Ubiquiti NB?2G18 User manual

Installation Guide
NanoBridge M2
Welcome
Thank you for purchasing your Ubiquiti NanoBridge.
This installation guide is for model NB-2G18.
Tools Required for Mounting
10mm wrench (Qty. 1)
Support
Internet: www.ubnt.com
Internet Support Forum: www.forum.ubnt.com
Ubiquiti support engineers are located in the U.S. and in Europe and are
dedicated to helping customers resolve software, hardware compatibility,
or eld issues as quickly as possible.
A
D
CB
F G H I J
B
C
D
E
F
G
M6 U-Bolt
M6X12 Carriage Bolt Bushing
2
4
I
J1
M6 Bolt-Springlock-Washer Assembly
H4
M6 Serrated Flange Nut 8
E
A
Contents Qty.
Parabolic Reector/Dish Pole Bracket Clamp 1
1
1
1
2
Dish Bracket
Antenna Feed
Feed Support
General Warranty:
UBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”) represents and warrants that the Products furnished hereunder shall be free from defects in material and workmanship for a period of one (1) year from the date of shipment by UBIQUITI NETWORKS
under normal use and operation. UBIQUITI NETWORKS sole and exclusive obligation under the foregoing warranty shall be to repair or replace, at its option, any defective Product that fails during the warranty period. The expense of removal and
reinstallation of any item is not included in this warranty.
and performance of the Products. UBIQUITI NETWORKS reserves the right to inspect all defective Products (which must be returned by Buyer to UBIQUITI NETWORKS factory freight prepaid).
No Products will be accepted for replacement or repair without obtaining a Return Materials Authorization (RMA) number from UBIQUITI NETWORKS. Products returned without an RMA number will not be processed and will be returned to Buyer freight
collect. UBIQUITI NETWORKS shall have no obligation to make repairs or replacement necessitated by catastrophe, fault, negligence, misuse, abuse, or accident by Buyer, Buyer’s customers or any other parties. The warranty period of any repaired or
replaced. Product shall not extend beyond its original term.
Warranty Conditions
The foregoing warranty shall apply only if:
(I) The Product has not been subjected to misuse, neglect or unusual physical, electrical or electromagnetic stress, or some other type of accident.
(II) No modication, alteration or addition has been made to the Product by persons other than UBIQUITI NETWORKS or UBIQUITI NETWORKS’s authorized representatives or otherwise approved by UBIQUITI NETWORKS.
(III) The Product has been properly installed and used at all times in accordance, and in all material respects, with the applicable Product documentation.
Disclaimer. UBIQUITI NETWORKS does not warrant that the operation of the products is error-free or that operation will be uninterrupted. In no event shall UBIQUITI NETWORKS be responsible for damages or claims of any nature or description relating to
system performance, including coverage, buyer’s selection of products for buyer’s application and/or failure of products to meet government or regulatory requirements.
Returns
In the unlikely event a defect occurs in this product, please work through the dealer or distributor from which this product was purchased.
* Products may be different from pictures and are subject to change without prior notice

6. Attach Antenna to Mounting Pole
6
5
5. Install Bushing to Feed Support
2
1. Install Feed Support to Dish Bracket
Install Feed Support to Dish Bracket by:
M6 Bolt-Springlock-Washer Assembly (Qty. 4)
Route network cable through the bottom hole of the Feed Support
and attach to the RJ-45 slot on the back of the Antenna Feed.
Insert Antenna Feed into Feed Support as the orientation shown
in the picture.
Mounting bracket can accommodate 1.25"-2.2" pole.
Attach antenna assembly to pole by:
M6 U-Bolt (Qty. 2)
Pole Bracket Clamp (Qty. 2)
M6 Serrated Flange Nut (Qty. 4)
Wrap network cable with the Bushing and then slide it into the hole
in the Feed Support.
C
Install Dish Bracket to Dish by:
M6X12 Carriage Bolt (Qty. 4)
M6 Serrated Flange Nut (Qty. 4)
D
C
B
C
C
J
B
A
D
2. Install Dish Bracket to Dish
1
3.Connect Network Cable to Antenna Feed
3
H
G
I
F
E
I
4
4. Install Antenna Feed
CH D
D
I
G
A
B
B
JC
C
C
FEI