Traceable 90002-03 User manual

SPECIFICATIONS
Range:
–40° to 176°F / –40° to 80°C (probe)
14° to 176°F / –10° to 80°C (ambient)
Resolution: 0.1°
OPERATION
1. Remove the battery and re-insert it to set the
clock on the unit.After the segment test has
EHHQUXQWKHPLQXWHVFRXQWHUZLOOÀDVK6HW
the minutes by pressing the MIN/MAX button.
Press and hold the MIN/MAX button to
increase the minute counter rapidly until the
button is released. Press the IN/DATE button
WRFRQ¿UPWKHFRUUHFWPLQXWHVHWWLQJ
2. 7KHKRXUFRXQWHUZLOOEHJLQÀDVKLQJ6HWWKH
hour by pressing the MIN/MAX button. Press
and hold the MIN/MAX button to increase
the hour counter rapidly until the button
is released. Press the IN/DATE button to
FRQ¿UPWKHFRUUHFWKRXUVHWWLQJ
3. 7KHPRQWKLQGLFDWRUZLOOEHJLQÀDVKLQJ6HW
the month by pressing the MIN/MAX button.
Press and hold the MIN/MAX button to
increase the counter rapidly until the button
is released. Press the IN/DATE button to
FRQ¿UPWKHFRUUHFWPRQWKVHWWLQJ,IQREXWWRQ
is pressed for 15 seconds, the unit will be set
and will begin recording temperature.
4. To select °F or °C, slide the switch located on
the back of the unit to the desired setting.
5. To switch the display between date and
indoor temperature, press the IN/DATE but-
ton. While in date mode, “DATE” will appear
on the display. While in ambient temperature
mode, “IN” will appear on the display.
6. To recall the stored memories, press the MIN/
MAX button repeatedly and the display will
indicate the following:
Maximum outdoor temperature
Minimum outdoor temperature
Maximum indoor temperature
Minimum indoor temperature
The display will also show the corresponding
date and time that the MIN/MAX readings
occurred. Press the MIN/MAX button again to
return to the current temperature mode.
7. To delete a minimum/maximum memory,
press the MIN/MAX button until the desired
memory is displayed. Press the IN/DATE
button and the displayed memory will be
cleared. Repeat this process to clear each
desired memory.
www. .com [e-mail]1.800.561.8187

TRACEABLE
THERMOMETER
WITH
TIME/DATE
MAX/MIN
MEMORY
INSTRUCTIONS
®
BENCH STAND
The unit is supplied with a bench stand that is a
part of the battery cover. To use the bench stand,
locate the small opening at the bottom of the unit.
3ODFH\RXU¿QJHUQDLOLQWRWKHRSHQLQJDQGÀLSWKH
stand up. To close the stand, simply snap it shut.
WALL MOUNTING THE UNIT
6HWWZRVFUHZVLQWRWKHZDOODWWKHGHVLUHGORFDWLRQ
'RQRWVHWWKHVFUHZÀXVKWRWKHZDOOWKHKHDGVRI
the screws will need to slip into the receptacles on
the back of the unit. Once the screws have been
properly set, hang the unit in place by sliding the
receptacles on the back of the unit over the heads
of the screws.
ALL OPERATIONAL DIFFICULTIES
If this unit does not function properly for any
reason, replace the battery with a new high quality
battery (see “Battery Replacement” section). Low
battery power can occasionally cause any number
RI³DSSDUHQW´RSHUDWLRQDOGLI¿FXOWLHV5HSODFLQJ
the battery with a new fresh battery will solve most
GLI¿FXOWLHV
BATTERY REPLACEMENT
Erratic readings, faint readings, or no display are
all indications that the battery must be replaced.
Remove the battery cover. Remove the exhausted
battery and replace with a newAAAalkaline bat-
tery. Replace the battery cover making certain to
run the probe cable through the slot on the right or
left bottom side of the battery cover. Upon initial
installation of the battery, the time and date will
UHTXLUHVHWWLQJ6HHWKH³2SHUDWLRQ´VHFWLRQ
www. .com [e-mail]1.800.561.8187