Trinity BAMBOO KITCHEN ISLAND W/ DRAWERS User manual

OWNER’S MANUAL
48” BAMBOO KITCHEN ISLAND
W/ DRAWERS

E
1
An electric screwdriver is recommended for ease of assembly.
PARTS LIST
ABC
TOP (1) LEFT
SIDE FRAME (1)
RIGHT
SIDE FRAME (1)
D
UPPER
SHELF (1)
FG
LOWER
SHELF (1)
BACK FRAME (1) LOWER SHELF
FRAME (2)
H
DRAWER
DIVIDER (1)
IJK
DRAWER BACK
PANEL (2)
DRAWER LEFT
PANEL (2)
L
DRAWER RIGHT
PANEL (2)
DRAWER FRONT
PANEL (2)
If you are missing any parts, need assistance with assembly or have questions, please contact our
Customer Service.
Your 48” Bamboo Kitchen Island with Drawers should include the following parts. Please inspect box
contents to ensure you have received all components.

PARTS LIST
2
M
DRAWER BOTTOM
PANEL (2)
SCREW
(34) + (2) extra
black
LONG DRAWER
SCREW (16)
DOWEL
(22) + (2) extra
HANGER STUD (7) NON-LOCKING
CASTER (2)
LOCKING
CASTER (2)
HANDLE (2) HANDLE SCREW (4)
silver
WASHER (4)
SCREWDRIVER (1)
WRENCH (1)
DD EE FF GG
HH II JJ KK
LL MM
AA BB CC
CONNECTOR
SCREW (4)
CAM LOCK (4)

ASSEMBLY INSTRUCTIONS
Lay RIGHT SIDE FRAME (C) on its side. Insert
(2) DOWELS (CC) into each cross beam on
the RIGHT SIDE FRAME (C).
Align holes on UPPER SHELF (D) with
DOWELS (CC) and push onto middle cross
beam on RIGHT SIDE FRAME (C). Align holes
on the LOWER SHELF (E) with DOWELS (CC)
and push onto lower cross beam on RIGHT
SIDE FRAME (C).
Insert (6) SCREWS (AA) through cross beams
of RIGHT SIDE FRAME (C) and fasten tightly
to UPPER SHELF (D) and LOWER SHELF (E)
with SCREWDRIVER (II).
STEP 1
STEP 2
3
AA (6) CC (4)
G (2)
II
E (1) II (1)
E
AA
CC
G
AA (6) CC (4)
D (1)
C (1) II (1)
II
AA
CC
D
C
Lay LOWER SHELF (E) on a clean surface with
holes facing up. Insert (4) DOWELS (CC) in the
inner holes as pictured.
Insert (6) SCREWS (AA) through LOWER SHELF
FRAME (G) and fasten tightly to LOWER SHELF
(E) with SCREWDRIVER (II).
E
Orient LOWER SHELF FRAME (G) with our
logo facing out. Align holes on LOWER SHELF
FRAME (G) with DOWELS (CC) and push onto
LOWER SHELF (E).

ASSEMBLY INSTRUCTIONS
STEP 3
Insert (4) DOWELS (CC) in the LEFT SIDE FRAME
(B). Place (2) on each cross beam as shown.
Screw (2) CONNECTOR SCREWS (LL) to LEFT SIDE
FRAME (B) as shown with SCREWDRIVER (II).
Insert (2) CAM LOCKS (MM) to BACK FRAME (F)
with pointer arrow toward from the edge.
Take LEFT SIDE FRAME (B) and align CONNECTOR
SCREWS (LL) to holes in BACK FRAME (F), then
DOWELS (CC) to UPPER SHELF (D), then LOWER
SHELF (E).
Use the SCREWDRIVER (II) to turn CAM LOCKS
(MM) in clockwise direction until BACK FRAME (F)
is pulled tight with LEFT SIDE FRAME (B).
Insert (6) SCREWS (AA) through cross beams of
LEFT SIDE FRAME (B) and fasten tightly to UPPER
SHELF (D) and LOWER SHELF (E) with the
SCREWDRIVER (II).
STEP 4
4
F
AA
B
II
C
E
D
F
MM (2)
F (1) LL (2) II (1)
LL
MM
Screw (2) CONNECTOR SCREWS (LL) to RIGHT
SIDE FRAME (C) as shown with SCREWDRIVER
(II). Insert (2) CAM LOCKS (MM) to BACK
FRAME (F) with pointer arrow pointing away
from the edge.
Orient BACK FRAME (F) with insert nuts facing
in and long edge with holes up. Push BACK
FRAME (F) onto the CONNECTOR SCREWS (LL)
against RIGHT SIDE FRAME (C).
Use SCREWDRIVER (II) to turn CAM LOCKS
(MM) in clockwise direction until BACK
FRAME (F) is pulled tight with RIGHT SIDE
FRAME (C).
LL
MM
AA (6) CC (4) II (1)
B (1) MM (2)
LL (2)

