VEVOR LCWB90 User manual

LCWB90
USER MANUAL
Poable Workbench

Have product questions? Need technical suppo? Please feel free to contact us:
CustomerSe[email protected]
NEED HELP? CONTACTUS!
This is the original instruction, please read all manual instructions carefully before
operating. VEVOR resees clear interpretation of our user manual. The appear-
ance of the product shall be subject to the product you received. Please forgive us
that we won't inform you again if there is any technology or software updates on
our product.
Poable Workbench
01

02
GENERAL SAFETY RULES
WORKPLACE
PORTABLE WORKBENCH USE AND PRECAUTIONS.
IMPORTANT: carefully read the instructions in this manual as well as the general
safety instructions before using this tool.
WARNING ! Read the instructions and use or operate without following the instruc-
tions listed below will result in deformation, inexible movement, loss of bearing
weight or serious inju.
Before using the tool, read the instruction book carefully.
1) Keep the workplace clean and bright. A messy and dark place can cause
accidents.
2) Do not expose the workbench to rain or wet environment.
3) Pay attention to whether the ground is smooth when working outdoors to prevent
tilt and collapse.
1) Check whether the screws and nuts are tightened to prevent collapse during use.
2) When preparing for work, check whether the universal wheel is locked to prevent
sliding during use.
3) Use safety devices. Always wear gloves.
4) Maintain the poable workbench, check the installation deviation of the moving
pas, whether it is stuck, screw damage and other conditions aecting the opera-
tion of the poable workbench, such as damage, poable workbench must be
repaired before use, many accidents caused by poor maintenance.

03
MAINTENANCE
PRODUCT PARAMETER
1) Send your poable workbench to professional maintenance personnel, must use
the same spare pas for replacement, this will ensure the safety of use after mainte-
nance.
Model
Length
Width
Maximum Adjustable Height
Medium Adjustable Height
Minimum Adjustable Height
Load Limit
G.W
N.W
LCWB90
700 mm
600 mm
900 mm
850 mm
800 mm
100 lbs
25.4 kg
21.9 kg

04
STRUCTURE AND PART NAME

05
Name of Pas:
1: Platform
2: Panel
3: WB90 Column
4: WB90 Column
5: Bulkhead
6: Bower Bulkhead
7: Universal Wheel
8: Directional Wheel
9: M6 Flange Nut
10: M6 Carriage Screws
11: M8 Hex Socket Screws
12: M8 Flange Nuts
13: M8 Hexagon Socket
Countersunk Head Screws

06
ASSEMBLE STEPS
STEP. 1
Fix 7 (universal wheel) and 8 (universal wheel) to 6 (lower divider) with 11 (M8 hex
socket screws) and 12 (M8 ange nut).2. The tool is intended for household and
professional use .
STEP. 2
Use 10 (M6 carriage screws) and 9 (M6 ange nuts) to make 4 (WB90 column 2)
xed in 6 (lower paition) around.
STEP. 3
Fix 5 (paition) into 4 (WB90 column 2) with 10 (M6 carriage screws) and 9 (M6
ange nuts) .
STEP. 4
Fix 3 (WB90 Post 1) on the remaining two holes of 4 (WB90 post 2) with 10 (M6
carriage screws) and 9 (M6 ange nuts).
STEP. 5
Fix 2 (panel) into 3 (WB90 column 1). Put 10 (M6 carriage screw) and 9 (M6 ange
nut) into the top two holes of 3 (WB90 column 1) and tighten.
STEP. 6
Put 1 (bench) on 2 (panel), put 13 (M8 hexagonal countersunk head screw) into 1
(bench) four holes to tighten, make it xed.

07
ADJUST THE HEIGHT
1) The maximum height is 900mm. As shown in the gure: First, align the hole
positions in 1.2.3 of Figure 3 (WB90 column 1) and 4 (WB90 column 2), then inse
10 (M6 carriage screws) and 9 (M6 ange nuts) into the hole 1.2.3 and tighten them.
2) Medium height 850mm as shown in Figure 1: First align hole 3 (WB90 column 1)
and hole 4 (WB90 column 2) 2.3.4 one by one, then inse 10 (M6 carriage screws)
and 9 (M6 ange nuts) into hole 2.3.4 and tighten it.

08
3) Minimum height of 800 as shown in Figure3 . First, align holes 3 (WB90 column 1)
and 4 (WB90 column 2) 3.4.5 one by one, then inse 10 (M6 carriage screws) and 9
(M6 ange nuts) into hole 3.4.5 and tighten them

09
Impoer: WAITCHX
Address: 250 bis boulevard Saint-Germain 75007 Paris
Impoer: FREE MOOD LTD
Address: 2 Holywell Lane, London, England, EC2A 3ET
MADE IN CHINA
Manufacturer：ZHEJIANG LANGCHENG INDUSTRY&TRADE CO., LTD
Address：No.18 Weisan East Road, Hardware Machine Industrial Zone,
Tongqin Town,Wuyi County, Jinhua City 321201 Zhejiang, P.R.China

E-mail: CustomerSe[e-mail]