Viavi AVX-10K User manual

AVX-10K
Flight Line Test Set
Operation Manual

VIAVI Solutions
1-844-GO-VIAVI
www.viavisolutions.com
AVX-10K
Flight Line Test Set
Operation Manual
22135254 / Rev. 004

22135254 AVX-10K Operation Manual Rev. 004
January 2024 1
Notice
Every effort was made to ensure that the information in this manual was accurate at the time of release.
However, information is subject to change without notice, and VIAVI reserves the right to provide an
addendum to this manual with information not available at the time that this manual was created.
Copyright/Trademarks
© Copyright 2024 VIAVI Solutions, Inc. All rights reserved. No part of this guide may be reproduced or
transmitted, electronically or otherwise, without written permission of the publisher. VIAVI Solutions and
the VIAVI logo are trademarks of VIAVI Solutions Inc. (“VIAVI”).
All other trademarks and registered trademarks are the property of their respective owners.
Patent Information
Patented as described at www.viavisolutions.com/patents
Copyright Release
Reproduction and distribution of this guide is authorized for US Government purposes only.
Terms and conditions
Specifications, terms, and conditions are subject to change without notice. The provision of hardware,
services, and/or software are subject to VIAVI’s standard terms and conditions, available at
www.viavisolutions.com/en/terms-and-conditions.
Declaration of Conformity
VIAVI recommends keeping a copy of the Declaration of Conformity that shipped with the unit with the
test set at all times.
Warranty Information
Warranty information for this product is available on the VIAVI website at
https://www.viavisolutions.com/en-us/warranty-information.
Low Voltage Directive Compliance
This product was tested and conforms to the Low Voltage Directive, 73/23/EEC as amended by
93/68/EEC.

Rev. 004 AVX-10K Operation Manual 22135254
2 January 2024
Federal Communications Commission (FCC) Notice
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment was tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference, in which case you will be required to correct
the interference at your own expense.
The authority to operate this equipment is conditioned by the requirements that no modifications be made
to the equipment unless the changes or modifications are expressly approved by VIAVI.
GITEKI Certification (Japan)
The Giteki certification includes two types namely Technical Standards Conformity Certification and
Construction Design (Construction Type) Certification.
Technical Standards Conformity Certification
Certify and test for conformity of an equipment for each unit to which the certification mark "Giteki" and ID
number is granted. Applicable to small production and prototype production.
Construction Design/Type Certification
Certify Construction Design of an equipment and test per model to which the "Giteki" mark and ID number
is granted. The Certification does not limit the quantity of the equipment as long as the equipment is
manufactured by the same design and the manufacturing method is applied as the certified model.
The Specified Radio Equipment connected to telecommunication network requires compliance to
technical standards conformity in both Japan Telecommunications Business law and Japan Radio Law.
ALERT
•To comply with FCC RF Exposure compliance requirements, a separation distance of at
least 20 cm must be maintained between the antenna of this device and all persons.
•This transmitter must not be co-located in conjunction with any other antenna or
transmitter.
該機器には電波法に基づく、技術基準適合証明等を受けた特定無線設備を装着している
波法により5.2/5.3GHz帯は屋内使用に限ります

22135254 AVX-10K Operation Manual Rev. 004
January 2024 3
Industry Canada Requirements
This device complies with Industry Canada's license-exempt RSSs. Operation is subject to the following
two conditions: 1) This device may not cause interference; and, 2) This device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts
de licence. L'exploitation est autorisée aux deux conditions suivantes: 1) l'appareil ne doit pas produire
de brouillage; et, 2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
EU WEEE and Battery Directives
This product, and the battery used to power the product, should not be disposed of as unsorted
municipal waste and should be collected separately and disposed of according to your national
regulations.
VIAVI has established a take-back processes in compliance with the EU Waste Electrical and Electronic
Equipment (WEEE) Directive, 2012/19/EU, and the EU Battery Directive, 2006/66/EC.
Instructions for returning waste equipment and batteries to VIAVI can be found in the WEEE section of
VIAVI’s Standards and Policies web page.
If you have questions concerning disposal of your equipment or batteries, contact the VIAVI WEEE
Program Management team at WEEE.E[email protected].
EU REACH
Article 33 of EU REACH regulation (EC) No 1907/2006 requires article suppliers to provide information if
a listed Substances of Very High Concern (SVHC) is present in an article above a certain threshold.
For information on the presence of REACH SVHCs in VIAVI products, see the Hazardous Substance
Control section of VIAVI’s Standards and Policies web page.
EU CE Marking Directives (LV, EMC, RoHS, RE)
This product conforms with all applicable CE marking directives. Please see EU Declaration of
Conformity for details.
EMC Directive Compliance
This product was tested and conforms to the EMC Directive, 2014/30/EU for electromagnetic
compatibility.
UK Declaration of Conformity
This product conforms with all applicable UKCA marking directives. Please request UK Declaration of
Conformity for further details.

