Vertiv NetSure 2100 Series User manual

NetSure™ 2100 Series
-48 VDC Power System
Installation Manual (IM582138000), Revision C
Specification Number: 582138000
Model Number: 2100

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
2
The information contained in this document is subject to change without
notice and may not be suitable for all applications. While every precaution
has been taken to ensure accuracy and completeness herein, Vertiv Group
Corp. assumes no responsibility, and disclaims all liability, for damages
resulting from use of this information or for any errors or omissions. Refer
to other local practices or building codes as applicable for the correct
methods, tools, and materials to be used in performing procedures not
specifically described in this document.
This document may contain confidential and/or proprietary information of
Vertiv Group Corp., and its receipt or possession does not convey any right
to reproduce, disclose its contents, or to manufacture or sell anything that
it may describe. Reproduction, disclosure, or use without specific
authorization from Vertiv Group Corp. is strictly prohibited.
Vertiv and the Vertiv logo are trademarks or registered trademarks of
Vertiv Group Corp. All other names and logos referred to are trade names,
trademarks or registered trademarks of their respective owners.
© 2019 Vertiv Group Corp. All rights reserved.

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
3
TABLE OF CONTENTS
Admonishments Used in this Document............................................................6
Important Safety Instructions ..............................................................................7
Safety Admonishments Definitions......................................................................................................7
General Safety ...........................................................................................................................................................7
Voltages...........................................................................................................................................................................7
AC Input Voltages........................................................................................................................................................ 7
DC Output and Battery Voltages .................................................................................................................. 7
Battery .............................................................................................................................................................................. 8
Personal Protective Equipment (PPE)............................................................................................. 9
Hazardous Voltage..............................................................................................................................................9
Handling Equipment Containing Static Sensitive Components............................. 9
Maintenance and Replacement Procedures..............................................................................9
Static Warning.........................................................................................................10
Customer Documentation Package....................................................................11
Installation Acceptance Checklist......................................................................11
Installing the System............................................................................................. 13
General Requirements....................................................................................................................................13
Securing the Relay Rack to the Floor (if furnished) .........................................................14
Securing the System to a Relay Rack or a Cabinet Equipment Rack
(if required)................................................................................................................................................................18
Securing the System to a Wall with Wall Bracket Kit P/N 541285 (if
furnished) ....................................................................................................................................................................19
Installing a List 93, 94 Battery Tray and Optional Battery Tray Circuit
Breaker.......................................................................................................................................................................... 22
Battery Tray Installation...................................................................................................................................... 22
Optional Battery Disconnect Circuit Breaker Installation.................................................. 30
Installing Circuit Breakers and Fuses ..............................................................................................31
Installing GMT Load Distribution Fuses (List AA, BA, BB, CA) ......................................31
Installing Bullet Nose Type Load Distribution Circuit Breakers (List CA).........33
Installing Bullet Nose Type Battery Disconnect Circuit Breaker (List
BB)........................................................................................................................................................................................... 34
Installing Compact Type Load Distribution Circuit Breakers (List BA,
BB)............................................................................................................................................................................................35
Installing an Optional Battery Cabinet............................................................................................37
Installing an Optional External IB4 Kit P/N 559239..........................................................38
Attaching Supplied USB Drive Storage Pouch Near Power System...............39
Making Electrical Connections..........................................................................40
Important Safety Instructions ............................................................................................................... 40
Wiring Considerations................................................................................................................................... 40
Relay Rack / Cabinet Frame Grounding Connection..................................................... 40
System Shelf Frame Grounding Connection............................................................................41
Relay or Cabinet Rack........................................................................................................................................... 41

