Ubiquiti LTU-Lite User manual

LTU-Lite Wall Mount Bracket Screws (Qty. 2)
Screw Anchors (Qty. 2) Zip Tie Gigabit PoE (24V, 0.5A) with
Mounting Bracket
Power Cord
Package Contents
Installation Requirements
LTU PtMP AP, such as model LTU-Rocket
Phillips screwdriver for wall-mounting
Outdoor, shielded Category 6 (or above) cabling and shielded RJ45 connectors are
required for all wired Ethernet connections.
LTU-Lite Quick Start Guide

System LED
Surge protection should be used for all outdoor installations. We recommend that you
use two Ethernet Surge Protectors, model ETH-SP-G2, one near the device and the other
at the entry point to the building. The ETH-SP-G2 will absorb power surges and safely
discharge them into the ground.
Hardware Overview
Note: For guidelines about grounding and lightning protection, follow your
local electrical regulatory codes.
LTU-Lite Quick Start Guide

Ethernet Port
Reset Button
Blue Initial power-up.
Flashing White Bootup in progress.
White Ready for use.
Alternating
Blue/White Firmware upgrade in progress.
This 10/100/1000 Ethernet port is used to connect the power and should be connected
to the LAN and DHCP server.
To reset to factory defaults, press and hold the Reset button for more than 10 seconds
while the device is powered on.
Hardware Installation
1.
2.
LTU-Lite Quick Start Guide

3.
Wall Mount
1.
LTU-Lite Quick Start Guide

2.
LTU-Lite Quick Start Guide

3.
LTU-Lite Quick Start Guide

4.
LTU-Lite Quick Start Guide

5.
LTU-Lite Quick Start Guide

Pole Mount
1.
LTU-Lite Quick Start Guide

2.
LTU-Lite Quick Start Guide

3.
LTU-Lite Quick Start Guide

Connecting Power
WARNING: The switch port must comply with the power specifications listed in
“Specifications” .
LTU-Lite Quick Start Guide

OR
Optional
Accessing the Configuration Interface
1. Make sure that your host system is connected via Ethernet to the device.
2. Configure the Ethernet adapter on your host system with a static IP address on the
192.168.1.x subnet.
3. Launch your web browser and type https://192.168.1.20 in the address field. Press enter
(PC) or return (Mac).
LTU-Lite Quick Start Guide

4. Select your Country and Language. You must agree to the Terms of Use to use the
product. Click Continue.
The LTU Configuration Interface will appear, allowing you to customize your settings as
needed.
UISP Management
You can manage your device using UISP, which lets you configure, monitor, upgrade, and
back up your devices using a single application. Get started at uisp.ui.com
Find My AP
1. Click the icon.
2. In the Wireless Settings section, change the channel bandwidth (default: 20 MHz) as
needed.
3. Click Find AP.
4. The device will scan for nearby APs. Click Select for the appropriate AP. To run the search
again, click Scan.
5. Follow the on-screen instructions.
Installer Compliance Responsibility
Devices must be professionally installed and it is the professional installer’s responsibility
to make sure the device is operated within local country regulatory requirements.
The Auto Output Power field is provided to the professional installer to assist in meeting
regulatory requirements.
Specifications
LTU-Lite
Dimensions 153 x 84 x 39.5 mm
(6.02 x 3.31 x 1.56")
Weight 250 g (8.82 oz)
Networking Interface (1) 10/100/1000 Ethernet Port
Enclosure Outdoor UV Stabilized Plastic
Note: For example, if the AP’s channel bandwidth is set to 50 MHz and your
device is set to 20 MHz, then your device will not see that AP and you should
change the channel bandwidth on your device.
LTU-Lite Quick Start Guide

