Trotec TTK 96 E User manual

TRT-BA-TTK96E-TTK127E-TC-001-EN
TTK 96 E / TTK 127 E
EN
OPERATING MANUAL
DEHUMIDIFIER

1 EN
Operating manual – dehumidifier TTK 96 E / TTK 127 E
Table of contents
Notes regarding the operating manual.................................1
Safety .....................................................................................2
Information about the device................................................3
Transport and storage...........................................................4
Assembly ...............................................................................4
Set-up and installation..........................................................5
Operation ...............................................................................5
Errors and faults....................................................................8
Maintenance ..........................................................................9
Technical annex...................................................................11
Declaration of conformity ...................................................14
Notes regarding the operating manual
Symbols
Hazardous electric current!
Warns about hazards from electric current which can
lead to injuries or even death.
Danger!
Warns of a hazard which can lead to personal injury.
Caution!
Warns of a hazard which can lead to property damage.
The current version of the operating manual can be found at:
TTK 96 E
http://download.trotec.com/?sku=1120000101&id=1
TTK 127 E
http://download.trotec.com/?sku=1120000126&id=1
Legal notice
This release replaces all previous versions. No part of this
publication may be reproduced without written permission from
Trotec. The same applies for electronically processing,
duplicating or spreading the publication. Subject to technical
changes. All rights reserved. Trademarks are used without
guarantee that they may be used freely and primarily following
the spelling of the manufacturer. Product names are registered.
Changes to construction in the interests of constant
improvements to the product, as well as changes to the shape
and colour are reserved.
The scope of delivery may vary from product images. This
document was created with all due care. Trotec accepts no
liability whatsoever for possible mistakes or omissions.
© Trotec
Warranty and liability
The device complies with the fundamental health and safety
requirements of the applicable EU regulations and was tested at
the factory for perfect functionality multiple times.
However, if faults in the functionality occur and cannot be
remedied with the measures in the chapter Errors and faults,
please get in touch with your dealer or distributor.
When making a warranty claim, supply the device number (see
the rear of the device).
When manufacturer's instructions or legal regulations have not
been followed, or after unauthorised changes to the device are
made, the manufacturer is not responsible for the resulting
damages. Changes to the device or unauthorised replacement
of individual parts can drastically impact the electrical safety of
this product and leads to the forfeit of the warranty. Liability
does not extend to damages to people or property caused by the
device being used other than as described in the instructions in
this operating manual. Subject to changes to technical design
and model changes as part of constant development and
product improvement without prior notice.
No liability is accepted for damages resulting from improper
use. In such a case, any warranty claims be voided also.

EN 2
Operating manual – dehumidifier TTK 96 E / TTK 127 E
Safety
Carefully read this manual before starting / using the
device and keep it within reach.
• Do not use the device in potentially explosive rooms.
• Do not use the device in aggressive atmosphere.
• Set the device up in an upright and stable position.
• Ensure that the air inlet and outlet are not obstructed.
• Ensure that the side of the device where the air inlet is
found is kept free of dirt and loose objects.
• Never reach or put objects into the device.
• Do not cover or transport the device during operation.
• Do not use the device with wet or damp hands.
• Ensure that all electric cables outside of the device are
protected from damage (e.g. from animals). Never use the
device if the cable or power connection is damaged!
• Only use extensions to the connecting cable which are
appropriate to the device power consumption, the length of
its cable and its use. Completely unroll extension cables.
Avoid electrical overload.
• Only transport the device in an upright position with an
emptied condensation tank.
• Dispose of the collected condensate. Do not drink it. Health
hazard!
• Pull the plug from the socket if the device is not in use.
• Unplug the device from the mains before starting with
maintenance, service or repair work.
Intended use
Only use the device TTK 96 E / TTK 127 E for drying and
dehumidifying room air, while adhering to and following the
technical data.
Intended use comprises:
• drying and dehumidifying:
– living rooms, bedrooms or basements
– laundries, holiday homes.
• maintaining the dryness of:
– storage spaces, archives, laboratories, garages
– changing rooms etc.
Improper use
Do not place the device TTK 96 E / TTK 127 E on wet or flooded
ground. Do not use the device outdoors. Do not place any
objects, e.g. wet clothing, on the device for drying.
Any unauthorised changes, modifications or alterations to the
device are forbidden.
Personnel qualifications
People who use this device must:
• be aware of the dangers that occur when working with
electric devices in damp areas.
• have read and understood the operating manual, especially
the Safety chapter.
Residual risks
Hazardous electric current!
Work on the electrical components must only be
carried out by an authorised specialist company!
Hazardous electric current!
Before any work on the device, remove the mains plug
from the mains socket!
Danger!
The device is not a toy and does not belong in the
hands of children.
Danger!
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!
Danger!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Caution!
To avoid damages to the device, do not operate the
device without an air filter inserted!
Behaviour in the event of an emergency
1. In an emergency, disconnect the device from the mains
feed-in: Switch the device off and disconnect it from the
mains.
2. Do not reconnect a defective device to the mains.

