turck BI10-G30-Y2X 7M User manual

Inductive sensor
BI10-G30-Y2X 7M
Edition • 2016-05-14T06:55:02+02:00
1 / 4 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. [phone] ñ Fax [phone] ñ [email protected] ñ www.turck.com
Type code BI10-G30-Y2X 7M
Ident no. 1060601
Rated switching distance Sn 10 mm
Mounting conditions flush
Assured switching distance ð (0,81 x Sn) mm
Correction factors St37 = 1; Al = 0.3; stainless steel = 0.7; Ms = 0.4
Repeatability ð 2 % of full scale
Temperature drift ð ± 10 %
Hysteresis 1…10 %
Ambient temperature -25…+70 °C
Output function 2-wire, NAMUR
Switching frequency 0.5 kHz
Voltage Nom. 8.2 VDC
Non-actuated current consumption ï 2.1 mA
Actuated current consumption ð 1.2 mA
Approval acc. to BVS 04 ATEX E 202
Internal capacitance (Ci) / inductance (Li) 150 nF / 150 µH
Device designation É IM1 Ex ia I
(max. Ui = 15 V, Ii = 60 mA, Pi = 200 mW)
Construction Threaded barrel, M30 x 1.5
Dimensions 44 mm
Housing material Metal, CuZn, chrome-plated
Active area material Plastic, PA
End cap Plastic, EPTR
Max. tightening torque housing nut 75 Nm
Connection cable
Cable quality 5.2 mm, blue, LifYY, PVC, 7m
Cable cross section 2 x 0.34 mm2
Vibration resistance 55 Hz (1 mm)
Shock resistance 30 g (11 ms)
Protection class IP67
MTTF 6198 years acc. to SN 29500 (Ed. 99) 40 °C
Switching state LED yellow
■ATEX category I M1, mining
■Threaded barrel, M30 x 1.5
■Chrome-plated brass
■DC 2-wire, nom. 8.2 VDC
■Output acc. to DIN EN 60947-5-6 (NA-
MUR)
■Cable connection
Wiring Diagram
Functional principle
Inductive sensors detect metal objects con-
tactless and wear-free. For this, they use a
high-frequency electromagnetic AC field that
interacts with the target. Inductive sensors
generate this field via an RLC circuit with a
ferrite coil.

Inductive sensor
BI10-G30-Y2X 7M
Edition • 2016-05-14T06:55:02+02:00
2 / 4 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. [phone] ñ Fax [phone] ñ [email protected] ñ www.turck.com
Distance D 2 x B
Distance W 3 x Sn
Distance T 3 x B
Distance S 1.5 x B
Distance G 6 x Sn
Diameter of the active area B Ø 30 mm

Inductive sensor
BI10-G30-Y2X 7M
Edition • 2016-05-14T06:55:02+02:00
3 / 4 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. [phone] ñ Fax [phone] ñ [email protected] ñ www.turck.com
Accessories
Type code Ident no. Description
QM-30 6945103 Quick-mount bracket with dead-stop; material: Chrome-plat-
ed brass Male thread M36 x 1.5. Note: The switching dis-
tance of proximity switches can be reduced by the use of
quick-mount brackets.
BST-30B 6947216 Fixing clamp for threaded barrel devices, with dead-stop; ma-
terial: PA6
MW-30 6945005 Mounting bracket for threaded barrel devices; material: Stain-
less steel A2 1.4301 (AISI 304)
BSS-30 6901319 Mounting bracket for smooth and threaded barrel devices;
material: Polypropylene
MS13-22EX0-R 5322203

Inductive sensor
BI10-G30-Y2X 7M
Edition • 2016-05-14T06:55:02+02:00
4 / 4 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. [phone] ñ Fax [phone] ñ [email protected] ñ www.turck.com
Operating manual
Intended use
This device fulfills the directive 94/9/EC and is suited for use in explosion hazardous areas according to EN 60079-0 (2012), EN 60079-11
(2012) and EN 50303 (2000).
In order to ensure correct operation to the intended purpose it is required to observe the national regulations and directives.
For use in explosion hazardous areas conform to classification
I M 1 (Group I, Category M 1, electrical equipment for mining).
Marking (see device or technical data sheet)
É I M 1 and Ex ia I acc. to EN 60079-11
Installation / Commissioning
These devices may only be installed, connected and operated by trained and qualified staff. Qualified staff must have knowledge of protection
classes, directives and regulations concerning electrical equipment designed for use in explosion hazardous areas.
Please verify that the classification and the marking on the device comply with the actual application conditions.
This device is only suited for connection to approved Exi circuits compliant to EN60079-0 and -11. Please observe the maximum admissible
electrical values.
After connection to other circuits the sensor may no longer be used in Exi installations. When interconnected to (associated) electrical equip-
ment, it is required to perform the "Proof of intrinsic safety" (EN60079-14).
Installation and mounting instructions
Avoid static charging of cables and plastic devices. Please only clean the device with a damp cloth. Do not install the device in a dust flow and
avoid build-up of dust deposits on the device.
If the devices and the cable could be subject to mechanical damage, they must be protected accordingly. They must also be shielded against
strong electro-magnetic fields.
The pin configuration and the electrical specifications can be taken from the device marking or the technical data sheet.
In order to avoid contamination of the device, please remove possible blanking plugs of the cable glands or connectors only shortly before in-
serting the cable or opening the cable socket.
service / maintenance
Repairs are not possible. The approval expires if the device is repaired or modified by a person other than the manufacturer. The most important
data from the approval are listed.