turck BL67 User manual

G1011
Revised 1/14/2014
HOW TO
How to Flash BL67/BL20 RFID
Using a Universal Programming
Dongle and Memtool 3

2www.turck.com • 1-800-544-7769 • Fax: [phone] • TURCK • Minneapolis, MN 55441 www.turck.com • 1-800-544-7769 • Fax: [phone] •TURCK • Minneapolis, MN 55441 3
MATERIALS LIST
BL 20 Materials Hardware list:
• 1) RS 232 cable
• 2) RS 232 to Universal Dongle converter
• 3) Universal Programming Dongle
• 4) Card Connector
• 5) 5V power supply
• 6) BL 67 cards your ashing
• 7) Soldering iron
• 8) Solder
• 9) Scalpel
• 10) Clamp
BL20 Material Software List:
• 1) Windows XP operating system
• 2) Memtool 3
• 3) Most recent version of the 2RFID-A or 2RFID-S rmware le
BL 67 Materials Hardware list:
• 1) RS 232 cable
• 2) RS 232 to Universal Dongle converter
• 3) Universal Programming Dongle
• 4) Card Connector
• 5) 5V power supply
• 6) BL 67 cards your ashing
BL67 Material Software List:
• 1) Windows XP operating system
• 2) Memtool 3
• 3) Most recent version of the 2RFID-A or 2RFID-S rmware le

www.turck.com • 1-800-544-7769 • Fax: [phone] •TURCK • Minneapolis, MN 55441 3
IMPORTANT NOTES:
1. The Universal Programming Dongle can ONLY handle 5 Volts. (Please do not burn up your dongle by putting too
much voltage through it.)
2. I’ve have only been able to ash using a Windows XP operating system. (It appears that my Windows 7 64 bit
operating system is to new of a computer perform ashing.)
SETUP THE STATION:
-> Hook the 1) RS232 cable to the back of your computer -> Hook the other end of the RS 232 cable to the 2) RS232 to
Universal Dongle converter -> Hook the converter to the 3) Universal Dongle itself -> Leave the 4) Card Connector alone
for the moment -> Hook the power leads up to the 5) Power Supply.

4www.turck.com • 1-800-544-7769 • Fax: [phone] • TURCK • Minneapolis, MN 55441 www.turck.com • 1-800-544-7769 • Fax: [phone] •TURCK • Minneapolis, MN 55441 5
If you are ashing a BL67 card, please skip to page six. If you’re ashing a BL20, please read on.
LET’S FLASH A BL20 CARD.
-> Remove the card from the casing
-> Bring the card to your solder station and nd pin 1 of the top right micro chip (Look at the pictures)

www.turck.com • 1-800-544-7769 • Fax: [phone] •TURCK • Minneapolis, MN 55441 5
-> Gently remove pin 1 using your soldering iron and scalpel
-> This is what your chip should look like once pin 1 is removed

6www.turck.com • 1-800-544-7769 • Fax: [phone] • TURCK • Minneapolis, MN 55441 www.turck.com • 1-800-544-7769 • Fax: [phone] •TURCK • Minneapolis, MN 55441 7
-> Bring the card back to your ashing station and hook it up to the Card Connecter (Note: If the Card Connecter is
touching the even connectors on the card it will not ash.)
SET UP THE UNIVERSAL PROGRAMMING DONGLE
-> Make sure the switch is to the right -> Hit reset before you begin programming in Memtool 3 (You also must hit the
reset switch before every card you program)

www.turck.com • 1-800-544-7769 • Fax: [phone] •TURCK • Minneapolis, MN 55441 7
-> Open Memtool 3
-> Open le -> Choose your rmware le -> Open

8www.turck.com • 1-800-544-7769 • Fax: [phone] • TURCK • Minneapolis, MN 55441 www.turck.com • 1-800-544-7769 • Fax: [phone] •TURCK • Minneapolis, MN 55441 9
-> Highlight the rmware le -> Connect
-> Add Set -> Program

www.turck.com • 1-800-544-7769 • Fax: [phone] •TURCK • Minneapolis, MN 55441 9
-> Let the program run
IMPORTANT NOTES:
1. When the programming has nished, remember to solder pin 1 back down. (BL20 users)
2. Every time you ash and new a new card you must hit the reset on the Universal Programming Dongle.
TROUBLE SHOOTING SOLUTIONS
-> If you get an error message in Memtool 3, here are some possible faults.
1. You forgot to hit the reset button on the Universal Programming Dongle. Hit the reset.
2. The Card Connecter is touching the even connections on the card. Readjust it.
3. You did a poor job unsoldering pin 1. Check your work and try it again.
4. You allowed the soldering iron to touch the microchip, which in turned burned up the card’s circuitry. Throw it away.
5. You didn’t set up the Universal Programming Dongle correctly. Recheck it.
6. You ran more than 5V through the dongle and the dongle burned up. Try a dierent one.
7. Maybe the card is bad to start. Check it in PACTware of Xion Tool.
8. If one card just won’t connect, try a dierent card.
IMPORTANT NOTE:
EVERY TIME YOU DO A TROUBLE SHOOTING SOLUTION YOU MUST COMPLETELY CLOSE OUT AND
RESTART MEMTOOL.