3 EN
Operating manual – dehumidifier TTK 96 E / TTK 127 E
Information about the device
Description of the device
The device TTK 96 E / TTK 127 E uses the principle of
condensation to automatically dehumidify rooms.
The fan sucks damp room air through the air inlet, the air filter,
the evaporator and to the condenser located behind it. The air is
cooled at the cold evaporator until it is below the dew point.
Water vapour contained in the room air precipitates on the
evaporator fins as either condensation or rime. The
dehumidified, cooled air is slightly warmed and blown out again.
The drier air thus conditioned mixes with the air in the room.
The humidity in the room where the device is positioned is
reduced as air constantly circulates through the device.
Depending on the air temperature and the relative humidity, the
condensed water either drops continuously or only during the
defrost phase through the integrated drain nozzle into the
condensation tank below. It is fitted with a float to measure the
filling level.
The device has a control panel for operating and controlling the
functions.
Once the maximum fill level of the condensation tank is
reached, the condensation tank indicator light (see chapter
Operating elements) on the control panel is illuminated. The
device switches off. The condensation tank indicator light only
goes out again once the emptied condensation tank is
reinserted.
Optionally, the condensed water can be drained by attaching a
hose (Ø = 14mm) at the condensation connection.
The device can reduce the relative humidity of a room to approx.
35%.
Because of the heat radiation generated during operation, the
room temperature may rise slightly.
Device depiction
1
2
3
11
10
9
8
74
12
6
5
No. Designation
1 Transport handle
2 Air outlet
3 Power cable holder
4 Wheels
5 Hose adapter for condensation drain hose
6 Condensation drain hose
7 Power cable
8 Condensation hose connection with sealing cap
9 Air inlet with air filter
10 Filling level indication
11 Condensation tank
12 Control panel

EN 4
Operating manual – dehumidifier TTK 96 E / TTK 127 E
Transport and storage
Transport
To make the device easier to transport, it is fitted with wheels.
Before transporting the device, proceed as follows:
1. Pump out any possibly remaining condensate. Check for
dripping condensation.
2. Pull the plug from the mains socket. Do not use the power
cable to drag the device.
3. Only wheel the device on a level and smooth surface.
Storage
Leave the device to rest for 24hours before storing it. Then
empty and clean the condensation tank, the filter and the device
prior to storing.
When the device is not being used, observe the following
storage conditions:
• Dry.
• In an upright and stable position.
• Protected from dust and direct sunlight.
• With a cover to protect it from invasive dust, if necessary.
Assembly
Scope of delivery
• 1x dehumidifier
• 1x air filter
• 1x power cable holder
• 1x hose adapter for condensation drain hose
• 1x condensation drain hose (l = 60cm, Ø = 14mm)
Assembling the power cable holder
1. Unpack the device and remove the cardboard box as well as
any other outer packaging.
2. Remove the condensation tank.
3. Remove the power cable holder(3), the condensation drain
hose(6) and the hose adapter(5) from the condensation
tank.
4. Put the condensation tank back in.
5. Press the holder into the provided recess.
ðThe holder should click into place.
6. Check the holder for tight fit.
ðIf needed, you may now wind the power cable around the
holder.

