Viavi T-BERD/MTS 5800 Installation guide

VIAVI//Public
T-BERD/MTS 5800 Portable Network Tester
T-BERD/MTS-5800 Portable Network Tester
QUICK CARD
Testing Ethernet Voice over IP (VOIP) SIP Trunks
•This quick card describes how to configure and run an Ethernet VOIP Test to validate the
provisioning and performance of a Session Border Controller (SBC) and SIP trunk at the
network border. The following Information is needed to complete this test:
✓Physical Interface (RJ-45 Copper, 1000BASE-SX Multimode, 1000BASE-LX Single mode, etc.)
✓Speed andAuto Negotiation settings of the SBC LAN port
✓VLAN ID (if a VLAN is being used)
✓IP Address for the SBC LAN port
✓IP Address, Subnet mask, and default gateway for the T-BERD/MTS or PBX
✓Is registration required, or is this a non-registering trunk?
✓Username and Password (required for registering trunks only)
✓Customer’s Billing Telephone Number for the SIP trunk
✓Destination Telephone Number(s) for outbound call testing
•T-BERD/MTS 5800 equipped with the following:
oTransport software release V31.2.1 or greater
oTest options:
▪C5VOIP: Voice over IP option
▪C5BT: Bluetooth (optional, for Bluetooth headset)
▪C5LSCAPTURE or C510GCAPTURE (recommended for
packet capture and analysis)
•Headset (Plantronics M114/M210c, or BenertechA310QD)
•CAT5E or fiber optic cables to match the line under test
•For optical interfaces:
oFiber inspection microscope (P5000i or FiberChek Probe)
oFiber optic cleaning supplies Figure 1: Equipment Requirements
CONNECT HEADSET AND CONFIGURE AUDIO SETTINGS
1. Press the Power button to turn on the
T-BERD/MTS.
2. Connect the headset to the headset jack on
the side of the T-BERD/MTS.
3. Press the System icon in the top left
corner of the screen.
4. Press the Audio icon . Set Speaker
Volume near the maximum setting and set
Microphone Volume to the center setting.
If desired, you can adjust these settings
during the test. The speaker icon
on the top bar of the T-BERD provides a
shortcut to this screen.
Figure 3: Audio Settings
Figure 2: System menu

VIAVI//Public
T-BERD/MTS 5800 Portable Network Tester
T-BERD/MTS-5800 Portable Network Tester
QUICK CARD
2
LAUNCH TEST
1. Press the Test icon at the top of the
screen to display the Launch Screen.
2. Using the Select Test menu, Quick Launch
menu, or Job Manager, launch the Ethernet,
VoIP, Terminate test for the desired physical
interface/line rate and port; for example:
•Ethernet►1GigE Optical►VoIP►P1 Terminate
•Ethernet►10/100/1000►VoIP►P2 Terminate
►Note: If tests have been launched on both
Port 1 and Port 2, you must remove the test
on Port 2 before launching the VOIP test.
Tap the icon next to the Port 2 tab in the
Select Test bar or tap
in the Select Test menu to remove the test.
3. Tap to open the Tools Panel and
select .
4. Press to continue.
Figure 4: Launch Screen
Figure 5: Tools Panel
CONNECT TO LINE UNDER TEST
•For copper testing with the SmartClass 4800 or T-BERD/MTS 5800v2, connect the Port 1
10/100/1000 RJ-45 jack to the Ethernet port under test using CAT 5E or better cable.
•For copper testing with the T-BERD/MTS 5800-100G, connect the Port 2 10/100/1000 RJ-45 jack
to the Ethernet port under test using CAT 5E or better cable.
•For optical testing, insert an SFP or SFP+ into the Port 1 slot on the top of the T-BERD/MTS.
1. Ensure the fiber and connectors are clean using a Fiber Inspection microscope.
2. Connect the SFP or SFP+ to the Ethernet port under test.
▪Use Multimode jumper cables for 850 nm 1000BASE-SX or 10GBASE-SR.
▪Use Single mode jumper cables for 1310 nm 1000BASE-LX or 10GBASE-LR.
3. Select the Laser tab in the Main Action Panel and press to turn the Laser on.
Figure 6: T-BERD/MTS 5800v2 Figure 7: T-BERD/MTS 5800-100G