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
4
Wall Mounting............................................................................................................................................................... 41
Central Office Ground Connection ....................................................................................................41
Rectifier Nominal 120 VAC / 208 VAC / 240 VAC Input and AC Input
Equipment Grounding Connections................................................................................................42
General.................................................................................................................................................................................42
AC Input Connections to Rear AC Input IEC Receptacles, if furnished................42
AC Input Connections When System is Pre-Wired in a Vertiv OSP
Cabinet.................................................................................................................................................................................42
AC Input Connections when Single AC Input Line Cord or AC Input
Cable Assembly is Factory Installed........................................................................................................42
External Alarm, Reference, Monitoring, and Control Connections ...................45
Connection Point Locations........................................................................................................................... 45
RS-485 Connector J5............................................................................................................................................47
Mini Control Unit CAN Port Connector J4 (RJ-45).................................................................47
Temperature Probe Port Connectors J8 and J9....................................................................... 48
Optional External IB4 Connector J11 ..................................................................................................... 48
Digital Inputs and Relay Outputs Connector J3......................................................................... 48
Circuit Breaker Alarm Connections to Battery Disconnect Circuit
Breakers on Battery Trays.................................................................................................................................51
Circuit Breaker Alarm Connections to Battery Disconnect Circuit
Breakers on Battery Cabinets....................................................................................................................... 54
Mini Control Unit Ethernet Connection (if required)...................................................... 57
Mini Control Unit Second Ethernet Port Connection (if Optional
External IB4 Kit P/N 559239 Furnished).....................................................................................58
General.................................................................................................................................................................................58
Default IB4 Ethernet Port Parameters ..................................................................................................58
Load Distribution Wiring, Input Battery Wiring, and CO Ground
Wiring............................................................................................................................................................................. 60
Load Distribution Wiring, Input Battery Wiring, and CO Ground Wiring
To List AA........................................................................................................................................................................ 60
Load Distribution Wiring, Input Battery Wiring, and CO Ground Wiring
to List CA...........................................................................................................................................................................62
Load Distribution Wiring, Input Battery Wiring, and CO Ground Wiring
to List BA .......................................................................................................................................................................... 64
Load Distribution Wiring, Input Battery Wiring, and CO Ground Wiring
to List BB............................................................................................................................................................................67
Connecting to an Optional Battery Cabinet ............................................................................70
Installing and Connecting Batteries in an Optional List 93 or 94
Battery Tray (if furnished).........................................................................................................................70
Important Safety Instructions....................................................................................................................... 70
Installing and Connecting Batteries........................................................................................................ 70
Installing Rectifier Modules.................................................................................73
Initially Starting, Configuring, and Checking System Operation..............73
Important Safety Instructions .................................................................................................................73
Initial Startup Preparation...........................................................................................................................73
Initially Starting the System......................................................................................................................73

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
5
Configuring the System ...............................................................................................................................74
Mini Control Unit........................................................................................................................................................74
Mini Control Unit (Controller) Initialization.......................................................................................74
Setting the Mini Control Unit as Required for Your Application..................................76
Checking System Operation.................................................................................................................... 79
Checking System Status.............................................................................................................................85
Final Steps .................................................................................................................................................................85

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
6
ADMONISHMENTS USED IN THIS DOCUMENT
DANGER
! Warns of a hazard the reader will be exposed to that will likely result
in death or serious injury if not avoided. (ANSI, OSHA)
WARNING
! Warns of a potential hazard the reader may be exposed to that could
result in
death or serious injury if not avoided. This admonition is not used for situations that pose a
risk only to equipment, software, data, or service. (ANSI)
CAUTION
! Warns of a potential hazard the reader may be exposed to that could
result in minor or moderate injury if not avoided. (ANSI, OSHA) This admonition is not
used for situations that pose a risk only to equipment, data, or service, even if such use
appears to be permitted in some of the applicable standards. (OSHA)
ALERT
!Alerts the reader to an action that must be avoided in order to protect
equipment, software, data, or service. (ISO)
ALERT
! Alerts the reader to an action that must be performed in order to prevent
equipment damage, software corruption, data loss, or service interruption. (ISO)
FIRE SAFETY
! Informs the reader of fire safety information, reminders, precautions,
or policies, or of the locations of fire
-fighting and fire-safety equipment. (ISO)
SAFETY
! Informs the reader of general safety information, reminders, precautions, or
policies not related to a particular source of hazard or to fire safety. (ISO, ANSI, OSHA)

