URBAN OUTFITTERS GILLIAN User manual

GILLIAN CABINET
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 1 of 3
TOOLS REQUIRED BUT NOT INCLUDED:
Phillips head screwdriver, level, pencil
WARNINGS:
Do not throw away packing materials and carton until after
assembly. Assemble all parts on a clean smooth surface
CARE INSTRUCTIONS:
Avoid direct exposure to sunlight. Do not place overheat or air
conditioning vents. Adjust levelers so that the furniture sits flat on
uneven floors.
Blot spills do not rub, with a clean white cloth
Do not use harsh chemicals.
Before cleaning any part test a small spot in a hidden area.
You may need to re-tighten all bolts after initial use.
PARTS INCLUDED
(A) Top Panel (B) Side Panel (C) Side Panel (D) Bottom Panel
x1 x1 x1 x1
(E) Back Panel (F) Center Rail (G) Door (H) Door (I) Cleat
x1 x1 x1 x1 x1
HARDWARE LIST
(J) Hex key
x 1
(K) Bolt
[1/4” x 1”] x8
(L) Spring washer
[1/4”] x8
(M) Flat washer
[1/4”] x8
(N) Screw
[M4 x 30mm] x8
(O) Metal Anchor
[M15 x 28mm] x11
(P) Machine Screw
[M8 x 35mm] x11

GILLIAN CABINET
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 2 of 4
STEP 1
With help lay the Parts out onto a clean smooth surface such as carpet or cardboard. Align the Back Panel (E) with the Side
Panels (B&C) and press firmly into place as shown.
STEP 2
Align the Back Panels (E) and Side Panels (B&C) with the Bottom Panel (D) and press firmly into place. Insert Flat Washer (M),
Spring Washer (L) and Bolt (K) as shown. Tighten with supplied Hex Key (J). Do not over-tighten. Locate the holes in the Back
Panel (E), insert screws (N) and tighten with a Phillips head screwdriver (not provided).

GILLIAN CABINET
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 3 of 4
STEP 3
Align the Center Rail (F) to the Bottom Panel (D) and press firmly into place. Place the Top Panel (A) on top of the partially
assembled case as shown. Insert the Flat Washer (M), Spring Washer (L), and Bolt (K) through the side panels as shown.
Tighten with supplied Hex Key (J). Do not over-tighten. Roll the cabinet onto its back and insert the Screws (N) through the hole
in the Bottom Panel (D) and the hole in Center rail (F). Make sure they are in the center of each section and tighten with a Phillips
head screwdriver (not included).
STEP 4
Roll the case back onto its base. Align and insert the Doors (G) and (H) as shown below.

GILLIAN CABINET
Assembly Instructions
EXCLUSIVE AND CONFIDENTIAL PROPERTY OF URBAN OUTFITTERS, INC.
© 2017 UO, Inc. All rights reserved, including all applicable copyright, design and patent
rights. Any unauthorized reproduction, adaptation, distribution or other infringement will be
prosecuted.
Page 4 of 4
STEP 5
Place the cleat on the wall in its desired location. Ensure the cleat is level and mark the location of the screw holes. If attaching to
drywall, screw Metal anchors (O) into the wall at the marked hole locations, then screw Machine screws (P) through the cleat into
Metal anchors (O). If screwing into studs, no anchor is required.
STEP 6
With help hang, the Cabinet onto Wooden French Cleat (I) to complete assembly.