VIAVI//Public
T-BERD/MTS 5800 Portable Network Tester
T-BERD/MTS-5800 Portable Network Tester
QUICK CARD
3
CONFIGURE TEST
Folder
Option
Value(s)
VoIP,
General
Source Alias
For Registering Trunks, enter Billing Telephone Number (BTN) for the PBX.
For Non
-Registering Trunks, enter BTN@SBC LAN IP Address; user=phone.
i.e.“321555432[email protected];user=phone”
Outbound Alias
(Dial by)
For Registering Trunks, select “Phone Number”.
For Non
-Registering Trunks, select “ Name/URI/Email”
Dest
.
Phone Number/
Name /URI/ Email
For Registering trunks, enter your 10
-digit cell phone number.
For non
-registering trunks, enter Cell Phone Number@SBC LAN IP Address.
i.e. “3215551[email protected]”.
100 Rel Usage
Disabled
1. Press the Setup soft key on the top right side of the screen.
2. Select the indicated folders and configure your test as follows. Leave all other values at default,
unless specified in the work order.
Folder
Option
Value(s)
Interface,
Physical Layer
Auto Negotiation
Set to same value as the SBC LAN port under test. Enter
Speed if Auto
Negotiation is off; i.e., 100 Mbps.
Ethernet/IP
Encapsulation
None
or VLAN. Enter VLAN ID if VLAN is being used.
Source IP Type
Static
or DHCP.
Source IP
Enter the static Source IP Address for the T
-BERD/MTS/PBX.
Default Gateway
Enter the IP Address for the SBC LAN port.
Subnet Mask
Enter Subnet Mask for the T
-BERD/MTS/PBX.
Figure 8: Setup, Interface Figure 9: Setup, Ethernet/IP
Figure 10: Non-registering Trunk Setup, VOIP/General Figure 11: Registering Trunk Setup, VOIP/General

VIAVI//Public
T-BERD/MTS 5800 Portable Network Tester
T-BERD/MTS-5800 Portable Network Tester
QUICK CARD
4
3. If you have configured settings for a Registering Trunk, tap to verify connectivity to the SBC.
4. Tap the Results soft key to view the Test Results screen.
CONFIGURE TEST (continued)
Folder
Option
Value(s)
VoIP,
Proxy
Proxy Mode
For Registering Trunks, select “Static”
For Non
-Registering Trunks, select “No Proxy”
Proxy IP
SBC LAN IP Address
Proxy Username
Enter
User Name.
Proxy Password
Enter Password.
Figure 12: Non-registering Trunk Setup, VoIP/Proxy Figure 13: Registering Trunk Setup, VoIP/Proxy
VERIFY CONNECTIVITY AND REGISTRATION
1. Verify the following:
►Summary LED is green
►Network Up LED is green
►Sync Acquired LED is green
►Link Active LED is green
2. If you are testing a Registering Trunk and have configured VoIP/Proxy settings, the T-BERD/MTS
automatically sends a REGISTER message to the Proxy IP. A green phone labeled “Registered” in the
LED panel indicates successful registration.
Figure 14: Non-registering Trunk Results Figure 15: Registering Trunk Results

