urmet domus 1083/12 Operating instructions

Programming guide
System Type C
1083/12 -1083/15 -1083/16

Contents
Introduction
Menu structure
Configuration procedure
Programming proximity access keys
Programming door open codes
Appendix
Contents
Introduction
Menu structure
Configuration procedure
Programming proximity access keys
Programming door open codes
Appendix
Contents
Introduction
Menu structure
Configuration procedure
Programming proximity access keys
Programming door open codes
Appendix
Configuration procedure
Programming proximity access keys
Programming door open codes
Configuration procedure
Programming proximity access keys
Programming door open codes
Programming proximity access keys
Page 1
Page
Page
Page 1
Page 1
Page 1
Page 1
Page
4
Page
5
Page 1
5
Page 1
6
Page 1
7

Introduction
System Type C -
One (or up to a maximum of four) ‘Main’ entry panels i.e. panels
which call all apartments in the system.
The apartment numbers are in any range.
This system type is used where;
1. There are more than 128 apartments in a single block
2. There are less than 128 apartments in a block but the
total amount of cable means that the system must be
separated into sections.
1083/50
1083/20
1083/20
1083/50
1083/75
1083/20
Page 1
This programming guide is intended specifically for a particular type of system –System Type C

4
4
Page 2
In
System Type
association between the real apartment
number (postal address) and the binary
address.
The binary address is made up from the
address of the 1083/50 Riser Interface and
the address set on the monitor, wall
bracket or handset
explanation.
Page 2
ADDRESS
System Type
association between the real apartment
number (postal address) and the binary
address.
The binary address is made up from the
address of the 1083/50 Riser Interface and
the address set on the monitor, wall
bracket or handset
explanation.
ADDRESS
System Type
C
it is
association between the real apartment
number (postal address) and the binary
The binary address is made up from the
address of the 1083/50 Riser Interface and
the address set on the monitor, wall
bracket or handset
explanation.
ADDRESS
3
it is
necessary to make an
association between the real apartment
number (postal address) and the binary
The binary address is made up from the
address of the 1083/50 Riser Interface and
the address set on the monitor, wall
bracket or handset
–
See Page
necessary to make an
association between the real apartment
number (postal address) and the binary
The binary address is made up from the
address of the 1083/50 Riser Interface and
the address set on the monitor, wall
See Page
3 for further
necessary to make an
association between the real apartment
number (postal address) and the binary
The binary address is made up from the
address of the 1083/50 Riser Interface and
the address set on the monitor, wall
3 for further
necessary to make an
association between the real apartment
number (postal address) and the binary
The binary address is made up from the
address of the 1083/50 Riser Interface and
3 for further

Page 3
7
4
3
1083/20
1
1083/75
ON
1083/20
34
2
5
1083/50
6
2
6
5
ON
1
8
Binary address 00
Binary address 003
Apartment number
(postal address) 4
4
The full binary address of apartment 4 is made up from th
e address of the
1083/50 Riser D
istributor (between
00 and 31) in this case 00, and the address of the monitor (between 000 and 127) –in this case 003
4
3
5
2
ON
1
67
2
8
5
4
6
1
ON
3
00 + 003 = 00 003
1083/50 DIP switch Monitor DIP switch
4
The full binary address
for
apartment 4 is 00 003

Menu Structure
LANGUAGE
CONFIGURATION
NAMES
DOOR OPENER
KEYS
RESET
SIMPLIFIED GUI
MODULE TYPE
MULTIRISE
ID PRIMARY MODULE
CODE TYPE
BUSY TIME
STOPABLE
DOOR LOCK 1 RELEASE TIME
DOOR LOCK 1
DOOR LOCK 2 RELEASE TIME
DOOR LOCK 2
PASSWORD
LCD BACKLIGHT
BUTTON SOUND
MULTITOUCH CALL
WELCOME MESSAGE
TIME ZONE
DATE AND TIME
DAY
POSTMAN
VOCAL SYNTHESIS
SWITCHBOARD
NEW
MODIFY
DELETE
DELETE ALL
NEW
MODIFY
DELETE
DELETE ALL
NEW
MODIFY
DELETE
Page 4

Configuration procedure
When the unit is first powered the screen is as follows –
On the entry panel keypad press 99999 and you will see this screen –
Enter 1000 (the default password) then press
Use the and buttons to select
LINGUA and press
Use the and buttons to select
ENGLISH UK and press
ENGLISH UK
Page 5

You see this screen –
Press the button to select CONFIGURATION then press
Use the or buttons to select NO and press
NO
YES
PRIMARY
SECONDARY
Use the or buttons to select PRIMARY and press
Use the or buttons to select NO and press
YES
NO
Page 6
LANGUAGE

CONFIGURATION

In a system with only one entry panel the ID is always 0. In this case just press .
In a system with two, three or four panels, each must have a different ID.
For example to change the panel ID to 1just press then press
Use the or buttons to select LOGICAL and press
It is suggested to keep the default setting by pressing
It is suggested to keep the default setting by pressing
Page 7
PHYSICAL
The ID of the panel is determined by where it is connected in the system.
You must refer to the connection diagram of your system for the ID of each panel.

DOOR LOCK 1 RELEASE TIME adjusts the voltage free relay (C NO NC) time
and also the solid state lock release output (SE+ SE-) time.
For example for a time of 10 seconds press 1 0
Choosing FREE means that the door can be opened by the monitor or handset at
any time without the monitor or handset being called.
Choosing SECRET means that the monitor or handset must be called before it can
open the door.
Use the or buttons to make a selection then press
DOOR LOCK 2 RELEASE TIME adjusts the voltage free relay (C NO) time.
For example for a time of 1 second press 1then press
Choosing FREE means that the gate can be opened by the monitor or handset at
any time without the monitor or handset being called.
Choosing SECRET means that the monitor or handset must be called before it can
open the gate.
Use the or buttons to make a selection then press
For an explanation of the three different lock outputs see the appendix
Page 1
4
Page 8