Rev. 004 AVX-10K Operation Manual 22135254
4 January 2024
China RoHS Materials Declaration
The China RoHS Materials Declaration is shipped with the product when required.
California Proposition 65
California Proposition 65, officially known as the Safe Drinking Water and Toxic Enforcement Act of
1986, was enacted in November 1986 with the aim of protecting individuals in the state of California and
the state's drinking water and environment from excessive exposure to chemicals known to the state to
cause cancer, birth defects or other reproductive harm.
For the VIAVI position statement on the use of Proposition 65 chemicals in VIAVI products, see the
Hazardous Substance Control section of VIAVI’s Standards and Policies web page.
Korea Certification
Ordering information
This manual is a product of the VIAVI Technical Publications Department, issued for use with the AVX-10K
Flight Line Test Set. The PDF format of this manual is available on the VIAVI product website.
Go to: https://www.viavisolutions.com/en-us/resources/literature-library
•Type AVX-10K to find the manuals associated with the AVX-10K Flight Line Test Set.
•The part number of the Operation Manual CD is 22141759.
Contact Information
Contact the Technical Assistance Center (TAC) for technical support or with any questions regarding this
or other VIAVI products.
•Phone: 1-844-GO-VIAVI
•Email: Tech[email protected]
For the latest TAC information, go to:
https://www.viavisolutions.com/support/technical-product-support
Class A Equipment (Industrial Broadcasting &
Communications Equipment).
This equipment is Industrial (Class A) electromagnetic wave suitability
equipment and seller or user should take notice of it, and this
equipment is to be used in the places except for home.

Software Notifications
22135254 AVX-10K Operation Manual Rev. 004
January 2024 5
Software Notifications
DFARS Statement
If software is for use in the performance of a U.S. Government prime contract or subcontract, software is
delivered and licensed as “Commercial Computer Software” as defined in DFAR 252.227-7014 (Feb
2014), or as a “Commercial Item” as defined in FAR 2.101(a) or as “Restricted Computer Software” as
defined in FAR 52.227-19 (Dec 2007) or any equivalent agency regulation or contract clause. Use,
duplication or disclosure of Software is subject to VIAVI Solutions' standard commercial license terms,
and non-DOD Departments and Agencies of the U.S. Government will receive no greater than Restricted
Rights as defined in FAR 52.227-19(c)(1-2) (Dec 2007). U.S. Government users will receive no greater
than Limited Rights as defined in FAR 52.227-14 (June 1987) or DFAR 252.227-7015 (b)(2) (November
1995), as applicable in any technical data.
Open Source Disclaimer - IMPORTANT READ CAREFULLY
The AVX-10K Flight Line Test Set includes third party software licensed under the terms of separate open
source software licenses. By using this software you agree to comply with the terms and conditions of the
applicable open source software licenses. Software originated by VIAVI is not subject to third party
licenses. Terms of the VIAVI Software License different from applicable third party licenses are offered by
VIAVI alone.

22135254 AVX-10K Operation Manual Rev. 004
January, 2024 Safety - 7
Safety and Compliance Information
Read and follow all warning notices and instructions marked on the product and included
in user documentation.
Symbols and Markings
The following symbols and markings are found on the instrument and in product
documentation:
Table 1 Symbols and Markings
This symbol indicates a note that includes important supplemental
information or tips related to the main text.
Attention Symbol
This symbol represents a general hazard. It may be associated with either a
DANGER, WARNING, CAUTION, or ALERT message. See Table 2 for more
information.
ESD Sensitive
Indicates item is static sensitive. Item should only be handled by Qualified
Service Personnel.
Explosive Hazard
This symbol represents a risk of explosion. It may be associated with either a
DANGER, WARNING, CAUTION or ALERT message.
Voltage Symbol
This symbol represents hazardous voltages. It may be associated with either
a DANGER, WARNING, CAUTION, or ALERT message. See Table 2 for
more information.
Toxic Symbol
Indicates a toxic hazard. Item should only be handled by Qualified Service
Personnel. Dispose of item in accordance with local regulations.
WEEE Symbol
This symbol, located on the equipment or the packaging indicates that the
equipment must not be disposed of in a land-fill site or as municipal waste,
and should be disposed of according to your national regulations.
CE Compliant
CE Label indicates item meets the requirements of the applicable European
Directives.
Fuse Symbol
Indicates a fuse location (AC or DC).