5 EN
Operating manual – dehumidifier TTK 96 E / TTK 127 E
Set-up and installation
Positioning
When positioning the device, observe the minimum distance
from walls or other objects as described in chapter Technical
Data.
• Set the device up in a level and stable position.
• When positioning the device, keep a sufficient distance to
heat sources.
• When positioning the device, particularly in wet areas,
secure it locally with an RCD (residual current device)
which complies with the respective regulations.
Operation
• After being switched on, the device operates fully
automatically.
• The fan is running continuously until the device is switched
off.
• Avoid open doors and windows.
Operating elements
On
Off
Full
Auto defrost
13 14 17 18 19 20
212223242526
15 16
27
No. Designation Meaning
13 FILTER LED Illuminated when the filter needs to be
cleaned.
14 Auto defrost LED Illuminated when the device carries out an
automatic defrost.
15 CONT. LED Illuminated when the device runs in
continuous operation.
16 TURBO LED Illuminated when the fan runs at maximum
power.
17 FULL LED Illuminated when the condensation tank is
full. See chapter Emptying the condensation
tank
18 Off LED Illuminated when the timer is programmed for
automatic switch-off.
19 On LED Illuminated when the timer is programmed for
automatic switch-on.
20 Display Indicates the current humidity level.
Indicates the selected humidity value during
the humidity setting.
Indicates the number of hours during the
timer setting.
21 POWER button Switches the device on or off.
22 Selection button Selection button for the humidity level (35%
to 85% in increments of 5%) or the timer
function (0 to 10h in increments of 0.5hours
or 10 to 24h in increments of 1h)
23 TIMER button Switches the timer function on or off.
24 TURBO button Sets the fan stage.
Stage 1 = normal
Stage 2 = function for drying laundry
25 CONT. button Switches continuous operation on or off.
26 FILTER button Resets the cleaning cycle for the filter.
27 COMFORT button Switches comfort mode on or off.

EN 6
Operating manual – dehumidifier TTK 96 E / TTK 127 E
Inserting the air filter
Make sure that the air filter is installed before switching the
device on.
The device should not be operated without air filter. Without air
filter the inside of the device will be heavily contaminated,
which affects the dehumidification performance adversely and
may further result in damage to the device.
Switching the device on
1. Ensure that the condensation tank is empty and inserted
correctly.
2. Insert the mains plug into a properly secured mains socket.
3. Press the POWER button(21).
Setting the humidity level
You can adjust the preset humidity level at any time during
operation.
1. Press the left or right-hand side of the selection button(22)
to adjust the desired humidity level.
ðThe desired humidity level will be indicated on the
display(20) for approx.5s.
ðThen the currently measured humidity level reappears on
the display.
ðThe device switches off automatically upon reaching the
desired humidity level.
Setting the fan stage
1. Press the TURBO button(24) to switch between the normal
and maximum fan stage.
ðThe TURBO LED(16) is illuminated when the fan runs at
maximum power.
ðThe function for drying laundry is activated.
Continuous operation mode
In continuous operation mode, the device dehumidifies the air
constantly, regardless of the humidity.
Note:
For continuous operation mode the condensation drain hose
should be connected in order to continuously drain the
accumulating condensate.
1. Press the CONT. button (25) to switch continuous operation
on or off.
ðWith activated continuous operation mode the CONT.
LED(15) is illuminated.
Function for drying laundry
The device may be used to dry clothes in a more timely manner.
When positioning the device or a clothes horse please observe
the minimum distances specified in the technical data.
1. Press the TURBO button(24) to set the maximum fan stage
(stage2).
ðThe TURBO LED(16) is illuminated.
ðThe function for drying laundry is activated.
Comfort mode
Comfort mode ensures an agreeable humidity level ranging
between 45% and 55%. The humidity level is regulated
automatically between the values 45% - 50% - 55%.
In this operating mode it is not possible to regulate the humidity
level manually.
1. Press the COMFORT button(27) to switch comfort mode on
or off.
Operation with hose attached to the condensation
connection
For a continuous dehumidification (continuous operation mode)
the condensation drain hose should be connected to the device.
üThe hose included in the scope of delivery is ready for use.
üThe hose adapter included in the scope of delivery is ready
for use.
üThe device is switched off.
1. Unscrew the sealing cap from the connection.
2. Screw the hose adapter(5) onto the connection.
3. Push one end of the hose onto the hose adapter.

