Tyco K17-231 User manual

Model K17-231 — 16.8 K-factor
Upright and Pendent Sprinklers
Standard Response, Standard Coverage
Page 1 of 4 SEPTEMBER 2014 TFP332
IMPORTANT
Always refer to Technical Data
Sheet TFP700 for the “INSTALLER
WARNING” that provides cautions
with respect to handling and instal-
lation of sprinkler systems and com-
ponents. Improper handling and in-
stallation can permanently damage
a sprinkler system or its compo-
nents and cause the sprinkler to fail
to operate in a fire situation or cause
it to operate prematurely.
Worldwide
Contacts
www.tyco-fire.com
NOTICE
The 16.8 K-factor, Model K17-231 Up-
right and Pendent Sprinklers described
herein must be installed and maintained
in compliance with this document and
with the applicable standards of the Na-
tional Fire Protection Association, in ad-
dition to the standards of any authori-
ties having jurisdiction. Failure to do so
may impair the performance of these
devices.
The owner is responsible for main-
taining their fire protection system
and devices in proper operating con-
dition. Contact the installing contrac-
tor or product manufacturer with any
questions.
Sprinkler
Identification
Number (SIN)
TY7151 – Upright, 16.8K
TY7251 – Pendent, 16.8K
TY7151 is a redesignation for C7151,
G1888, and S8040.
TY7251 is a redesignation for C7251,
G1889, and S8041
Technical
Data
Approvals
UL and C-UL Listed. FM and NYC Ap-
proved. (Specic details for laboratory
listings and approvals given in Table A.
The approvals apply to the service con-
ditions indicated in the Design Criteria
section.)
Maximum Working Pressure
175 psi (12,1 bar)
Pipe Thread Connection
3/4 inch NPT
Discharge Coefficient
K = 16.8 gpm/psi1/2
(241,9 lpm/bar1/2)
General
Description
The TYCO 16.8 K-factor, Model
K17-231, Standard Response, Standard
Coverage, Upright and Pendent Sprin-
klers (Ref. Figure 1) are automatic sprin-
klers of the frangible bulb type. They
are “standard response spray sprin-
klers” which produce a hemispherical
water distribution pattern below the
deector.
The 16.8 K-factor, K17-231 Sprinklers
were subjected to full scale, high-piled
storage, re tests to qualify their use
in lieu of 8.0 or 11.2 K-Factor standard
spray sprinklers for the protection of
high-piled storage.
Higher ow rates can be achieved at
much lower pressures with the 16.8 K-
factor, K17-231 Sprinklers — making
their use highly advantageous in high
density applications, such as the pro-
tection of high-piled storage.
Applications for the 16.8 K-factor, Mod-
el K17-231 Pendent and Upright Sprin-
klers are expanding beyond the cur-
rent listings/approvals. For information
regarding research re tests which may
be acceptable to an authority having ju-
risdiction, please contact the Technical
Services Department.
Temperature Ratings
Refer to Table A.
Finish
Natural Brass
Physical Characteristics
Frame ................... Bronze
Button................... Bronze
Sealing Assembly. . . . . . . . .Beryllium
Nickel w/TEFLON
Bulb (5 mm) . . . . . . . . . . . . . . . .Glass
Compression Screw. . . . . . . . . Brass
Deector.................. Brass

TFP332
Page 2 of 4
Design
Criteria
UL and C-UL Listing Requirements
The TYCO 16.8 K-factor, Model K17-231
(TY7151 & TY7251) Sprinklers may be
installed in accordance with NFPA 13
standard sprinkler position and area/
density ow calculation requirements
for light, ordinary, or extra hazard oc-
cupancies with a minimum residual
(owing) pressure of 7 psi (0,5 bar) in
wet or dry pipe sprinkler systems, or
they may be installed in accordance
with NFPA 13 standard sprinkler posi-
tion and area/density ow calculation
requirements for high piled storage oc-
cupancies (solid piled, palletized, rack
storage, bin box, and shelf storage in-
cluding but not limited to Class I-IV and
Group A plastics) with a minimum resid-
ual (owing) pressure of 7 psi (0,5 bar)
for wet or dry pipe systems.
