Tyco F08 FIP User manual

FIRE FIGHTER’S GUIDE
1. SILENCING BELLS
Press “SILENCE” key once.
- ALL flashing red “ALM” LEDs will go steady
- Local Bells will be silenced
- The internal sounder will be silenced if no fault
condition exists.
-Any new alarm will cause the bells to ring again
and the appropriate zone alarm LED to flash.
2. RESETTING ALL ZONES IN ALARM
Press “SELECT” key, if required, until all green “SEL” LEDs are
OFF, then press “RESET” key once.
- ALL flashing or steady red “ALM” LEDs turn OFF.
SILENCE
- Zone(s) still in alarm will be indicated again.
3. ISOLATING ALL ZONES IN ALARM
Press “SELECT” key, if required, until all green “SEL” LEDs are
OFF, then press “ISOLATE” key once.
RESET
- ALL flashing red “ALM” LED indicators will go steady
and amber “ISO” LEDs will turn ON.
-DE-ISOLATING ZONE WILL RE-ACTIVATE BELLS
4. ISOLATING SELECTED ALARM ZONE
Press “SELECT” key until the required zone’s green “SEL” LED
is ON, then press “ISOLATE” key once.
- Amber “ISO” LED will turn ON.
-IF A FALSE ALARM, CALL THE MAINTENANCE
COMPANY RESPONSIBLE FOR THE FIRE ALARM
SYSTEM.
ISOLATE
3. RING SILENCED BELLS
Press “SELECT” key until a ZONE IN ALARM is SELECTED.
(Green “SEL” LED is ON)
If amber “ISO” LED is ON, press “ISOLATE” key ONCE.
If amber “ISO” LED is OFF, press “ISOLATE” key TWICE.
- Amber “ISO” LED indicator will be OFF.
ISOLATE
SELECT
- Bells are operated.
ISOLATE
SELECT

THIS PAGE INTENTIONALLY LEFT BLANK

F08 FIP
OPERATOR’S MANUAL
F08 PRODUCT MANUAL
DOCUMENT: LT0054 (A5 Bound)
DOCUMENT: LT0080 (A4 Loose)
Issue 3.05; 24 March 2006
- A P P R O V A L S -
F08 PANEL APPROVALS TO AUSTRALIAN STANDARDS AS1603.4 1987 AMDT 1 & 2
SSL LISTING NUMBER afp380
The F08 Fire Indicator Panel is manufactured for
Tyco Services Fire & Safety
47 Gilby Road
Mt Waverley
VIC 3149
AUSTRALIA
Tel : [phone]
Fax : [phone]
COPYRIGHT I 1998, 2002
Information contained in this document is copyright, and shall not be reproduced in any form whatsoever,
or its contents disclosed to any third party, without the written consent of Tyco Services Fire & Safety (The
Company). Information contained in this document is believed to be accurate and reliable, however the
company reserves the right to change the content without prior notice.

F08 Operator's Manual Document No: LT0054
INSTALLATION DETAILS
3.W A R N I N G –
The F08 is approved to AS/NZS 3548 Class A. In a domestic environment it may cause
radio interference in which case the user may be required to take adequate measures.
For your reference please complete the following information on the F08 Fire Indicator Panel
supplied.
PANEL TYPE F08
PANEL SUPPLIED BY
PANEL SERIAL NUMBER
PANEL DATE OF MANUFACTURE
INSTALLED BY
AS INSTALLED DRAWING NUMBER ISSUE:
COMMISSIONED DATE
CONTRACT / JOB NUMBER
OWNER / ADDRESS
OWNERS REPRESENTATIVE
TELEPHONE B.H. A.H.
SERVICE COMPANY
SERVICE CONTACT
TELEPHONE B.H. A.H.
Page ii 24 March 2006 Issue 3.05

Document No: LT0054 F08 Operator's Manual
TABLE OF CONTENTS
INSTALLATION DETAILS ....................................................................................................ii
AMENDMENT LOG..............................................................................................................vi
1 SYSTEM DESCRIPTION.................................................................................................. 1-1
1.1 OVERVIEW....................................................................................................................1-2
1.2 DISPLAY PANEL .......................................................................................................... 1-4
1.3 COMMAND KEYS......................................................................................................... 1-7
2 SPECIFICATIONS............................................................................................................ 2-1
2.1 SYSTEM........................................................................................................................ 2-2
2.2 PHYSICAL..................................................................................................................... 2-3
2.3 ELECTRICAL ................................................................................................................ 2-4
2.4 INDICATORS................................................................................................................. 2-4
2.5 SWITCHES....................................................................................................................2-4
3 INTERPRETING THE DISPLAYS.................................................................................... 3-1
3.1 SYSTEM NORMAL ....................................................................................................... 3-2
3.2 RESPONDING TO ALARMS ........................................................................................ 3-2
3.3 DEALING WITH FAULTS ............................................................................................. 3-3
3.4 ZONE INDICATIONS..................................................................................................... 3-4
3.5 SYSTEM STATUS INDICATORS ................................................................................. 3-5
3.6 OUTPUT INDICATORS................................................................................................. 3-6
4 BRIGADE OPERATING FUNCTIONS............................................................................. 4-1
4.1 RESETTING ZONE(S) IN ALARM OR FAULT............................................................. 4-2
4.2 SILENCING ZONE(S) IN ALARM OR FAULT.............................................................. 4-3
4.3 ISOLATING ZONE(S) IN ALARM................................................................................. 4-4
5 SYSTEM OPERATING FUNCTIONS............................................................................... 5-1
5.1 SYSTEM TEST.............................................................................................................. 5-2
5.2 BATTERY TEST............................................................................................................ 5-3
5.3 OUTPUT ISOLATE/DE-ISOLATE................................................................................. 5-4
Issue 3.05 24 March 2006 Page iii

