Viavi OTU-8000 Parts list manual

OTU-8000(EOTU8000E)- Getting Started Manual – Ref 7OTU80060/00 – January 2013 – Copyright © 2013 JDSU 4
6
Click on APPLY to validate the changes of TCP/IP Configuration (this will restart the
OTU-8000).
7Connect the OTU-8000 to the LAN and try to connect to it by entering its IP adress
inside a Web Browser on a computer present on the LAN.
4. OPTICAL CONNECTIONS
OTDR
SWITCH PATCHCORD
The patchcord between the OTDR and the SWITCH is supplied with the OTU-8000.
The patchcords from the SWITCH to the monitored fibers are not supplied.
Once all the patchcords are plugged in, the plexy protector can be installed.
5. ADVANCED CONFIGURATION
For advanced configuration such as external optical switch, communication backup,
SMS, email consult the user manual available in pdf on the USB key.
6. TECHNICAL ASSISTANCE
If you need assistance or have questions related to the use of this product, call or e-mail
JDSU’s Technical Assistance Center for customer support.
Region Phone Number
Americas / Telecom Products /Other
countries
866 228 3762
World Wide: [phone] [email protected]
Europe, Africa, and Mid-East [phone] [email protected]
Asia and the Pacific Southeast Asia,
Australia, and New Zealand [phone] [email protected]
OTU-8000(EOTU8000E)- Getting Started Manual – Ref 7OTU80060/00 – January 2013 – Copyright © 2013 JDSU 1
OTU8000 GETTING STARTED MANUAL
The OTU-8000 installation requires going through :
- Mechanical installation - Communication setup
- Electrical connections - Optical connections
Female Ground
connector
0
$
,
1
%
$
&
.

/
2
&
O
T
U
-
8
0
0
0
V
2
<
-
>
O
S
X
8
0
0
0
C
a
b
l
e
IP NETWORK
- IP Address
- Subnet Mask
- Gateway
Male Ground
connector
OPTION CONVERTER AC-DC
- With female connector
SUPPLYING WIRES
- Ø 1.5 mm 2max
RELAY CONNECTOR
GSM Modem (Option)
Portable Phone
- SIM DATA Card
- No PIN Code
The OTU-8000 Serial Number is indicated below the equipment.
1. MECHANICAL INSTALLATION - INSTALLING THE OTU-8000 INTO THE RACK
1
Fix the brackets inside the rack.
Fixing brackets on the rack
(screws M6 and ring)
Le bracket (when you
are facing the OTU)
Right bracket (when you
are facing the OTU)
Indication for the
bracket size and position
into the rack

OTU-8000(EOTU8000E)- Getting Started Manual – Ref 7OTU80060/00 – January 2013 – Copyright © 2013 JDSU 2
2
Click the OTU-8000 on the brackets.
3
Fix the spacers in which the plexy protector will be screwed in.
Mark for wrench
HS8 1/4’’ (Inch)
2. ELECTRICAL CONNECTIONS
The OTU-8000 works on a DC -48V power supply. It supports a dual feed.
1
If using only one source, screw the
source’s wires inside the 5 points
connector as (one of the options)
shown opposite.
2
Wrap the power cables around the
ferite delivered.
3
Use the ground connector supplied
to connect the OTU-8000 to the
ground.
SWITCH ON/OFF PROCEDURES
The OTU-8000 has no ON/OFF button.
It is automatically switched ON once the power is plugged in.
SWITCH-OFF PROCEDURE
To switch the OTU-8000 off, the user must follow the procedure below
1. Keep the
OFF button pressed for about 3 sec.
2. Wait for the LED Standby to be solid green.
3. Unplug the Power-Supply connector.
OTU-8000(EOTU8000E)- Getting Started Manual – Ref 7OTU80060/00 – January 2013 – Copyright © 2013 JDSU 3
Test
Main
Backup
Stanby
Power
Unit
Local Off
Fuse
3. COMMUNICATION
The OTU-8000 is setup in DHCP mode with a host name such as: otu-8000e-5002 (5002
is the serial number)
To change the host name or the IP configuration follow the process below:
1
Plug in a PC (set in DHCP to obtain an IP automatically) to the RJ45 labelled
BACK/LOC.
2
Press the button Local during few seconds until the LED Main flashes.
48 V DC
Local buttonEthernet Cable
To enter the OTU’s network information:
3
Open your Web Browser http://192.168.1.1 .
4
Login as “user install”.
5In the configuration menu go to the Ethernet tab and indicate the OTU Network
settings:
-Hostname
-IP Address
-IP Sub-Mask
-IP Gateway
-Domain Name
-DNS Server address
To use the backup communication or to set up IPV6 please refer to the complete user
manual.