7 EN
Operating manual – dehumidifier TTK 96 E / TTK 127 E
4. Guide the other hose end to a suitable drain or sufficiently
dimensioned collection container. Please observe that the
hose must not be kinked.
Disassemble the hose again when no longer operating the
device continuously. Allow hose and hose adapter to dry prior to
storage.
Setting the timer
For the device to switch on or off automatically after a
predefined number of hours (max. 24hrs) you can programme
the timer. It is possible for the switch-on time and the switch-off
time to be activated at the same time, if so, both LEDs(18 and
19) will be illuminated.
The timer can be programmed in increments of 0.5hours (0 to
10h) or in increments of 1hour (10 to 24h).
Note:
Do not leave the operating device unattended in a freely
accessible room with an activated timer.
1. Press the TIMER button(23) to activate the timer.
ðThe Off LED(18) is illuminated.
ðThe display indicates the number of hours until
automatic switch-off (default: 0.0).
2. Press the selection button(22) to choose the number of
hours until automatic switch-off.
3. Alternatively, press the TIMER button(23) again to
programme automatic switch-on.
ðThe On LED(19) is illuminated.
ðThe display indicates the number of hours until
automatic switch-on (default: 0.0).
4. Press the selection button(22) until the desired number of
hours until automatic switch-on has been set.
ðThe number of hours is indicated on the display for
approx.5s. Then the current humidity level of the room
will be indicated.
5. It keeps running until the given switch-off time has expired
or until the device is switched off manually.
ðThe device switches off or on after the predefined time.
ðThe corresponding LED (Off for automatic switch-off or On
for automatic switch-on) is illuminated.
Note:
You can deactivate automatic switch-on and switch-off by
setting the respective number of hours back to 0.
When P2 is indicated on the display, the timer is also
deactivated.
Automatic defrost
At low ambient temperatures the evaporator can freeze up
during dehumidification. The device will then carry out an
automatic defrost. The compressor switches off and the fan
keeps running until defrosting is completed.
The duration of the defrost process can vary. Do not switch off
the device during automatic defrost. Do not remove the mains
plug from the mains socket.
Memory function
In case of brief power failures the device memorizes the
programmed nominal value for humidity. The pre-programmed
start and stop times for automatic operation are not saved.
Auto stop function
If the water tank is full, not inserted correctly or the set humidity
level has been reached, the device stops automatically.

EN 8
Operating manual – dehumidifier TTK 96 E / TTK 127 E
Shutdown
Danger!
Do not touch the mains plug with wet or damp hands.
1. Press the POWER button(21).
2. Remove the mains plug from the mains socket.
3. If necessary, remove the condensation drain hose and any
residual fluid from it.
4. Empty the condensation tank, if need be.
5. Clean the device, and especially the air filter, according to
the chapter Maintenance.
6. Store the device according to the chapter Storage.
Errors and faults
The device has been checked for proper functioning several
times during production. If malfunctions occur nonetheless,
check the device according to the following list.
Note:
Wait for at least 3 minutes after maintenance and repair work.
Only then switch the device back on.
The device does not start:
• Check the power connection.
• Check the mains plug for damages.
• Check the condensation tank for correct seating. Check the
filling level of the condensation tank and empty it, if
necessary. The indicator lightmust not light up.
• Wait for 10 minutes before restarting the device. If the
device is not starting, have the electrics checked by a
specialist company or by Trotec.
The device is running, but no condensate forms:
• Check the float in the condensation tank for dirt. If
necessary, clean the condensation tank. The float must be
able to move freely.
• Check the room temperature. Observe the device's
permissible operating range according to the technical
data.
• Check the air filter for dirt. If necessary, clean or replace
the air filter.
• From the outside, check the condenser for dirt (see
chapter Maintenance). If your condenser is dirty, have it
cleaned by a specialist company or by Trotec.
The device is loud or vibrates; condensate is leaking:
• Check whether the device is standing upright and on an
even surface.
The device gets very warm, is loud or loses power:
• Check the air inlets and air filter for dirt. Remove external
dirt.
• From the outside, check the device for dirt (see chapter
Maintenance). If the inside of the device is dirty, have it
cleaned by a specialist company or by Trotec.
Your device still does not operate correctly after these
checks?
Have the device repaired by authorised expert staff or by Trotec.
Error codes
The following error codes can be displayed:
Error code Cause Remedy
AS Error humidity sensor Disconnect the device briefly from
the mains.
Should the error still be displayed
after the restart, please contact
the customer service.
ES Error at the temperature
sensor of the evaporator
Disconnect the device briefly from
the mains.
Should the error still be displayed
after the restart, please contact
the customer service.
P2 Condensation tank full or
not inserted correctly
Empty the condensation tank or
check the condensation tank for
correct fit.
EC Leakage in the refrigerant
circuit
Switch the device off and contact
the customer service.
Also see the information regarding
the refrigerant circuit in chapter
Maintenance.
E3 General fault at the device Disconnect the device briefly from
the mains.
Should the error still be displayed
after the restart, please contact
the customer service.