Rev. 004 AVX-10K Operation Manual 22135254
Safety - 8 January, 2024
Safety Definitions
This manual uses the following terms to indicate conditions or activities which are potential
safety hazards:
Safety Hazards
Toxic Hazards
Table 2 Safety Definitions
Term Definition
WARNING Identifies conditions or activities that, if ignored, can result in
personal injury or death.
Avertissement Identifiez les conditions ou les activités qui, si ignorées, peuvent
entraîner des blessures personnelles voire mortelles.
CAUTION Identifies conditions or activities that, if ignored, can result in
equipment or property damage, e.g., Fire.
Mise en Garde Identifiez les conditions ou les activités qui, si ignorées, peuvent
entraîner des dommages à l’équipement ou aux biens, p. ex. un
incendie.
WARNING
Some of the components used in this device may include resins and other materials
which give off toxic fumes if incinerated. Dispose of such items appropriately.
Avertissement
Certains des composants utilisés dans cet appareil peuvent comprendre des résines
et d’autres matériaux qui produisent des émanations toxiques lorsqu’ils sont
incinérés. Éliminez adéquatement de tels éléments.
WARNING
A Lithium-Ion battery is used in this equipment. Lithium is a toxic substance.
•Do not crush, incinerate or dispose of in normal waste.
•Do not short circuit or force discharge since this might cause the battery to
vent, overheat or explode.

22135254 AVX-10K Operation Manual Rev. 004
January, 2024 Safety - 9
WEEE and Battery Statement
This product and the batteries used to power the product, should not be disposed of as
unsorted municipal waste and should be collected separately and disposed of according
to local regulations.
VIAVI has established a take-back processes in compliance with the EU Waste Electrical
and Electronic Equipment (WEEE) Directive, 2012/19/EU, and the EU Battery Directive,
2006/66/EC.
Information and instructions for returning waste equipment and batteries to VIAVI can be
found on the VIAV website in the WEEE section of VIAVI’s Standards and Policies web
page at: VIAVI’s Standards and Policies web page.
Beryllia
WARNING
Beryllia (beryllium oxide) is used in the construction of some of the components in this
equipment.
This material, when in the form of fine dust or vapor and inhaled into the lungs, can
cause a respiratory disease. In its solid form, as used here, it can be handled safely,
however, avoid handling conditions which promote dust formation by surface
abrasion.
Use care when removing and disposing of these components. Do not put them in the
general industrial or domestic waste or dispatch them by post. They should be
separately and securely packed and clearly identified to show the nature of the hazard
and then disposed of in a safe manner by an authorized toxic waste contractor.

Rev. 004 AVX-10K Operation Manual 22135254
Safety - 10 January, 2024
Beryllium Copper
Lithium-Ion
WARNING
Some mechanical components within this instrument are manufactured from beryllium
copper. Beryllium copper represents no risk in normal use. The material should not be
machined, welded or subjected to any process where heat is involved.
Beryllium copper must NOT be disposed of by incineration. Beryllium copper must be
disposed of as “special waste” per local regulations.
WARNING
A Lithium-Ion battery is used in this device. Lithium-Ion is a toxic substance, so the
battery should in no circumstances be crushed, incinerated or disposed of in normal
waste.
•Do not attempt to recharge this type of battery.
•Do not short circuit or force discharge since this might cause the battery to vent,
overheat or explode.
CAUTION
This device contains a Lithium-Ion battery and may require special packaging and
external labeling when shipping. Contact VIAVI for packaging and labeling
instructions.
Mise en Garde
Cet appareil contient une batterie au lithium-ion et peut nécessiter un emballage
spécial et un étiquetage externe lors de l'expédition. Contactez VIAVI pour l'emballage
et les instructions étiquetantes.