LTU-Lite
Max. Power Consumption 8.5W
Power Supply 24V, 0.5A Gigabit PoE Adapter (Included)
Power Method Passive PoE 2-Pair (Pairs 4, 5+; 7, 8-)
Supported Voltage Range 22 - 26V
Gain 13 dBi
Mounting Pole Mount
Wall Mount (Kit Included)
Wind Survivability 200 km/h (125 mph)
Wind Loading 20 N @ 200 km/h
(4.5 lbf @ 125 mph)
ESD/EMP Protection ± 24kV Contact / Air
Operating Temperature -40 to 60° C (-40 to 140° F)
Operating Humidity 5 to 95% Noncondensing
Certifications CE, FCC, IC
Operating Frequency (MHz)
Worldwide 4800 - 6200*
US/CA U-NII-1 5150 - 5250
U-NII-2A 5250 - 5350
U-NII-2C 5470 - 5725
U-NII-3 5725 - 5850
* Depends on regulatory region.
Bluetooth LE Management Radio (MHz)
Worldwide 2400 - 2483.5
Safety Notices
1. Read, follow, and keep these instructions.
2. Heed all warnings.
3. Only use attachments/accessories specified by the manufacturer.
WARNING: Do not use this product in location that can be submerged by water.
WARNING: Avoid using this product during an electrical storm. There may be a remote risk of
electric shock from lightning.
LTU-Lite Quick Start Guide

Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current requirements indicated on
the manufacturer’s label. Connection to a different power source than those specified may result in
improper operation, damage to the equipment or pose a fire hazard if the limitations are not
followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided only by a
qualified service technician.
3. This equipment is provided with a detachable power cord which has an integral safety ground wire
intended for connection to a grounded safety outlet.
a. Do not substitute the power cord with one that is not the provided approved type. Never use an
adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the grounding
wire.
b. The equipment requires the use of the ground wire as a part of the safety certification,
modification or misuse can provide a shock hazard that can result in serious injury or death.
c. Contact a qualified electrician or the manufacturer if there are questions about the installation
prior to connecting the equipment.
d. Protective earthing is provided by Listed AC adapter. Building installation shall provide
appropriate short-circuit backup protection.
e. Protective bonding must be installed in accordance with local national wiring rules and
regulations.
Limited Warranty
ui.com/support/warranty
The limited warranty requires the use of arbitration to resolve disputes on an individual basis, and,
where applicable, specify arbitration instead of jury trials or class actions.
Compliance
FCC
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions.
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
LTU-Lite Quick Start Guide

accordance with the instruction manual, may cause harmful interference to radio communications.
Operations of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
This radio transmitter has been approved by FCC.
ISED Canada
CAN ICES-3(A)/NMB-3(A)
This device complies with ISED Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
This radio transmitter has been approved by ISED Canada.
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for
harmful interference to co-channel mobile satellite systems.
CAN ICES-3(A)/NMB-3(A)
Le présent appareil est conforme aux CNR d’ISDE Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux conditions suivantes :
1. l’appareil ne doit pas produire de brouillage;
2. l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
Le présent émetteur radio a été approuvé par ISDE Canada.
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites
mobiles utilisant les mêmes canaux.
IMPORTANT NOTE
Radiation Exposure Statement
This equipment complies with radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 24 cm between the
radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
AVIS IMPORTANT
Déclaration sur l’exposition aux rayonnements
Cet équipement est conforme aux limites prévues pour l’exposition aux rayonnements dans un
environnement non contrôlé.
LTU-Lite Quick Start Guide

Lors de l’installation et de la mise en fonctionnement de l’équipement, assurez-vous qu’il y ait une
distance minimale de 24 cm entre l’élément rayonnant et vous.
Cet émetteur ne doit être installé à proximité d’aucune autre antenne ni d’aucun autre émetteur, et
ne doit être utilisé conjointement à aucun autre de ces appareils.
Australia and New Zealand
Warning: This equipment is compliant with Class A of CISPR 32. In a residential environment
this equipment may cause radio interference.
Brazil
Nota: Este equipamento não tem direito à proteção contra interferência prejudicial e não
pode causar interferência em sistemas devidamente autorizados.
CE Marking
CE marking on this product represents the product is in compliance with all directives that are
applicable to it.
Country List
AT BE BG CY CZ DE DK EE EL ES FI FR HR HU
IE IT LV LT LU MT NL PL PT RO SE SI SK UK
BFWA (Broadband Fixed Wireless Access) members noted in blue
Note: This device meets Max. TX power limit per ETSI regulations.
The following apply to products that operate in the 5 GHz frequency range:
Note: This device is restricted to indoor use only when operating in the 5150 - 5350 MHz
frequency range within all member states.
Note: Operation in the 5.8 GHz frequency band is prohibited in BFWA member states. Other
countries listed may use the 5.8 GHz frequency band.
WEEE Compliance Statement
Declaration of Conformity
LTU-Lite Quick Start Guide

Online Resources
© 2022 Ubiquiti Inc. All rights reserved.
LTU-Lite Quick Start Guide