F08 Operator's Manual Document No: LT0054
5.4 ANCILLARY RELAY FAULT RESET ........................................................................... 5-5
5.5 OUTPUT TEST & MAPPING DISPLAY........................................................................ 5-6
6 ZONE OPERATING FUNCTIONS.................................................................................... 6-1
6.1 ZONE TEST...................................................................................................................6-2
6.2 ZONE ISOLATE/DE-ISOLATE...................................................................................... 6-4
6.3 AUTO-RESET MODE (One Person Detector-in-Situ Test)...................................... 6-5
7 PLACING INTO OPERATION.......................................................................................... 7-1
7.1 GENERAL .....................................................................................................................7-2
7.2 MAINS ISOLATE SWITCH............................................................................................ 7-2
7.3 POWER UP ................................................................................................................... 7-3
7.4 COMMISSIONING CHECKLIST ................................................................................... 7-3
8 SYSTEM MAINTENANCE & TROUBLE-SHOOTING ..................................................... 8-1
8.1 SYSTEM MAINTENANCE............................................................................................. 8-2
8.2 TROUBLE-SHOOTING ................................................................................................. 8-3
APPENDIX A – COMPATIBLE ACTUATING DEVICES….………………………………..... A-1
APPENDIX B – COMPATIBLE BATTERIES……………….…………………………………..
A-3
APPENDIX C – SYSTEM CONFIGURATION……………………………………………… ...A-4
Page iv 24 March 2006 Issue 3.05

Document No: LT0054 F08 Operator's Manual
AMENDMENT LOG
ISSUE DATE AMENDMENT ECN
2 04/05/92 Revised and upgraded from Document 696-002 (Issue
1 Amdt 1) to VIGILANT Document LT0054.
2.0 27/05/98 Converted to WORD format.
3.0 27/10/98 Modified for V3.00 software, 15V MCP and M614
detectors. New circuit delay types added.
Programmable mode for zone open collector outputs to
override zone isolate. 5 second reset time for new
M614 detector types.
2769
3.01 03/12/98 Appendix A Approved Detectors Revised. ECS543
3.02 31/07/02 Prefix and Appendix A revised 3322
3.03 01/03/05 Appendix A – added 614CH, 614I & 614P 3635
3.04 28/10/05 Appendix A – added System Sensor detector 885WP-B ECS1181
3.05 24/03/06 Appendix A – added 614T 3731
Issue 3.05 24 March 2006 Page v

F08 Operator's Manual Document No: LT0054
THIS PAGE LEFT INTENTIONALLY BLANK
Page vi 24 March 2006 Issue 3.05

Document No: LT0054 F08 Operator's Manual
System Description
1 SYSTEM DESCRIPTION
Issue 3.05 24 March 2006 Page 1-1

F08 Operator's Manual Document No: LT0054
System Description
1.1 OVERVIEW
The F08 Fire Indicator Panel (FIP) is a compact, self-contained fire indicator panel, which
performs the functions of the Control and Indicating Equipment (CIE), as specified by the
Australian Standard AS1603.4 Automatic Fire Detection and Alarm Systems.
It is microprocessor based and provides a maximum of eight detection zones using
approved compatible actuating devices. A general view of the F08 Fire Indicator Panel,
illustrating its various components, is shown in Figure 1.1.
The fire alarm system consists of fire detectors and/or manual call points installed in various
locations throughout the building, or area to be protected, linked to the F08 FIP.
When any detector or manual call point is operated, a signal is received by the FIP. The F08
panel reacts to the alarm condition as programmed, and may provide visual and audible
indications. Other signals to remote functions may also be generated. Examples include:
a) Mechanical ventilation plant shutdown
b) Local Alarm
c) Alarm to Fire Control Station.
The F08 fire indicating panel consists of:
a) A Wall-Mounting Cabinet
b) One Processor Main board, including Power Supply/Charger
c) One Display/Control Board.
The panel is a standard part that can be interchanged in the field. The door of the panel
contains display electronics and controls, whilst the rear of the cabinet contains processing
electronics, and input and output terminals.
The F08 FIP provides a range of programmable options. These are: disable unused circuits;
latching or non-latching circuits; ten types of circuit timing delays, including AVF and 1668
control; 'mapping' of zones to outputs; and ancillary output supervision.
NOTE: If your requirements have changed, the F08 FIP will require reprogramming,
so please consult your installation or service company.
The following F08 product manuals are available:
Volume 1, F08 Operator’s Manual, provides a complete guide to the operation, and
maintenance of the F08 Fire Indicator Panel, according to Australian Standards AS1603 Part
4. This manual is provided as standard with the F08 FIP. Part Numbers are LT0080 in A4
size, or LT0054 in A5, that will fit inside the F08 FIP.
Volume 2, F08 Technical Manual, provides complete technical details on the F08 system
and components, according to Australian Standards AS1603 Part 4, for servicing purposes.
Part Number is LT0081.
Volume 3, F08 Installation Manual, provides complete installation and programming
instructions for the F08 system. Part Number is LT0082.
Page 1-2 24 March 2006 Issue 3.05