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
7
IMPORTANT SAFETY INSTRUCTIONS
Safety Admonishments Definitions
Definitions of the safety admonishments used in this document are listed under “Admonishments Used in this
Document” on page 6.
General Safety
DANGER! YOU MUST FOLLOW APPROVED SAFETY PROCEDURES.
Performing the following procedures may expose you to hazards. These procedures should be
performed by qualified technicians familiar with the hazards associated with this type of equipment.
These hazards may include shock, energy, and/or burns. To avoid these hazards:
a) The tasks should be performed in the order indicated.
b) Remove watches, rings, and other metal objects.
c) Prior to contacting any uninsulated surface or termination, use a voltmeter to verify that no voltage
or the expected voltage is present. Check for voltage with both AC and DC voltmeters prior to
making contact.
d) Wear eye protection.
e) Use certified and well maintained insulated tools. Use double insulated tools appropriately rated for
the work to be performed.
Voltages
AC Input Voltages
DANGER! This system operates from AC input voltage capable of producing fatal electrical shock. AC
input power must be completely disconnected from the branch circuits wiring used to provide power to
the system before any AC electrical connections are made. Follow local lockout/tagout procedures to
ensure upstream branch circuit breakers remain de-energized during installation. DO NOT apply AC
input power to the system until all electrical connections have been completed and checked.
DC Output and Battery Voltages
DANGER! This system produces DC power and may have a battery source connected to it. Although
the DC voltage is not hazardously high, the rectifiers and/or battery can deliver large amounts of current.
Exercise extreme caution not to inadvertently contact or have any tool inadvertently contact an output
terminal or battery terminal or exposed wire connected to an output terminal or battery terminal.
NEVER allow a metal object, such as a tool, to contact more than one termination or battery terminal at a
time, or to simultaneously contact a termination or battery terminal and a grounded object. Even a
momentary short circuit can cause sparking, explosion, and injury.
DANGER! Follow local lockout/tagout procedures to ensure DC branch circuit protection devices
remain de-energized during installation at loads, as required.

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
8
Battery
Refer to the battery manufacturer documentation for specific battery safety instructions. The following are
general guidelines.
WARNING! Correct polarity must be observed when connecting battery leads.
WARNING! Special safety precautions are required for procedures involving handling, installing, and
servicing batteries. Observe all battery safety precautions in this manual and in the battery instruction
manual. These precautions should be followed implicitly at all times.
WARNING! A battery can present a risk of electrical shock and high short circuit current. Servicing of
batteries should be performed or supervised only by properly trained and qualified personnel
knowledgeable about batteries and the required precautions.
The following precautions should be observed when working on batteries:
•Follow the recommended PPE requirements per the SDS for the battery to be used.
•Batteries are an energy source that can produce high amounts of electrical current.
•Remove watches, rings, and other metal objects.
•Eye protection should be worn to prevent injury from accidental electrical arcs.
•Use certified and well maintained insulated tools. Use double insulated tools appropriately rated for
the work to be performed. Ensure that wrenches with more than one working end have only one
end exposed.
•Do not lay tools or metal parts on top of batteries.
•Verify that no current will flow when the battery is connected or disconnected by opening battery
disconnects (if available) or adjusting the system to match battery voltage.
•Risk of explosion if battery is replaced with an incorrect type or if polarity is reversed.
Recommended to replace batteries with the same manufacturer and type, or equivalent.
•Dispose of used batteries according to the instructions provided with the batteries. Do not dispose
of batteries in a fire. They may explode.
•Batteries may generate explosive gases during normal operation. Systems containing batteries
should never be installed in an airtight room or space. Only install in a ventilated environment.
•Batteries may contain sulfuric acid. If battery acid enters your eye, immediately flush your eye with
running cold water for at least 15 minutes. Get medical attention immediately. If battery acid
contacts skin or clothing, wash immediately with soap and water.
•Do not open or mutilate batteries.
•ALWAYS FOLLOW THE BATTERY MANUFACTURER’S RECOMMENDATIONS AND SAFETY
INSTRUCTIONS.

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
9
ALERT! Performing maintenance and/or troubleshooting procedures may interrupt power to the loads,
if battery reserve is not sufficient.
Personal Protective Equipment (PPE)
DANGER! ARC FLASH AND SHOCK HAZARD.
Appropriate PPE and tools required when working on this equipment. An appropriate flash protection
boundary analysis should be done determine the “hazard/risk” category, and to select proper PPE.
This product is intended only for installation in a Restricted Access Location.
Only authorized and properly trained personnel should be allowed to install, inspect, operate, or maintain
the equipment.
Do not work on LIVE parts. If required to work or operate live parts, obtain appropriate Energized Work
Permits as required by the local authority, per NFPA 70E “Standard for Electrical Safety in the
Workplace”.
Hazardous Voltage
DANGER! HAZARD OF ELECTRICAL SHOCK.
More than one disconnect may be required to de-energize the system before servicing.
Handling Equipment Containing Static Sensitive Components
ALERT! Installation or removal of equipment containing static sensitive components requires careful
handling. Before handling any equipment containing static sensitive components, read and follow the
instructions contained on the Static Warning Page.
Maintenance and Replacement Procedures
CAUTION! When performing any step in procedures that requires removal or installation of hardware,
use caution to ensure no hardware is dropped and left inside the unit; otherwise service interruption or
equipment damage may occur.
NOTE! When performing any step in procedures that requires removal of existing hardware, retain all
hardware for use in subsequent steps, unless otherwise directed.

