Viavi OneAdvisor 1000 User manual

VIAVI//Public
OneAdvisor 1000 High-Speed Network Testing Platform
OneAdvisor 1000 High-Speed Network Testing Platform
QUICK CARD
DS3 Bit Error Rate Testing (BERT)
This quick card describes how to configure and run a DS3 Bit Error Rate Test to a hard
loop, or another similarly configured VIAVI Test Instrument.
•OneAdvisor 1000 equipped with the following:
o100G Transport Module
oBERT software release V30.1.0 or greater
oC5DS3STS1 test option: DS3/STS-1 Electrical
oC5DUALPORT test option
•Two (2) mini-BNC to BNC adapters (CB-MINITOBNCQTY1)
•One of the following DS3 cable sets to connect the
T-BERD 5800 DS3 Port(s) to the line under test:
oTwo (2) BNC to BNC cables (CB-30662)
oTwo (2) BNC to WECO 440Acables (CB-015837) Figure 1: Equipment Requirements
LAUNCH TEST
1. Press the Power button to turn on the
OneAdvisor.
2. Press the 100G Module Test icon
at the top of the screen.
3. Tap the Power button and click
to launch the 100G Module.
4. Using the Select Test menu, Quick Launch
menu, or Job Manager, launch the
DS1/DS3►DS3►DS3 BERT►Terminate
test.
Figure 2: Launch 100G Module
Figure 3: Launch Test

VIAVI//Public
OneAdvisor 1000 High-Speed Network Testing Platform
OneAdvisor 1000 High-Speed Network Testing Platform
QUICK CARD
2
•The following Information is needed to
configure the test:
•DS3 Framing (C-BIT or M13)
•Clock Source (Internal or Recovered)
•Test Patterns(s)
•BER Pass/Fail Threshold
1. Tap to open the Tools Panel and
select .
2. Press to continue.
3. Press the Setup soft key on the top right
side of the screen.
4. Select the indicated folders and configure
your test as follows. Leave all other values at
default, unless specified in the work order.
5. Press the Results soft key to view the
Test Results screen.
Figure 4: Work Order
CONFIGURE TEST
Folder
Option
Value(s)
Interface
Rx Input
Term
Clock Source
If unknown,
select “Internal”
Clock Offset
0 ppm
LBO
0 dB
Framing
Framing
If unknown,
select “C
-BIT”
Pattern
Pattern Mode
ANSI
Pattern
2^23
-1 ANSI
Figure 5: Reset Test to Defaults
Figure 8: Setup, Pattern
Figure 7: Setup, Framing
Figure 6: Setup, Interface

VIAVI//Public
OneAdvisor 1000 High-Speed Network Testing Platform
OneAdvisor 1000 High-Speed Network Testing Platform
QUICK CARD
3
RUN TEST
1. Using drop-down menus , select
“Interface/Signal” for the right results display.
2. Press the Restart soft key .
3. Verify the following:
►Summary LED is green.
►Signal Present LED is green.
If the LED is red, check your cables.
Tx and Rx may be reversed.
►Frame Sync LED is green.
►RX Frequency (Hz)
= 44736000 +/- 895 Hz.
4. Using drop-down menus , select
“Payload/BERT” for the right results display.
5. Allow the test to run for desired duration and
verify the following:
►Pattern Sync LED is green.
►Bit/TSE Error Rate result does not
exceed your required threshold.
(0.00E+00 if pass/fail threshold unknown)
Figure 10: Results, Interface/Signal
Figure 9: Mini-BNC Connectors
CONNECT TO LINE UNDER TEST
•The OneAdvisor 100G Transport
Module has mini-BNC ports for
DS3 testing.
•CB-MINITOBNCQTY1 adapters
are required to adapt to a
standard BNC connector.
•You may use BNC to BNC or
BNC to WECO cables to connect
the adapter to the line under test.
Figure 11: Results, Payload BERT

VIAVI//Public
OneAdvisor 1000 High-Speed Network Testing Platform
OneAdvisor 1000 High-Speed Network Testing Platform
QUICK CARD
© 2022 VIAVI Solutions, Inc,
Product specifications and descriptions in this
document are subject to change without notice.
Patented as described at viavisolutions.com/patents
Contact Us
To reach the VIAVI office nearest you,
visit viavisolutions.com/contact
+1 844 GO VIAVI
([phone])
CREATE REPORT
6. In the OneAdvisor’s Quick Config menu,
change “Pattern” to the next value in the test
plan.
7. Press the Restart soft key to reset results.
8. Allow test to run for desired duration and verify
the following:
►Pattern Sync LED is green.
►Bit/TSE Error Rate does not exceed
your required threshold.
(0.00E+00 if pass/fail threshold unknown)
9. Repeat steps 6 through 8 for all Patterns in the
test plan. Patterns may include:
►Delay: Measures Round Trip Delay (RTD)
instead of Bit Errors (RTD values are shown
instead of BER in the “Payload/BERT”
results display)
►Others
Figure 12: Results, Quick Config
Figure 13: Results, Delay
1. Tap to open the Reports Panel and
select . .
2. Tap .
3. A report will be saved to the OneAdvisor 1000
100G Module’s /bert/reports folder.
Figure 14: Create Report