Uplift Desk 99.039.14.0050-V4 Operating instructions

KEYPAD LOCK
The keypad can be locked to prevent accidental activation or movement of the desk.
To lock: Press and hold “M” button until display changes to “LOC”
To unlock: Press and hold “M” button until display changes to numeric height setting.
NOTE: If a power outage occurs, the program will automatically return to the unlocked setting.
These UPLIFT Desk programming instructions are compatible only with the Advanced 1-Touch
Digital Memory Keypad and control boxes with the following numbers located on the silver sticker:
PROGRAMMING YOUR UPLIFT DESK
CONSTANT-TOUCH & ONE-TOUCH
These steps allow the desktop to be set to either One-Touch or Constant-Touch. One-Touch requires
only a single touch of the “1, 2, 3, or 4” button to move the desktop to a preset memory location (One-
Touch is the default setting for 2-leg frames). Constant-Touch requires a continuous touch of the “1, 2,
3, or 4” button to move the desktop to a preset memory location (Constant-Touch is the default set-
ting for 3-leg and 4-leg frames).
Change between One-Touch and Constant-Touch:
l. Press the DOWN button until the desk reaches the lowest position.
 2. PresstheDOWNbuttonagainuntildisplayashes“RST”.
3. Press the “1” button until display shows “10.1” (One-Touch) or “10.2” (Constant-Touch)
  andgoesbackto“RST”.
Note:While“RST”isstillashing,youcanpressthe“1”buttonasmanytimesasyou’dlike
to toggle between the two settings.
4. Press the DOWN button until the desktop lowers slightly, then rises slightly and the display
changes back to the numeric height setting.
MEMORY SETTINGS
Saveuptofourcommonlyuseddeskheightsandrecallthemquickly.
l. Press the UP or DOWN button to move the desk to the desired height.
2. Press the “M” button.
3. Press the “1, 2, 3, or 4” button to assign the current height to a number on the keypad.
4. To recall any of those heights, press the numbered button to bring desk to assigned height.
HEIGHT CALIBRATION
Make sure the numeric display matches the actual height of the desktop in its lowest position.
1. Press the DOWN button until the desk reaches the lowest position.
 2. Measuretheheightfromtheoortotheundersideofthedesktop.Ifthedisplayedheight
does not match your measurement, follow the next steps.
 3. PresstheDOWNbuttonuntildisplayashes“RST”.
 4. Pressthe“M”buttonuntilthenumericdisplaybeginsashing.
5. Press the UP or DOWN button to set desk to the measured height.
 6. Oncedisplaychangesbackto“RST”,presstheDOWNbuttonuntilthedesktoplowersslightly,
then rises slightly and the display changes back to the numeric height setting.
*Note:“RST”willlooklike
“ASr”onthedisplay
®
Two-leg frame: 99.039.14.0050-V4
Three-leg frame: 99.046.14.0070
Four-leg frame: 99.052.09.0030
© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com R02

MINIMUM & MAXIMUM HEIGHT SETTINGS
The desk frame ships defaulted to its minimum and maximum height limits. These steps allow
the upper and lower limits to be adjusted to your preference.
Note: If memory settings were previously set outside of the new minimum and maximum height
settings, they will default to the new minimum and maximum settings. To set new minimum and
maximumheightsettingsoutsideofthecurrentsettings,youwillneedtorstremovethecurrent
minimum and maximum settings.
DISPLAY UNITS
Change the numeric display to show heights in either inches or centimeters.
 l. PresstheDOWNbuttonuntilthedeskreachesthelowestposition.Releasebutton.
 2. PresstheDOWNbuttonuntildisplayashes“RST”.
3. Press the “2” button until display shows “10.3” (centimeters) or “10.4” (inches) and goes
  backto“RST”.
Note:While“RST”isstillashing,youcanpressthe“2”buttonasmanytimesasyou’dlike
to toggle between the two settings.
4. Press the DOWN button until the desktop lowers slightly, then rises slightly and the display
changes back to the numeric height setting.
ANTI-COLLISION SENSITIVITY
ThedeskhasanAnti-CollisionSensitivitythatwillstopthedesk’smovementifithitssomethingontheway
downorup.YoucanchangethisSensitivitylevelbydoingthefollowing:
 l. PresstheDOWNbuttonuntilthedeskreachesthelowestposition.Releasebutton.
 2. PresstheDOWNbuttonuntildisplayashes“RST”.
 3. PresstheUPbuttonuntildisplayshows“10.5”,“10.6”,or“10.7”andgoesbackto“RST”.
“10.5” is code for the 10 kg (22 lbs) setting (most sensitive setting, false positives are
sometimes possible).
“10.6” is code for the 15 kg (33 lbs) setting
“10.7” is code for the 20 kg (44 lbs) setting (least sensitive setting).
Note:While“RST”isstillashing,youcanpresstheUPbuttonasmanytimesasyou’dlike
to toggle between the three settings.
4. Press the DOWN button until the desktop lowers slightly, then rises slightly and the display
changes back to the numeric height setting.
© UPLIFT Desk • 1-800-349-3839 • [email protected] • www.upliftdesk.com
To Set a new maximum desk height:
l. Press the UP or DOWN button to move the desk to the desired maximum height.
 2. Pressthe“M”buttononce,andthentheUPbuttononce.TheDisplaywillash“S-”
3. Press and hold the “M” button until the Display shows “999”,
and then changes to numeric value of new upper limit.
To Set a new minimum desk height:
l. Press the UP or DOWN button to move the desk to the desired minimum height.
 2. Pressthe“M”buttononce,andthentheDOWNbuttononce.TheDisplaywillash“S-”
3. Press and hold the “M” button until the Display shows “000”
and then changes to numeric value of new lower limit.
Removing adjusted maximum and minimum heights:
 l. Pressthe“M”button(thedisplaywillshow“S-”).
2. Press the “M” button again until the display shows “555”
and changes to the current numeric height setting.