ASSEMBLY INSTRUCTIONS
With two people, carefully stand partially
assembled Kitchen Island upright.
Take (2) HANDLE SCREWS (KK) and insert
them through the holes on the RIGHT SIDE
FRAME (C) from the inside. Screw them
into HANDLE (JJ) and tighten HANDLE
SCREWS (KK) with SCREWDRIVER (II).
Repeat to install second HANDLE (JJ) on
LEFT SIDE FRAME (B).
By hand, screw (5) HANGER STUDS (DD)
into insert nuts on LEFT SIDE FRAME (B) and
screw (2) HANGER STUDS (DD) into insert
nuts on RIGHT SIDE FRAME (C).
Take a NON-LOCKING CASTER (EE) and insert
threaded stem through WASHER (GG) and
screw into one of the rear legs. Tighten with
WRENCH (HH). Repeat with the other NON-
LOCKING CASTER (EE).
Take a LOCKING CASTER (FF) and insert
threaded stem through WASHER (GG) and
screw into one of the front legs. Tighten with
WRENCH (HH). Repeat with the other
LOCKING CASTER (FF).
Note: Make sure LOCKING CASTERS (FF) are
on the same side.
Use the provided caster wrench to tighten
completely. Failure to do as instructed could
result in the caster stem breaking.
STEP 5
STEP 6
GG (4) HH (1)
FF (2)
EE (2)
FF
EE
HH
GG
KK (4) II (1)
JJ (2) DD (7)
DD
KK
II JJ
C
B
JJ
DD
Hand
5

ASSEMBLY INSTRUCTIONS
Lay TOP (A) on a clean surface with holes
facing up. Insert (3) DOWELS (CC) into
holes in the middle of TOP (A) as shown.
Take DRAWER DIVIDER (H) and orient the
notch toward the long strip of wood on
TOP (A). Align the holes to the DOWELS
(CC) and push DRAWER DIVIDER (H) firmly
onto TOP (A).
Insert (4) SCREWS (AA) through the blocks
on TOP (A) and fasten them tightly to
DRAWER DIVIDER (H) with SCREWDRIVER
(II).
STEP 7
Insert a DOWEL (CC) into the top of each leg.
Insert (3) DOWELS (CC) to the BACK FRAME
(F).
With two people, lift TOP (A) and align the
holes on the underside with the DOWELS (CC)
on the Kitchen Island Frame. Carefully lower
TOP (A) onto the Kitchen Island Frame.
Take (2) SCREWS (AA) and insert through each
block on the underside of TOP (A) as shown.
Tighten all SCREWS (AA) with the
SCREWDRIVER (II).
STEP 8
AA (4) CC (3)
H (1)
A (1) II (1)
II
AA
CC
A
AA (12) CC (7) II (1)
6
II
AA
CC
H
F

ASSEMBLY INSTRUCTIONS
Align and press dowels on DRAWER FRONT
PANEL (I) and DRAWER BACK PANEL (J) into
blind holes on DRAWER RIGHT PANEL (L).
Insert (4) DRAWER SCREWS (BB) through the
DRAWER RIGHT PANEL (L) and fasten them
tightly to DRAWER FRONT PANEL (I) and
DRAWER BACK PANEL (J) with SCREWDRIVER
(II).
Slide DRAWER BOTTOM PANEL (M) into the
grooves as shown.
Repeat for second Drawer.
STEP 9
7
STEP 10
Align and press dowels on DRAWER FRONT
PANEL (I) and DRAWER BACK PANEL (J) into
blind holes on DRAWER LEFT PANEL (K).
Insert (4) DRAWER SCREWS (BB) through the
DRAWER LEFT PANEL (K) and tightly fasten
them with SCREWDRIVER (II).
Repeat for second Drawer.
M (2) BB (8)
L (2)
K (2)
II (1)
J (2)
I (2)
LII
BB
J
I
M
II (1)
BB (8)
II
BB
K

USAGE INSTRUCTIONS
Align rails on Drawer with rails on the
Kitchen Island. Push Drawer all the way into
Kitchen Island.
Install Drawers
Pull one Drawer out so that it is almost fully
extended. On the LEFT-hand side, pull the
black release lever UP. On the RIGHT-hand
side, push the black release lever DOWN.
While holding the levers as instructed, pull
the Drawer forward until released from the
slides attached to the Kitchen Island.
Remove Drawers
8

(see page 11 for exploded parts view)
9
Part Number Description Part Number Description
1) Drawer Right Panel 16) Wrench
2) Drawer Bottom 17) Washer
3) Drawer Front 18) Non-locking Caster
4) Top Front Frame 19) Left Side Frame
5) Connector Screw 20) Hanger Stud
6) Cam Lock 21) Handle
7) Slide (frame side) 22) Handle Screw
8) Long Drawer Screw 23) Back Frame
9) Right Side Frame 24) Drawer Divider
10) Upper Shelf 25) Dowel
11) Locking Caster 26) Top
12) Lower Shelf 27) Slide (drawer side)
13) Lower Shelf Frame 28) Drawer Left Panel
14) Screw 29) Drawer Back Panel
15) Screwdriver
SERVICE PARTS LIST –NATURAL
Customer Service provides the following replacement parts: