Vaporesso GEN FIT 40 User manual

USER
GUIDE
VAPORESSO GEN FIT 40

Thank you for choosing Vaporesso product. Please read
this instruction carefully before use to ensure a perfect
experience.
If there is any additional requirement about this product,
please consult the local agent or contact us through our
website: www.vaporesso.com
ENLARGED VIEW
SPECIFICATIONS
FIGURE
ENGLISH
GEN FIT 40 MOD
Dimensions 69.78 x 22.53 x 32.25mm
Resistance Range 0.3-1.2Ω
Output Power 5-40W
Output Voltage 0-4V
Charging Current DC 5V/2A, Type-C
Display 0.42" OLED Screen
Battery Capacity Built-in 2000mAh
Tank Connection 510 Thread
ITANK X
Dimensions Φ20 x 52.5 mm
Capacity 3.5ml / 2ml
Coils GTX 0.6Ω MESH Coil (12-26W)
GTX 1.2Ω Regular Coil (8-12W)
FIGURE 1

1. Install the Tank
Install the tank to the battery by screwing the 510 thread.
2. Replace the Coil (Refer to FIGURE 1)
- Unscrew the thread base from the tank;
- Pull out the used coil in the tank;
- Install a new coil to the tank;
- Reattach the thread base into place.
3. Fill the E-liquid (Refer to FIGURE 2)
- Push the top cap according to the arrow direction;
- Please wait5 minutes for the e-liquid to soak into the coil
completely.
on the bottom of the tank.
5. System Operating
(1) Power on/off: press the power
button 5 times in2s.
(2) Lock/unlock the Buttons:
press the power button 3 times
continuously to lock or unlock the “+”
button and “-” button.
(3) Start Vaping: press and hold the power button to start
vaping. For your safety, please do not vape for more than 10
seconds ata time.
SMART VW: select “SMART VW” and press the
power button to enter ON/OFF setting.
VW: select “VW” and press the power button to
enter VW mode.
VV: select “VV”and press the power button to
enter VV mode.
DEFAULT: select “DEFAULT”, “YES” and press
the power button to restore the factory setting.
(5) Flip the Screen:press the power button and “+” button
(6) System Setting: press the “+” button and “-” button
simultaneously to enter the system setting interface, which
includes VV, VW, SMART VW, and DEFAULT.
(4) Adjust the Power: press the “+” button or “-”
button to adjust the power.
USER INSTRUCATIONS
FIGURE 2

PROTECTIONS
(2) No-load Protection: when there is no tank
detected, the device will stop working and
“CHECK ATOMIZER” will show on the screen.
(3) Short-circuit Protection: when a short-
circuit is detected, the device will stop working
and “SHORT ATOMIZER” will show on the
screen.
(4) Low Voltage Protection: when the battery
voltage is too low to start vaping, the device can
not be operated and “LOW BATTERY” will show
on the screen.
(5) Over Discharge Protection: when the
battery voltage is extremely low during vaping,
the device will stop working.
(6) Over Charge Protection: the device will stop
charging when it is fully charged.
(7) USB Input Protection: when the USB
detects an input voltage exceeding the rated
voltage, the device will stop charging.
(1) Overtime Protection: the device will stop
working if you vape for more than 10 seconds
at a time, and “OVER TIME” will show on the
screen.
FRANÇAIS
CONSIGNES D’UTILISATION
1. Installation du réservoir
Installez le réservoir sur la batterie en les vissant ensemble
grâce au letage 510. Vériez qu’ils sont fermement
connectés.
2. Remplacer la Coil (voir la FIGURE)
- Dévissez la base letée du réservoir ;
- Retirez la coil usagée du réservoir ;
- Installez une nouvelle coil dans le réservoir ;
- Remettez la base letée en place.
3. Remplissez d'e-liquide [Voir la FIGURE]
- Dévissez le capuchon inférieur du réservoir.
- Remplissez de e-liquide par l'orice, puis verrouillez le
capuchon supérieur cela fait.
- Veuillez patienter 5 minutes, le temps que l’e-liquide imbibe
complètement la coil.
4. Ajuster le Débit d'air
Tournez l’anneau d’entrée d’air installé au bas du réservoir
pour ajuster le débit de l’air.
5. Fonctionnement du système
(1) Marche/Arrêt : appuyez sur le
bouton d'alimentation à 5 reprises
en 2 secondes.
(2) Verrouillage/déverrouillage
des boutons : appuyez sur le
bouton d'alimentation à 3 reprises
successives pour verrouiller ou
déverrouiller le bouton « + » et le
bouton « - ».