22135254 AVX-10K Operation Manual Rev. 004
January, 2024 Safety - 11
Electrical Hazards
Grounding the Instrument
The instrument is provided with a protective grounding lead that conforms with IEC Safety
Class I. The supply lead must always be connected to the power supply via a grounded
contact in order to maintain the grounding protection. The instrument must be properly
grounded to prevent damage to the device from electrostatic discharge (ESD).
Input Overload
Refer to product labeling and product specifications for maximum input ratings.
WARNING
Improper grounding of equipment can result in electrical shock. To ensure proper
grounding, this device should only be connected to a grounded AC Power Supply.
Avertissement
La mise à la terre inadéquate de l’équipement peut entraîner un choc électrique. Pour
s'assurer d’une mise à la terre adéquate, cet appareil doit seulement être branché à
une alimentation électrique CA mise à la terre.
CAUTION
Do not overload input connectors. Refer to product specifications or the product data
sheet for maximum input ratings.
Mise en Garde
Ne surchargez pas les connecteurs d'entrée. Reportez-vous aux spécifications du
produit ou à la fiche technique du produit pour connaître les valeurs d'entrée
maximales.

Rev. 004 AVX-10K Operation Manual 22135254
Safety - 12 January, 2024
AC Power Adapter/Cord
Approved Part: 22146602, AC Power Adapter/Cord.
The base unit with all applications installed can operate supplied by the AC power
adapter/cord that is shipped with the unit.
The mains supply cord used with the power adapter must be grounded with a connection
to protective earth.
CAUTION
•Only use the AC Power Adapter/Cord supplied with the instrument.
•Do not use the AC Power Adapter/Cord outdoors or in a wet or damp location.
•Only connect the AC Power Adapter/Cord to the correct mains voltage indicated
on the ratings label.
•Do not use the AC Power Adapter/Cord if it appears damaged or modified.
Mise en Garde
•Utilisez uniquement l'adaptateur secteur / le cordon d'alimentation fourni avec
l'instrument.
•N'utilisez pas l'adaptateur secteur / le cordon d'alimentation à l'extérieur ou
dans un endroit mouillé ou humide.
•Connectez uniquement l'adaptateur secteur / cordon d'alimentation à la tension
secteur appropriée indiquée sur l'étiquette des caractéristiques nominales.
•N'utilisez pas l'adaptateur / cordon d'alimentation secteur s'il semble
endommagé ou s'il a été modifié.

22135254 AVX-10K Operation Manual Rev. 004
January, 2024 Safety - 13
Residual Current
CAUTION
•Do not use the power cord if it is damaged or frayed. Replace damaged power
cords with cable of the same ratings.
•Do not position the power cord in a manner that makes it difficult to disconnect
from the main voltage.
•Do not allow anything to rest on the power cord.
•Do not locate the product where persons can walk on or trip over the power
cord.
Mise en Garde
•N'utilisez pas le cordon d'alimentation s'il est endommagé ou effiloché.
Remplacez les cordons d'alimentation endommagés par des câbles de même
puissance.
•Ne placez pas le cordon d'alimentation de manière à rendre difficile la
déconnexion de la tension secteur.
•Ne laissez rien reposer sur le cordon d'alimentation.
•Ne placez pas le produit à un endroit où des personnes pourraient marcher ou
trébucher sur le cordon d'alimentation.
WARNING
The supply filter contains capacitors that may remain charged after the instrument is
disconnected from the power supply. The residual energy is within the approved
safety requirements, however, a slight shock may be felt if the plug pins are touched
immediately after removal.
Avertissement
Le filtre d’alimentation contient des condensateurs qui peuvent rester chargés une fois
l’appareil débranché de l'alimentation électrique. L’énergie résiduelle est dans les
limites des exigences de sécurité approuvées. Par contre, un léger choc électrique
peut être ressenti si l’on touche les broches de la prise immédiatement après son
débranchement.

Rev. 004 AVX-10K Operation Manual 22135254
Safety - 14 January, 2024
Battery Safety Information
The battery included with the product should only to be used with VIAVI AVX-10K Flight
Line Test Set.
Battery Storage, Handling and Disposal
Battery Replacement
Approved Part Number: 22071316-002, Lithium Ion Battery
CAUTION
•To avoid risk of fire and burns, do not tamper with the batteries.
•Do not open, crush, or incinerate the batteries.
•Do not use or store the batteries in temperatures that exceed product
specifications.
•Avoid shorting the batteries.
•Never use a battery that appears damaged or abused.
•Only charge the batteries with the charger that shipped with the test set.
Mise en Garde
•Ne pas ouvrir, écraser ni incinérer la batteries.
•N'utilisez pas et ne stockez pas la batteries à des températures dépassant les
spécifications du produit.
•Évitez de court-circuiter la batteries.
•N'utilisez jamais une batterie qui semble endommagée ou qui a subi des abus.
•Accusez seulement la batteries du chargeur qui a expédié avec le jeu d'essai.
CAUTION
The battery supplied with the device should only be replaced with a replacement part
that has been approved by VIAVI.
Mise en Garde
La deux battery fournie avec l'appareil ne doit être remplacée que par une pièce de
rechange approuvée par VIAVI.