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
10
STATIC WARNING
This equipment contains static sensitive components. The warnings listed below must be observed to
prevent damage to these components. Disregarding any of these warnings may result in personal injury
or damage to the equipment.
1. Strictly adhere to the procedures provided in this document.
2. Before touching any equipment containing static sensitive components, discharge all static
electricity from yourself by wearing a wrist strap grounded through a one megohm resistor. Some
wrist straps have a built-in one megohm resistor; no external resistor is necessary. Read and follow
wrist strap manufacturer’s instructions outlining use of a specific wrist strap.
3. Do not touch traces or components on equipment containing static sensitive components. Handle
equipment containing static sensitive components only by the edges that do not have connector
pads.
4. After removing equipment containing static sensitive components, place the equipment only on
static dissipative surfaces such as conductive foam or ESD bag. Do not use ordinary Styrofoam™or
ordinary plastic.
5. Store and ship equipment containing static sensitive components only in static shielding containers.
6. If necessary to repair equipment containing static sensitive components, wear an appropriately
grounded wrist strap, work on a conductive surface, use a grounded soldering iron, and use
grounded test equipment.

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
11
CUSTOMER DOCUMENTATION PACKAGE
This document (IM582138000) provides Installation Instructions for the NetSure™ 2100 SERIES -48 VDC Power
System: Model 2100, Spec. No. 582138000.
The complete Customer Documentation Package consists of…
Document Number Document Description How Provided
IM582138000
Power System Installation
Instructions Printed Manual and PDF File
UM1M831ANA
Mini Control Unit User
Instructions Printed Manual and PDF File
(per configuration file loaded into
controller)
Mini Control Unit Configuration
Drawing (C-drawing) Printed Document and PDF File
UM582138000
Power System User Instructions
PDF files are provided on a
supplied USB drive.
See also Note 1.
SAG582138000
Power System “System
Application Guide”
UM1R481000e3 Rectifier Instructions
Section 4154
Contact Information Page
SD582138000
Power System Schematic
Diagram
T582138000 Power System Wiring Diagram
Note 1: Also provided on the USB drive is a controller configuration drawing and the controller configuration
files loaded into the controller as shipped.
For factory settings of all configurable controller parameters, refer to the controller configuration drawing
(C-drawing) supplied with your power system.
INSTALLATION ACCEPTANCE CHECKLIST
Provided in this section is an Installation Acceptance Checklist. This checklist helps ensure proper installation
and initial operation of the system. As the procedures presented in this document are completed, check the
appropriate box on this list. If the procedure is not required to be performed for your installation site, also
check the box in this list to indicate that the procedure was read. When installation is done, ensure that each
block in this list has been checked. Some of these procedures may have been factory performed for you.
NOTE! The system is not powered up until the end of this checklist.
NOTE! Some of these procedures may have been performed at the factory for you.

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
12
Installing the System
Relay Rack Secured to Floor (if furnished)
System Secured to Relay Rack or Cabinet Equipment Rack (if required)
System Secured to Suitable Wall (if required)
Optional Battery Tray Installed
Optional Battery Tray Battery Disconnect Circuit Breaker Installed
Circuit Breakers and/or Fuses Installed
Optional Battery Cabinet Installed
Optional External IB4 Kit Installed
Supplied USB Drive Storage Pouch Attached Near Power System
Making Electrical Connections
Relay Rack / Cabinet Frame Grounding Connection Made
System Shelf Frame Grounding Connection Made
Central Office Ground Connection Made
Rectifier AC Input and AC Input Equipment Grounding Connections Made
External Alarm, Reference, Monitoring, and Control Connections Made
Mini Control Unit Ethernet Port Connection Made
Mini Control Unit Second Ethernet Port Connection Made (if required)
Load Connections Made
Battery Connections Made
-Batteries Installed and Connected in an Optional Battery Tray
-Batteries Installed and Connected in an Optional Battery Cabinet
-External Batteries Connected
Installing the Modules
Rectifier Modules Installed
Initially Starting the System
System Started, Configured, and Checked