The following two examples are typical
of the types of arrangements permit-
ted by NFPA 13. For all combinations
of lesser and greater building heights,
lesser and greater storage heights,
storage arrangements, commodity
classications, and lesser or greater re-
quired design densities, refer to NFPA
13 for specics.
Example 1: NFPA 13 provides ceiling
only protection (that is, no in-rack sprin-
klers) criteria using open frame (that is,
no solid shelves) single, double, multi-
ple-row, or portable rack storage (with-
out the need for in-rack sprinkler pro-
tection) of cartoned unexpanded Group
A or B plastics, or, cartoned expanded
Group A or B plastics, with:
• a storage height of up to 20 feet
(6,1 m);
• a maximum ceiling height of 27 feet
(8,2 m);
• a minimum deector to top of
storage clearance of 18 inches
(457 mm);
• a minimum design density of 0.60
gpm/ft2(24,4 mm/min);
• a minimum residual (owing)
pressure of 7 psi (0,5 bar);
• a minimum design area of 2000 ft2
(186 m2) for wet systems or 2600 ft2
(242 m2) for dry pipe systems
Example 2: NFPA 13 provides ceiling
only protection (that is, no in-rack sprin-
klers) criteria using open frame (that is,
no solid shelves) single, double, multi-
ple-row, or portable rack storage (with-
out the need for in-rack sprinkler pro-
tection) of cartoned unexpanded Group
A or B plastics, or, cartoned expanded
Group A or B plastics, with:
• a storage height of up to 25 feet
( 7, 6 m);
• a maximum ceiling height of 30 feet
(9,1 m);
• a minimum deector to top of
storage clearance of 18 inches
(457 mm);
• a minimum design density of
0.80 gpm/ft2(32,6 mm/min);
• a minimum residual (owing)
pressure of 7 psi (0,5 bar);
• a minimum design area of 2000 ft2
(186 m2) for wet systems or 4500 ft2
(418 m2) for dry pipe systems
FM Approval Requirements
The TYCO 16.8 K-factor, Model K17-231
(TY7151) Upright Sprinklers may be in-
stalled in accordance with the applica-
ble control mode density/area guide-
lines provided by Factory Mutual. (FM
guidelines may differ from UL and C-UL
Listing criteria.)
TYPE TEMPERATURE BULB
LIQUID
SPRINKLER FINISH
NATURAL BRASS
UPRIGHT
K=16.8 (TY7151)
155°F (68°C) Red
1, 2, 3, 4200°F (93°C) Green
286°F (141°C) Blue
PENDENT
K=16.8 (TY7251)
155°F (68°C) Red
1, 2, 4200°F (93°C) Green
286°F (141°C) Blue
NOTES:
(1) Listed by Underwriters Laboratories, Inc. (UL Listed).
(2) Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL Listed).
(3) Approved by Factory Mutual Research Corporation (FM Approved).
(4) Approved by the City of New York under MEA 177-03-E.
TABLE A
LABORATORY LISTINGS AND APPROVALS
(Refer To The Design Criteria Section)

TFP332
Page 3 of 4
Operation
The glass bulb contains a uid that ex-
pands when exposed to heat. When the
rated temperature is reached, the uid
expands sufciently to shatter the glass
bulb, allowing the sprinkler to activate
and ow water.
Installation
The TYCO Model K17-231 Sprinklers
must be installed in accordance with
this section.
General Instructions
Do not install any bulb type sprinkler if
the bulb is cracked or there is a loss
of liquid from the bulb. With the sprin-
kler held horizontal, a small air bubble
should be present. The diameter of the
air bubble is approximately 1/16 inch
(1,6 mm).
Step 1. With pipe thread sealant ap-
plied to the pipe threads, hand tighten
the Model K17-231 Sprinkler into the
sprinkler tting.