22135254 AVX-10K Operation Manual Rev. 004
January, 2024 Safety - 15
Equipment Usage
This device is designed and tested to comply with the requirements of ‘IEC/EN 61010-1,
3rd Edition Safety Requirements for Electrical Equipment for Measurement, Control and
Laboratory Use’ for Class I portable equipment and is for use in a pollution degree 2
environment.
Electrostatic Discharge (ESD)
Case/Cover Removal
Do not operate this device with the case or covers removed. Opening or removing covers
may expose you to dangerous high voltage points and other hazards.
WARNING
Operating this device in a manner not specified in accompanying documentation may
impair the safety protection built into the device.
Avertissement
Utiliser cet appareil de manière non spécifiée dans la documentation
d'accompagnement peut nuire au dispositif de protection de sécurité intégré dans
l’appareil.
CAUTION
Internal components are ESD sensitive and should only be installed, removed and/or
serviced by Qualified Service Personnel.
Mise en Garde
Les composants internes sont sensibles au DES et ne doivent être installés, retirés ou
entretenus que par du personnel de maintenance qualifié.
CAUTION
This device does not contain user serviceable parts. Servicing should only be
performed by Qualified Service Personnel.
Mise en Garde
Cet appareil ne contient pas de pièces pouvant être entretenues par l’utilisateur.
L’entretien doit seulement être effectué par du personnel de service qualifié.

Rev. 004 AVX-10K Operation Manual 22135254
Safety - 16 January, 2024
Ventilation Requirements
The instrument is cooled by internal fans. Failure to provide proper ventilation may result
in damage to the instrument. Observe the following precautions when operating the
instrument:
Electromagnetic Interference (EMI)
This product complies with Part 15 of the FCC Rules for a Class A device. Operation is
subject to the following two conditions: (1) this product may not cause harmful
interferences, and (2) this product must accept any interferences received, including
interference that may cause undesired operation.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This product generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this product does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Use properly shielded and grounded cables and connectors in order to meet FCC
emission limits.
CAUTION
•Do not obstruct air flow to the air vents.
•Do not place the instrument on or close to other heat-generating equipment.
•Do not operate device in an enclosure such as the soft-shell travel case.
Mise en Garde
•N’obstruez pas l’écoulement d’air vers les évents.
•Ne placez pas l'instrument sur ou près de tout autre équipement générant de la
chaleur.
•N'utilisez pas l'appareil dans un boîtier tel que l'étui de voyage à coque souple.

22135254 AVX-10K Operation Manual Rev. 004
January, 2024 Safety - 17
CAUTION
Signal generators can be a source of Electromagnetic Interference (EMI) to
communication receivers. Some transmitted signals can cause disruption and
interference to communication services out to a distance of several miles. Users of
this equipment should scrutinize any operation that results in radiation of a signal
(directly or indirectly) and should take necessary precautions to avoid potential
communication interference problems.
Mise en Garde
Les générateurs de signaux peuvent constituer une source d'interférences
électromagnétiques (IME) pour les récepteurs radio. Certains signaux émis peuvent
provoquer des interférences et des interruptions des communications sur une
distance de plusieurs kilometres. Les utilisateurs de cet équipment doivent examiner
soigneusement tout fonctionnement provoquant le rayonnement d'un signal (direct ou
indirect) et ils doivent prendre les dispositions nécessaires afin d'eviter des problémes
potentiels d'interferénces sur les communications.

This page intentionally left blank.

22135254 AVX-10K Operation Manual Rev. 004
January, 2024 TOC - 1
Table of Contents
Chapter 1 Overview AVX-10K . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1.1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1.2 Principles of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1.3 Platform and System Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
1.4 Features and Capabilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1.5 Device Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
1.6 First Time Use and Self-Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Chapter 2 Setup, Control, and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2.1 Control and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.2 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2.2.1 Controls and Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
2.2.2 I/O Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
2.2.3 Hand Strap Rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2.2.4 Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2.2.5 Display Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
2.3 Remote Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
2.3.1 Mobile Tech Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
2.3.2 VNC Viewer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
2.3.3 Smart Access Anywhere Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
2.3.4 HTTP File Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
2.4 User Interface (UI) Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
2.4.1 General Screen Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
2.4.2 Home Screen Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
2.4.3 Application Screen Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
2.5 UI Header Info and Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19
2.6 UI Navigation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
2.7 Selecting and Entering Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23