13400 User manual
TP-Link
TP-Link TL-PB10400 User manual
TP-Link
TP-Link KP115 User manual
TP-Link
TP-Link Kasa Smart KP200 User manual
TP-Link
TP-Link Tapo Camera User manual
TP-Link
TP-Link Tapo P115 User manual
TP-Link
TP-Link WBS210 User manual
TP-Link
TP-Link Tapo Smart Contact Sensor User manual
TP-Link
TP-Link TL-PB15600 User manual
TP-Link
TP-Link tapo Smart Button User manual
TP-Link
TP-Link Tapo D130 User manual