Step 2. Using the W-Type 8 Sprin-
kler Wrench (Ref. Fig. 2) applied to the
sprinkler Wrench Flats (Ref. Fig. 1),
tighten the Model K17-231 Sprinkler into
the sprinkler tting.
NOTICE
A leak tight 3/4 inch NPT sprinkler joint
should be obtained with a torque of 10
to 20 ft.lbs. (13,4 to 26,8 Nm). Higher
levels of torque may distort the sprin-
kler inlet with consequent leakage or
impairment of the sprinkler.
Care and
Maintenance
The TYCO Ultra K17 Sprinklers must be
maintained and serviced in accordance
with this section.
Before closing a re protection system
main control valve for maintenance
work on the re protection system that
it controls, permission to shut down the
affected re protection systems must
be obtained from the proper authorities
and all personnel who may be affected
by this action must be notied.
Sprinklers that are found to be leaking
or exhibiting visible signs of corrosion
must be replaced.
Automatic sprinklers must never be
painted, plated, coated, or otherwise
altered after leaving the factory. Modi-
ed sprinklers must be replaced. Sprin-
klers that have been exposed to corro-
sive products of combustion, but have
not operated, should be replaced if
they cannot be completely cleaned by
wiping the sprinkler with a cloth or by
brushing it with a soft bristle brush.
Care must be exercised to avoid dam-
age to the sprinklers before, during, and
after installation. Sprinklers damaged
by dropping, striking, wrench twist/
slippage, or the like, must be replaced.
Also, replace any sprinkler that has a
cracked bulb or that has lost liquid from
its bulb. (Ref. Installation Section).
The owner is responsible for the in-
spection, testing, and maintenance of
their re protection system and devices
in compliance with this document, as
well as with the applicable standards
of the National Fire Protection Asso-
ciation (e.g., NFPA 25), in addition to
the standards of any other authorities
having jurisdiction. Contact the install-
ing contractor or product manufacturer
with any questions.
Automatic sprinkler systems are recom-
mended to be inspected, tested, and
maintained by a qualied Inspection
Service in accordance with local re-
quirements and/or national codes.
*
*
*
UPRIGHT PENDENTCROSS SECTION
1
2
3
4
5
6
-
2
Button
Compression
Screw
Bulb
Sealing Assembly
-
6
-
4
5
-
3
-
Frame
1
-
Deector 2-3/8"
(60,3 mm)
WRENCH
FLAT
Temperature rating is
indicated on deector.
1/2"
(12,7 mm)
NOMINAL
MAKE-IN
3/4"
NPT
WRENCH
RECESS
FIGURE 1
MODEL K17-231 UPRIGHT (TY7151) AND PENDENT (TY7251) SPRINKLERS
FIGURE 2
W-TYPE 8
SPRINKLER WRENCH

GLOBAL HEADQUARTERS | 1400 Pennbrook Parkway, Lansdale, PA 19446 | Telephone [phone]
TFP332
Page 4 of 4
Copyright © 2014 Tyco Fire Products, LP. All rights reserved.
TEFLON is trademark of The DuPont Corporation
Limited
Warranty
For warranty terms and conditions, visit
www.tyco-re.com
Ordering
Procedure
Contact your local distributor for avail-
ability. When placing an order, indicate
the full product name and Part Num-
ber (P/N).
Sprinkler Assemblies with NPT
Thread Connections
Specify: (specify SIN), 16.8 K-factor,
Model K17-231, (specify) temperature
rating, (specify Pendent or Upright)
Sprinkler, P/N (specify):
Upright (SIN TY7151)
155°F (68°C) .......... P/N 51-888-1-155
200°F (93°C) ..........P/N 51-888-1-200
286°F (141°C) .........P/N 51-888-1-286
Pendent (SIN TY7251)
155°F (68°C) .......... P/N 51-889-1-155
200°F (93°C) ..........P/N 51-889-1-200
286°F (141°C) .........P/N 51-889-1-286
Sprinkler Wrench
Specify: W-Type 8 Sprinkler Wrench,
P/N 56-892-1-001