9 EN
Operating manual – dehumidifier TTK 96 E / TTK 127 E
Maintenance
Activities required before starting maintenance
• Do not touch the mains plug with wet or damp hands.
• Before any work, remove the mains plug!
Danger!
Maintenance tasks which require the housing to be
opened must only be carried out by authorised
specialist companies or by Trotec.
Visual inspection of the inside of the device for dirt
1. Remove the air filter.
2. Use a torch to illuminate the openings of the device.
3. If you see a thick layer of dust, have the inside of the device
cleaned by a specialist company for cooling and air-
conditioning or by Trotec.
4. Put the air filter back in.
Cleaning the housing
Clean the device with a soft, damp and lint-free cloth. Ensure
that no moisture enters the housing. Do not use abrasive
cleaners.
Refrigerant circuit
• The entire refrigerant circuit is a maintenance-free,
hermetically sealed system and may only be maintained or
repaired by specialist companies for cooling and air-
conditioning or by Trotec.
Cleaning the air filter
Caution!
Ensure that the air filter is not worn or damaged. The
corners and edges of the air filter must not be
deformed or rounded. Before reinserting the air filter,
make sure that it is undamaged and dry!
The air filter must be cleaned after 250operating hours at the
latest or as soon as it is dirty. This is brought to light e.g. by a
reduced cooling capacity (see chapter Errors and faults).
The FILTER LED(13) will be illuminated after 250operating
hours.
1.
2.
• Reinsert the cleaned, dry filter in the device in reverse
order.
• Press the FILTER button(26) to carry out a filter reset. This
is only possible when the FILTER LED(13) was illuminated
previously. The FILTER LED(13) goes out after the reset.
Note:
If the device stops, it cannot be restarted within the next
3minutes so as to protect the device. After 3minutes the
device starts automatically.

EN 10
Operating manual – dehumidifier TTK 96 E / TTK 127 E
Emptying the condensation tank
If the condensation tank is full or not inserted correctly, the Full
LED(17) lights up the the message P2 appears on the display.
Compressor and fan will switch off.
1. Take the condensation tank out of the device.
2. Empty the condensation tank over a drain or sink.
3. Rinse the tank with clear water. Clean the tank regularly
using a mild cleaning agent (no detergent!).
4. Refit the condensation tank into the device. In doing so,
make sure that the condensation tank is inserted correctly,
for otherwise the device cannot be switched back on.

