Vision Fitness X6600HRT User manual

Assembly
Guide
X6600HRT
COMMERCIAL ELLIPTICAL TRAINER

1
STEP
2
STEP
4
STEP
4
STEP
To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding, find
your new Elliptical Trainer’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Elliptical Trainer.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Elliptical Trainer to prevent loos-
ening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely
tightening any ONE screw.
Assembly
Guide
X6600HRT
COMMERCIAL ELLIPTICAL TRAINER

TOOLS & PARTS INCLUDED
5MM Allen Wrench
17MM Socket Wrench
Screwdriver
8MM L-Shaped Wrench
PARTS BOX
Console Mast Cover, Qty: 1
Water Bottle & Cage, Qty: 1
Heart Rate Chest Strap, Qty:1
Link Arm Covers, Qty: 2
Pedal Support Brackets, Qty: 2
Dual Action End Caps, Qty: 2
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card
6MM Allen Wrench
10MM L-Shaped Wrench

HARDWARE INCLUDED
ORANGE BAG
M10x70L CapScrew
Quantity: 2
BLUE BAG
M8x15L Screw
Quantity: 2
M20x30x1.5T
Wavy Washer
Quantity: 2
M8x10L Screw
Quantity: 4
M8x80L SocketHead CapScrew
Quantity: 1
FOR SERVICE ONLY
M12x60L CapScrew
Quantity: 1
M49x7 Round Tool
Quantity: 1
M6x40L CapScrew
Quantity: 3
PINK BAG
M10x18x2T Washer
Quantity: 4
M5x12L Screw
Quantity: 6
M5.3x10x1T Washer
Quantity: 4
M10x40L CapScrew
Quantity: 2
M10 Nut
Quantity: 2
M8x30L CapScrew
Quantity: 8
6MM L-Shaped Wrench

1
STEP
5
1
STEP
• Place the rubber console mast boot
on the end of the console mast.
• Connect the wire tie that exits the
bottom of the console mast to the wire
harness that sits in the bracket at the top
of the frame. Pull the wire tie and wire
harness up through the console mast
while at the same time inserting the
console mast into the frame bracket.
• Secure the console mast to the frame
with two capscrews (M10 x 70L).
Tighten with the 8MM L-shaped Allen
wrench.
• Stabilize the console mast to the
frame with the socket head screw
(M8x80L). Tighten with the 10MM
L-shaped Allen wrench.
• Slide the rubber boot down the
console mast and snap it in place so
it integrates with the side covers.
ORANGE BAG

6
2
STEP
• Place a wavy washer
(M20x30x1.5t) on the axle located
under the foot plate of the right lower
link arm.
• Slide the axle of the lower link arm
into the bracket located on the top of
the right pedal arm. Secure lower link
arm by attaching the pedal support
bracket and screw (M8x15L) to the
end of the axle. Secure the outside
holes in the bracket to the footplate
with two screws (M8x10L). Tighten
screws with the 5MM T-handled Allen
wrench.
• Repeat the same steps on the left
side.
BLUE BAG
2
STEP

7
3
STEP
3
STEP
• Connect the right dual-action arm to
the right console mast rotation
housing, being sure to line up the
holes. Secure the dual action arm in
place with four screws (M8x30L) and
tighten with a 6MM T-handled Allen
wrench. Snap the dual action end
cap into place.
• Connect the right lower link arm to
the right dual-action arm by lining up
the holes on the end of each arm.
Place a washer (M10.5x18x2t) on
the capscrew (M10x40L) and slide
the capscrew through the hole. Place
a second washer followed by a nut
(M10) on the capscrew and tighten
using the 17MM socket wrench and
8MM Allen wrench.
• Position the link arm cover into
place over the joint of the lower link
arm and dual-action arm. With a
screw (M5x12L) and Phillips
screwdriver, connect the two halves of
the cover through the hole located in
the front of the cover. Attach the cover
to each side of the lower link arm with
the two washers (M5.3x10x1t) and
two screws (M5x12L).
• Repeat these same steps on the left
side.
PINK BAG

500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2002 Vision Fitness. All Rights Reserved. 12.02 Part #Z66EP35-AG1820PRD
AG18.20PRD
REV2
8
4
STEP
• Remove the four screws from the
back of the console.
• Make sure the 9 Volt battery is
plugged in and in place in the back
of the console.
• Plug the wire harness and heart rate
wires into the console.
• Mount the console to the console
mast with the four screws you
removed earlier in this step.
• Attach water bottle cage to the
console mast with the two included
screws and Phillips screwdriver. Insert
the water bottle.
CONSOLE
4
STEP