Ubiquiti NanoStation M2 User manual

2021-06-18 08:10 1/2 Anleitung – Unbrick Nanostation
Netz39 - https://www.netz39.de/wiki/
Anleitung – Unbrick Nanostation
Manual for Unbrick a UBNT Nanostation
compatible for:
Nanostation M2
Nanostation M2 XW
Nanostation loco M2
Nanostation loco M2 XW
Nanostation M5
Nanostation M5 XW
Nanostation loco M5
Nanostation loco M5 XW
(1) Download the AirOS 5.5.x firmware executable from the Ubiquiti website. Choose XM or XW
version depending on your device, If you don’t know, take a guess!
XM.v5.5.11.28002.150723.1344.bin, changelog
for: AG-HP-2G16, AG-HP-5G23, AG-HP-5G27, AirGrid M2, AirGrid M5, AR, AR-HP, BM2HP,
BM2-Ti, BM5HP, BM5-Ti, LiteStation M5, locoM2, locoM5, locoM9, M2, M3, M365, M5,
M900, NB-2G18, NB-5G25, NBM3, NBM365, NBM9, NS2, NSM3, NSM365, NSM5, PBM10,
PBM3, PBM5, Power AP N
XW.v5.5.10-u2.28005.150723.1358.bin, changelog
for: AG-HP-2G16, AG-HP-2G20, AG-HP-5G23, AG-HP-5G27, AirGrid M, AirGrid M2, AirGrid
M5, locoM2, locoM5, locoM9, M2, M3, M365, M5, M900, NBE-M2-13, NBE-M5-16, NBE-
M5-19, NSM2, NSM3, NSM365, NSM5, PBM3, PBM365, PBM5, RM2-Ti, RM5-Ti
(2) Start device into config/maintenance mode: in this precise order, unpower device,
configure PC into static IP 192.168.1.3 Netmask 255.255.255.0
press and maintain reset button
plug device in, release reset button as soon as LEDs blink (please wait 20-30 seconds)
(note 1: LED blink pattern is different depending on device: Sometimes a single LED blinking 3/4
on, 1/4 off, sometimes two LEDs blinking "sideways")
(note 2: the static-IP connection to the device must be established before it boots into config
mode. It was tricky rebooting the device fast enough that the PC connection did not go down.
YMMV.)
(3) TFTP the AirOS 5.5.x firmware into the device:
tftp 192.168.1.20
(note: use this IP regardless of what firmware is already on the device)

Last update: 2018-01-25 22:30 freifunk:anleitungen:unbricknanostation https://www.netz39.de/wiki/freifunk:anleitungen:unbricknanostation
https://www.netz39.de/wiki/ Printed on 2021-06-18 08:10
tftp > bin
tftp > put complicatedfirmwarefilename.bin flash_upgrade
(note 1: this should only last 3 or 4 seconds, if not, you've done something wrong)
(note 2: it's possible that the device checks whether the firmware is version XW/XM at this point, and
refuse to load an incorrect firmware)
tftp > quit
(4) wait approx 10 minutes for the device to reboot (note: don’t try to be too smart, and be patient!)
(5) At this point the AirOS firmware is loaded, but the old settings are still in place. Here I was only
able to connect to the device via 192.168.1.1 with read-only credentials. To reset the settings (bu not
the firmware), when the device has already booted, press the reset button until LEDs blink, without
ever unplugging it.
(6) Now finally we have a factory-setting M5. It gives us an IP in DHCP, and the interface is at
192.168.1.20, login ubnt/ubnt
(7) And navigating in the admin interface, we can upload the Freifunk firmware for the M5, which we
download from https://md.freifunk.net/mitmachen/firmware/
(8) Upon reboot, the device (now on gluon firmware) starts in config mode and with the same static IP
set-up as before, we can access the set-up screen at http://192.168.1.1/ .
From now on, config mode is simply accessed by pressing reset button 5 seconds or so. There is no
need to reboot the device.
(9) Finally, do yourself/a future owner a favor: take a sharpie marker, and write down the type of
hardware (XW or XM) on the device itself!
further information: UniFi - TFTP soft recovery for bricked access point
→ zurück zu den Anleitungen
CC BY-SA 4.0 2016 Freifunk Magdeburg
From:
https://www.netz39.de/wiki/ - Netz39
Permanent link:
https://www.netz39.de/wiki/freifunk:anleitungen:unbricknanostation
Last update: 2018-01-25 22:30