11 EN
Operating manual – dehumidifier TTK 96 E / TTK 127 E
Technical annex Technical data
Parameter Value
Model TTK 96 E TTK 127 E
Max. dehumidification performance 30 l / 24 h 50 l / 24 h
Dehumidification performance @ 30°C and 80%
RH
28.3 l / 24 h 46.8 l / 24 h
Air volume [m3/h] stage 1: 180
stage 2: 210
stage 1: 320
stage 2: 345
Ambient temperature 5°C - 35°C 5°C - 35°C
Operating range relative humidity 35 % - 100 % RH 35 % - 100 % RH
Mains connection 1/N/PE~ 230 V / 50 Hz 1/N/PE~ 230 V / 50 Hz
Power consumption 465 W 775 W
Nominal current 2.5 A 3.6 A
Refrigerant R410A R410A
Amount of refrigerant 220 g 290 g
Condensation tank 3 l 6 l
Sound pressure level 52 dB (A) 51 dB (A)
Dimensions (length x width x height) 386 x 260 x 500 (mm) 392 x 282 x 616 (mm)
Minimum distance to walls and other objects top: 40 cm
front: 20 cm
rear: 20 cm
right: 20 cm
left: 40 cm
top: 40 cm
front: 20 cm
rear: 20 cm
right: 20 cm
left: 40 cm
Weight 15.3 kg 19.8 kg
Wiring diagram
TTK 96 E
',63/$<%2$5'
0$,1%2$5')$132:(5
CN13
CN1
CN3
CN5
4
3
P8
CN8
P4
CN2
COMP.
CAPACITOR
WATER
SWITCH1
PIPE
TEMP.
HUMI.
SENSOR
BLACK(or BROWN)
RED
WHITE(or BLUE)
WHITE
RED
Y/G
BLUE
Y/G(or GREEN)
BLACK
RY1
BLACK
BLUE
BROWN
FAN
CAPACITOR
Y/G
R
C
S
0
a
&203
WATER
SWITCH2
&SWITCH3
CN7
P9
P10
RED
BLACK
RED
BLACK
P6
P11
BLUE
7KLVV\PEROLQGLFDWHVWKHHOHPHQWLVRSWLRQDOWKHDFWXDOVKDSHVKDOOSUHYDLO
Notes:
OverLoad
Protector
,21
Y/G
%\SDVV9DOYH
3803
Y/G
P7
P5
BLUE
BLUE
'&32:(5%2$5'
CN2 CN1
RED
BLACK
TTK 127 E
',63/$<%2$5'
0$,1%2$5')$132:(5
CN13
CN1
CN3
CN5
4
3
P8
CN8
P4
CN2
COMP.
CAPACITOR
WATER
SWITCH1
PIPE
TEMP.
HUMI.
SENSOR
BLACK(or BROWN)
RED
WHITE(or BLUE)
WHITE
RED
Y/G
BLUE
Y/G(or GREEN)
BLACK
RY1
BLACK
BLUE
BROWN
FAN
CAPACITOR
Y/G
R
C
S
0
a
&203
WATER
SWITCH2
&SWITCH3
CN7
P9
P10
RED
BLACK
RED
BLACK
P6
P11
BLUE
7KLVV\PEROLQGLFDWHVWKHHOHPHQWLVRSWLRQDOWKHDFWXDOVKDSHVKDOOSUHYDLO
Notes:
OverLoad
Protector
,21
Y/G
%\SDVV9DOYH
3803
Y/G
P7
P5
BLUE
BLUE
'&32:(5%2$5'
CN2 CN1
RED
BLACK

EN 12
Operating manual – dehumidifier TTK 96 E / TTK 127 E
Spare parts drawing and list TTK 96 E
Note!
The position numbers of the spare parts differ from those describing
the positions of other parts mentioned in this operating manual.
16
1
22.1
2.2
2.3
2.4
2.1.1
2.1.2
2.1.3
3
3.1 3.2
3.3 3.4
4
5
6
7
8
9
10
11
12 12.1.4
12.1.1
12.1.3
12.1.2
15
14
2.5
17
17.1
18
18.1
18.2
18.3
18.4
18.5
19
20
21
17.2
12.1
20.1
20.2
12.2
13
No. Spare part No. Spare part No. Spare part
1 Front panel assembly 6 Fixed speed rotary compressor 17 Parts of middle clapboard
2 Water Tank Assembly 7 Parts of compressor return pipe 17.1 Parts of middle clapboard
2.1 Water Tank Subassembly 8 Capillary Assembly 17.2 Micro Switch
2.1.1 Water Tank Panel 9 Evaporator assembly Gas valve assembly 18 Electronic control box assembly
2.1.2 Water Tank 10 Condenser Assembly 18.1 Electrical Control Box
2.1.3 Water Tank Cover 11 Parts of compressor exhaust pipe 18.2 Mounting rack of main control panel
2.2 Handle for Tank 12 Rear Panel assembly 18.3 Main control board assembly
2.3 Floater 12.1 Rear Panel Subassembly 18.4 Capacitor
2.4 Buoy foam 12.1.1 Right Side Plate 18.5 Humidity Sensor Board Subassembly
2.5 Winding Eyebolt 12.1.2 Left Side Floor 19 Electrical Control Box Cover Subassembly
3 Scroll assembly 12.1.3 Top cover 20 Chassis Assembly
3.1 VoluteScroll 12.1.4 Rear panel 20.1 Chassis Subassembly
3.2 Centrifugal Fan 12.2 Structure Subassembly of Display Box 20.2 Universal wheel
3.3 Single-phase Asynchronous Motor 13 Connecting joint assembly 21 Power Supply Cable Subassembly
3.4 Fan Motor Holder 14 Water Drain Connector rating label
4 Capacitor Cap 15 Filter inlet air grille user&installation manual
5 Capacitor 16 Temperature Sensor package box