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
13
INSTALLING THE SYSTEM
General Requirements
NOTE! The system is furnished for 19” mounting as standard. For 23” mounting, replace the 19”
mounting brackets on the shelf with the 23” mounting brackets (supplied with the system). A wall
mounting option is also available. See SAG582138000 for ordering information.
•The installer should be familiar with the installation requirements and techniques to be used in securing
the relay rack (if furnished) to the floor.
•The installer should be familiar with the installation requirements and techniques to be used in securing
the system to a relay rack or equipment rack.
-The top rear cover needs to be removed to access the battery and/or CO ground connection points.
If other equipment is mounted above the shelf, leave enough clearance to access the screws
securing the cover.
•The installer should be familiar with the installation requirements and techniques to be used in securing
the system to a suitable wall (if required).
•This product is intended only for installation in a restricted access location on or above a non-
combustible surface.
•This product must be located in a controlled environment with access to crafts persons only.
•This product is intended for installation in network telecommunication facilities (CO, vault, hut, or other
environmentally controlled electronic equipment enclosure).
•This product is intended for connection to the common bonding network in a network
telecommunication facility (CO, vault, hut, or other environmentally controlled electronic equipment
enclosure).
•The DC return connection to this system can remain isolated from system frame and chassis (DC-I).
•This system is suitable for installation as part of the Common Bonding Network (CBN).
•The system must be mounted in an environment that does not exceed the rated operating ambient
temperature range found in SAG582138000.
•Clearance requirements are (relay rack or equipment rack):
-Minimum clearance is one inch from the face of the rectifier modules and one inch from the surface
of the rear sheet metal (for ventilation only; operation, installation and maintenance require more
clearance).
-Recommended minimum aisle space clearance for the front of each bay is 2' 6"
(for operation and maintenance).
-Recommended minimum aisle space clearance for the rear of each bay is 2’ 0”
(for installation and maintenance).
-List AA and CA: No space required above or below the unit (for ventilation only, installation and
maintenance may require more clearance).
-List BA and BB: Space is required above or below the unit (for ventilation only, installation and
maintenance may require more clearance).

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
14
•Clearance requirements are (cabinet or wall mounting):
-Minimum clearance is one inch from the face of the rectifier modules and one inch from the surface
of the rear sheet metal (for ventilation only; operation, installation and maintenance require more
clearance).
-The system may also be mounted horizontally or vertically. Vertical mounting can be with the
distribution located at the top of the unit orientation or at the bottom of the unit orientation.
Securing the Relay Rack to the Floor (if furnished)
Secure the relay rack to the floor per site requirements. Refer to “General Requirements” on page 13.
Ventilation Requirements
Refer to “General Requirements” on page 13.
Relay Rack Floor Mounting Dimensions
Refer to Figure 1and Figure 2for relay rack floor mounting dimensions.

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
15
Figure 1: Relay Rack Floor Mounting Dimensions - 23” (cont’d on next page)
Part No. 559817
Part No. 559819
Part No. 559818, 559820,
559821, 559822
17.50
20.13
24.38
2.13
3.44
9.88
12.53
15.00
1.24
2.56
0.875 Dia.
(8 Places)
Masked for Frame Ground Lug
0.281 Dia. Holes on 0.625 Centers
(Top of Rack, 2 Places)
22.500
24.750
1.125
15.000
17.500
20.125
25.000
2.437
3.750
9.871
12.531
15.031
1.250
2.580
2.00
1.00
1.00
2.00
2.00
2.00
5.00
0.437 Dia.
(12 Places)
Masked for Frame Ground Lug
0.281 Dia. Holes on 0.625 Centers
(Top of Rack, 2 Places)
0.875 Dia.
(8 Places)
Masked for Frame Ground Lug
0.281 Dia. Holes on 0.625 Centers
(Top of Rack, 1 Place)
Notes:
1. All dimensions are in inches.

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
16
Figure 1: Relay Rack Floor Mounting Dimensions - 23” (cont’d from previous page)
19.685
25.80
15.000
1.502.83
18.00
0.875
8 Places
Part No.
562353 12.340
22.310
3.06
1.74
Notes:
1. All dimensions are in inches.