VIAVI//Public
T-BERD/MTS 5800 Portable Network Tester
T-BERD/MTS-5800 Portable Network Tester
QUICK CARD
5
1. Using your cell phone, dial the billing
telephone number (BTN) for the PBX (or dial
the temporary “test” number if the BTN has
not been ported).
2. In the T-BERD/MTS’s Actions Panel, select
the Call Controls tab. Allow the call to ring
at least 2 times. Confirm the Ring back tone
is heard on your cell phone and tap
on the T-BERD/MTS to answer the call.
3. Put on the headset. If the headset includes
an on/off switch and volume control, turn it
on and adjust the volume to the desired
level.
4. Confirm that voice is heard, and voice quality
is acceptable on both the T-BERD/MTS’s
headset and the Cell Phone. If static is
heard on your cell phone, move the
microphone boom farther away from your
mouth to avoid overdriving the microphone.
5. Hang up the call from your cell phone. Verify
that the call status on the T-BERD/MTS
changes to IDLE.
Figure 16: Results, Incoming call
INBOUND CALL TESTING
Figure 17: Results, Connected call
Figure 18: Results, Disconnected
VERIFY CONNECTIVITY AND REGISTRATION (continued)
Troubleshooting Tips:
1. If the specified LEDs are not green, verify the following:
►The T-BERD/MTS is configured correctly, as outlined above.
►The LAN Port of the SBC is properly configured and enabled.
►Cables are good quality and properly connected.
2. Tap the message icon in the top left screen to confirm DHCP IPAddress
assignment.
3. Change the results category and group from Summary/Status to Ethernet/Stats to view Ethernet
Statistics including Local Config Status and error counts.
4. Change the results category and group to Transaction Log/Signaling to view registration messages.
If the T-BERD/MTS fails to automatically register, tap the Register button in the Main Action Panel at
the bottom of the screen.
5. If your unit includes options for Packet Capture, start a capture session and view signaling messages
using WireShark.

VIAVI//Public
T-BERD/MTS 5800 Portable Network Tester
T-BERD/MTS-5800 Portable Network Tester
QUICK CARD
6
RUN TEST
1. In the T-BERDMTS’s Actions Panel, tap .
The T-BERD/MTS will transmit INVITE
messages to initiate the call. Call status is
displayed in the LED panel.
2. Answer the incoming call on your cell phone. If
the call is successful, Call Status will change
from Ringback to Conversation.
3. Converse and confirm that voice quality is
acceptable on the T-BERD/MTS and the Cell
Phone. A wide variety of call statistics can be
viewed in the results screen, by changing the
Results category and group from
Summary/Status to other selections including
Content/Current Call Scores, Transport/QOS,
Ethernet/Stats, and more.
4. In the T-BERD/MTS Main Actions Panel, tap
to disconnect the call.
5. In the T-BERD/MTS Quick Config menu,
change “Destination Phone Number” to the next
number in the call plan.
6. In the T-BERD/MTS Main Actions Panel, tap
to initiate the call.
7. Converse and confirm that voice quality is
acceptable on the T-BERD/MTS and for the
called party.
8. In the T-BERD/MTS Actions Panel, tap
to disconnect the call.
9. Repeat steps 5 through 8 for all numbers in
the call plan. Call Plans may include:
•Toll Free numbers
•Local off-network numbers
•Local on-network numbers
•Long Distance numbers
•International numbers
•Blocked Calls
•n11 numbers such as 411 (directory
assistance), 611 (customer service), and
911 (emergency services)
Figure 19: Results, Place Call
OUTBOUND CALL TESTING
Figure 20: Results, Connected call
Figure 21: Results, Content/Current Call Scores

VIAVI//Public
T-BERD/MTS 5800 Portable Network Tester
T-BERD/MTS-5800 Portable Network Tester
QUICK CARD
© 2023 VIAVI Solutions, Inc,
Product specifications and descriptions in this
document are subject to change without notice.
Patented as described at viavisolutions.com/patents
Contact Us
To reach the VIAVI office nearest you,
visit viavisolutions.com/contact
+1 844 GO VIAVI
([phone])
CREATE REPORT
1. Tap to open the Reports Panel and
select . .
2. Tap .
3. A report will be saved to the T-BERD/MTS
/bert/reports folder.
Figure 22: Create Report