13 EN
Operating manual – dehumidifier TTK 96 E / TTK 127 E
TTK 127 E Note!
The position numbers of the spare parts differ from those describing
the positions of other parts mentioned in this operating manual.
16
1
22.1
2.2
2.3
2.4
3
3.1 3.2
3.3 3.4
4
5
6
7
8
9
10
11
12 12.1
12.2
12.4
12.3
15
14
2.5
17
17.1
18
18.1
18.2
18.3
18.4
18.5
19
20
20.1
21
17.2
12.5
20.2
13
No. Spare part No. Spare part No. Spare part
1 Front Panel 7 Parts of compressor return pipe 17 Parts of middle clapboard
2 Water Tank Assembly 8 Capillary Assembly 17.1 Parts of middle clapboard
2.1 Water Tank Subassembly 9 Evaporator assembly Gas valve assembly 17.2 Micro Switch
2.2 Handle for Tank 10 Condenser Assembly 18 E-Parts Box assembly
2.3 Floater 11 Parts of compressor exhaust pipe 18.1 Electrical Control Box
2.4 Buoy foam 12 Rear Panel assembly 18.2 Mounting rack of main control panel
2.5 Winding Eyebolt 12.1 Rear panel 18.3 Main Control Board Subassembly(Sticker)
3 Scroll assembly 12.2 Right Side Plate 18.4 Capacitor
3.1 VoluteScroll 12.3 Left Side Floor 18.5 Humidity Sensor Board Subassembly
3.2 Centrifugal Fan 12.4 Top cover 19 Electrical Control Box Cover Subassembly
3.3 Single-phase Asynchronous Motor 12.5 Structure Subassembly of Display Box 20 Chassis Assembly
3.4 Fan Motor Holder Subassembly 13 20.1 Chassis Subassembly
4 Capacitor Cap 14 Water Drain Connector 20.2 Universal wheel
5 Capacitor 15 Filter 21 Power Supply Cable Subassembly
6 Fixed speed rotary compressor 16 Temperature Sensor

EN 14
Operating manual – dehumidifier TTK 96 E / TTK 127 E
Disposal
In the European Union, electronic equipment must not be
treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2002/96/EC of the
European Parliament and of the Council of 27January 2003 on
waste electrical and electronic equipment (WEEE). At the end of
its life, please dispose of this device according to the valid legal
requirements.
The device uses an environmentally and ozone-neutral cooling
agent (see Technical Data).
Dispose of the refrigerant appropriately and according to the
national regulations.
Declaration of conformity
in accordance with the EC Low Voltage Directive 2006/95/EC
and the EC Directive 2004/108/EC about electromagnetic
compatibility.
Herewith, we declare that the device TTK 96 E / TTK 127 E was
developed, constructed and produced in compliance with the
named EC directives.
Applied standards:
EN 55014-1:2006 +A1:2009 +A2:2011
EN 55014-2:1997 +A1:2001 +A2:2008
EN 61000-3-2:2006 +A1:2009 +A2:2009
EN 61000-3-3:2013
EN 60335-1:2012
EN 60335-2-40:2003 +A11:2004 +A12:2005 +A1:2006
+A2:2009 +A13:2012
EN 62233:2008
ZEK 01.4-08
The marking is found on the rear of the device.
Manufacturer:
Trotec GmbH & Co. KG
Grebbener Straße 7
D-52525 Heinsberg
Phone: [phone]
Fax: [phone]
E-mail: [email protected]
Heinsberg, 10.03.2015
Detlef von der Lieck
Managing Director

Trotec GmbH & Co. KG
Grebbener Str. 7
D-52525 Heinsberg
[phone]
[phone]
[email protected]
www.trotec.com