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
17
Figure 2: Relay Rack Floor Mounting Dimensions - 19”
Part No. 559823
Part No. 559824
13.50
16.13
20.38
2.13
3.44
9.88
12.53
15.00
1.24
2.56
0.875 Dia.
(8 Places)
Masked for Frame Ground Lug
0.281 Dia. Holes on 0.625 Centers
(Top of Rack, 2 Places)
Masked for Frame Ground Lug
0.281 Dia. Holes on 0.625 Centers
(Top of Rack, 2 Places)
14.13
16.75
21.00
2.13
3.44
9.38
12.03
15.00
1.49
2.81
0.875 Dia.
(8 Places)
Notes:
1. All dimensions are in inches.
Masked for Frame Ground Lug
0.334 Dia. Holes on 0.625 Centers
(Top of Rack, 2 Places)
Part No. 563922
15.69
18.31
21.80
1.76
3.07
12.34
15.00
18.00
1.50
2.83
0.812 Dia.
(8 Places)

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
18
Securing the System to a Relay Rack or a Cabinet Equipment Rack (if required)
DANGER! If the system is mounted in a relay rack, the relay rack must be securely anchored to the floor
before the system is installed.
NOTE! Refer to “General Requirements” on page 13 for mounting restrictions and ventilation
requirements.
This power system is designed to mount in a standard 19” or 23” relay rack or equipment rack having 1” or 1 3/4”
multiple drillings. Refer to System Application Guide SAG582138000 for overall dimensions and a list of
available relay racks.
Procedure
1. The system is furnished for 19” mounting as standard. For 23” mounting, replace the 19” mounting
brackets on the shelf with the 23” mounting brackets (supplied with the system).
2. Position the system in the relay rack or cabinet equipment rack.
3. Secure the system to the relay rack or cabinet equipment rack using hardware as shown in Figure 3
(see Figure 3for recommended torque). Use grounding washers as indicated in Figure 3.
NOTE! Install (orient) the ground washers so the teeth dig into the mounting angles for a secure
ground connection.
NOTE! Compliance with Telcordia GR-1089-CORE requires that prior to mounting the system to the
equipment rack:
oAll paint must be removed from the front surface of each equipment rack rail where it mates with a
shelf-mounting bracket, so that good metal-to-metal contact can be established between the shelf
and rack.
oThe shelf-to-rack mating surfaces must be cleaned.
oElectrical anti-oxidizing compound must be applied to the shelf-to-rack mating surfaces.
Figure 3: Mounting the System in a Relay Rack or a Cabinet Equipment Rack
Front
Mounting Hardware
12-24 x 3/4" Thread Forming
Hex Head Screw
No. 10/12 Ground Washer
Torque: 65 in-lbs.

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
19
Securing the System to a Wall with Wall Bracket Kit P/N 541285 (if furnished)
An optional wall mount bracket kit (P/N 541285) is available for horizontal or vertical wall mounting of the
system.
NOTE! Refer to “General Requirements” on page 13 for mounting restrictions and ventilation
requirements.
Procedure
1. The installer must provide fasteners for securing the system to a wall or other vertical surface. Ensure
that the wall and fastening technique are suitable for supporting the weight of the system. Refer to
System Application Guide SAG582138000 for system weight and additional dimensions.
2. Select either the vertical-mount or horizontal-mount brackets as required for your application. Attach
the brackets to the system mounting angles using kit-furnished screws. Torque to 60 in-lbs. Refer to
Figure 4or Figure 5.
3. Using the drill guide dimensions in Figure 4or Figure 5, prepare the wall for customer-furnished
fasteners. Secure the system to the wall.

Vertiv |NetSure™ 2100 Series -48 VDC Power System Installation Manual (IM582138000)|Rev. C
20
Figure 4: Horizontal Wall Mounting with P/N 541285
0.90
18.80
Wall Mount Drill Guide (Not to scale)
0.277 Dia. Clearance
Hole in Bracket
for Wall Fastener
.90
18.80
13.19
19.53
Notes:
1. All dimensions are in inches, unless otherwise specified.
2. Installer to furnish hardware for fastening brackets to wall.
Front
Horizontal
Wall Mounting
Bracket (2)
Installer to furnish hardware
for fastening brackets to wall.
Fasten kit brackets
to shelf angles with
kit-furnished fasteners.
Fasten kit brackets
to shelf angles with
kit-furnished fasteners.
Installer to furnish hardware
for fastening brackets to wall.